We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Power Delivery Specification (v3.0) dictates in ch. 6.4.1 - Capabilities Message - that the vSafe5V Fixed Supply Object shall always be the first object. tcpm.c now checks that this rule is obeyed (commit 5007e1b5db73 "typec: tcpm Validate source and sink caps"), and that makes the typec_wcove.c fail to probe. The voltage is higher then what is permitted for the vSafe5V parameter. Dropping the voltage in the first Fixed Supply object of the sink capabilities down to 5V, and maximum current down to 500mA, making the driver probe successfully again. Also, removing the Battery and Variable Supply objects, as there is no need for them. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present, TCPM code assumes that local device supports variable/batt pdos and always selects the pdo with highest possible power within the board limit. This assumption might not hold good for all devices. To overcome this, this patch makes TCPM only accept a source_pdo when there is a matching sink pdo. For Fixed pdos: The voltage should match between the incoming source_cap and the registered snk_pdo For Variable/Batt pdos: The incoming source_cap voltage range should fall within the registered snk_pdo's voltage range. Also, when the cap_mismatch bit is set, the max_power/current should be set to the max_current/power of the sink_pdo. This is according to: "If the Capability Mismatch bit is set to one The Maximum Operating Current/Power field may contain a value larger than the maximum current/power offered in the Source Capabilities message’s PDO as referenced by the Object position field. This enables the Sink to indicate that it requires more current/power than is being offered. If the Sink requires a different voltage this will be indicated by its Sink Capabilities message. Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The source and sink caps should follow the following rules. This patch validates whether the src_caps/snk_caps adheres to it. 6.4.1 Capabilities Message A Capabilities message (Source Capabilities message or Sink Capabilities message) shall have at least one Power Data Object for vSafe5V. The Capabilities message shall also contain the sending Port’s information followed by up to 6 additional Power Data Objects. Power Data Objects in a Capabilities message shall be sent in the following order: 1. The vSafe5V Fixed Supply Object shall always be the first object. 2. The remaining Fixed Supply Objects, if present, shall be sent in voltage order; lowest to highest. 3. The Battery Supply Objects, if present shall be sent in Minimum Voltage order; lowest to highest. 4. The Variable Supply (non-battery) Objects, if present, shall be sent in Minimum Voltage order; lowest to highest. Errors in source/sink_caps of the local port will prevent the port registration. Whereas, errors in source caps of partner device would only log them. Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These duplicate includes have been found with scripts/checkincludes.pl but they have been removed manually to avoid removing false positives. Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is more clear from user perspective to wrap the whole USB Type-C support under a single option that the user can select, then it is to always ask the user for every USB Type-C and USB Power Delivery driver separately. Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expectation in the FUSB302 driver is that a TX_SUCCESS event should occur after a message has been sent, but before a GCRCSENT event is raised to indicate successful receipt of a message from the partner. However in some circumstances it is possible to see the hardware raise a GCRCSENT event before a TX_SUCCESS event is raised. The upshot of this is that the GCRCSENT handling portion of code ends up reporting the GoodCRC message to TCPM because the TX_SUCCESS event hasn't yet arrived to trigger a consumption of it. When TX_SUCCESS is then raised by the chip it ends up consuming the actual message that was meant for TCPM, and this incorrect sequence results in a hard reset from TCPM. To avoid this problem, this commit updates the message reading code to check whether a GoodCRC message was received or not. Based on this check it will either report that the previous transmission has completed or it will pass the msg data to TCPM for futher processing. This way the incorrect ordering of the events no longer matters. Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probe fails, fusb302_debugfs_exit is called making it impossible to view any logs so use normal dev_err for any error messages during probe. Signed-off-by: Mats Karrman <mats.dev.list@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB/PHY updates from Greg KH: "Here is the big set of USB and PHY driver updates for 4.15-rc1. There is the usual amount of gadget and xhci driver updates, along with phy and chipidea enhancements. There's also a lot of SPDX tags and license boilerplate cleanups as well, which provide some churn in the diffstat. Other major thing is the typec code that moved out of staging and into the "real" part of the drivers/usb/ tree, which was nice to see happen. All of these have been in linux-next with no reported issues for a while" * tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits) usb: gadget: f_fs: Fix use-after-free in ffs_free_inst USB: usbfs: compute urb->actual_length for isochronous usb: core: message: remember to reset 'ret' to 0 when necessary USB: typec: Remove remaining redundant license text USB: typec: add SPDX identifiers to some files USB: renesas_usbhs: rcar?.h: add SPDX tags USB: chipidea: ci_hdrc_tegra.c: add SPDX line USB: host: xhci-debugfs: add SPDX lines USB: add SPDX identifiers to all remaining Makefiles usb: host: isp1362-hcd: remove a couple of redundant assignments USB: adutux: remove redundant variable minor usb: core: add a new usb_get_ptm_status() helper usb: core: add a 'type' parameter to usb_get_status() usb: core: introduce a new usb_get_std_status() helper usb: core: rename usb_get_status() 'type' argument to 'recip' usb: core: add Status Type definitions USB: gadget: Remove redundant license text USB: gadget: function: Remove redundant license text USB: gadget: udc: Remove redundant license text USB: gadget: legacy: Remove redundant license text ...
Pull staging and IIO updates from Greg KH: "Here is the "big" staging and IIO driver update for 4.15-rc1. Lots and lots of little changes, almost all minor code cleanups as the Outreachy application process happened during this development cycle. Also happened was a lot of IIO driver activity, and the typec USB code moving out of staging to drivers/usb (same commits are in the USB tree on a persistent branch to not cause merge issues.) Overall, it's a wash, I think we added a few hundred more lines than removed, but really only a few thousand were modified at all. All of these have been in linux-next for a while. There might be a merge issue with Al's vfs tree in the pi433 driver (take his changes, they are always better), and the media tree with some of the odd atomisp cleanups (take the media tree's version)" * tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits) staging: lustre: add SPDX identifiers to all lustre files staging: greybus: Remove redundant license text staging: greybus: add SPDX identifiers to all greybus driver files staging: ccree: simplify ioread/iowrite staging: ccree: simplify registers access staging: ccree: simplify error handling logic staging: ccree: remove dead code staging: ccree: handle limiting of DMA masks staging: ccree: copy IV to DMAable memory staging: fbtft: remove redundant initialization of buf staging: sm750fb: Fix parameter mistake in poke32 staging: wilc1000: Fix bssid buffer offset in Txq staging: fbtft: fb_ssd1331: fix mirrored display staging: android: Fix checkpatch.pl error staging: greybus: loopback: convert loopback to use generic async operations staging: greybus: operation: add private data with get/set accessors staging: greybus: loopback: Fix iteration count on async path staging: greybus: loopback: Hold per-connection mutex across operations staging: greybus/loopback: use ktime_get() for time intervals staging: fsl-dpaa2/eth: Extra headroom in RX buffers ...