linux.git/drivers/usb/serial, branch v6.2-rc3

treewide: Convert del_timer() to timer_shutdown()

2022-12-25T21:38:09+00:00

Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown".  After a timer is set to this state, then it can no
longer be re-armed.

The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed.  It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.

This was created by using a coccinelle script and the following
commands:

    $ cat timer.cocci
    @@
    expression ptr, slab;
    identifier timer, rfield;
    @@
    (
    -       del_timer(&ptr->timer);
    +       timer_shutdown(&ptr->timer);
    |
    -       del_timer_sync(&ptr->timer);
    +       timer_shutdown_sync(&ptr->timer);
    )
      ... when strict
          when != ptr->timer
    (
            kfree_rcu(ptr, rfield);
    |
            kmem_cache_free(slab, ptr);
    |
            kfree(ptr);
    )

    $ spatch timer.cocci . > /tmp/t.patch
    $ patch -p1 < /tmp/t.patch

Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) 
Acked-by: Pavel Machek  [ LED ]
Acked-by: Kalle Valo  [ wireless ]
Acked-by: Paolo Abeni  [ networking ]
Signed-off-by: Linus Torvalds

Merge tag 'usb-serial-6.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

2022-12-08T15:24:46+00:00

Johan writes:

USB-serial updates for 6.2-rc1

Here are the USB-serial updates for 6.2-rc1, including:

 - B0 hangup support for cp210x
 - avoid requesting a zero DTE rate which could potentially confuse
   buggy firmware in XR devices

Included are also some new device ids.

All have been in linux-next with no reported issues.

* tag 'usb-serial-6.2-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: xr: avoid requesting zero DTE rate
  USB: serial: cp210x: add support for B0 hangup
  USB: serial: cp210x: add Kamstrup RF sniffer PIDs
  USB: serial: option: add Quectel EM05-G modem

USB: serial: xr: avoid requesting zero DTE rate

2022-11-30T11:28:51+00:00

When the requested line speed is B0 (hangup) there is no need to use the
current speed in the line-coding request. This specifically avoids
requesting a zero DTE rate when the current speed is B0, which could
potentially confuse buggy firmware.

Reviewed-by: Greg Kroah-Hartman 
Signed-off-by: Johan Hovold

USB: serial: f81534: fix division by zero on line-speed change

2022-11-30T11:27:59+00:00

The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.

Fixes: 3aacac02f385 ("USB: serial: f81534: add high baud rate support")
Cc: stable@vger.kernel.org      # 4.16
Cc: Ji-Ze Hong (Peter Hong) 
Reviewed-by: Greg Kroah-Hartman 
Signed-off-by: Johan Hovold

USB: serial: f81232: fix division by zero on line-speed change

2022-11-30T11:27:44+00:00

The driver leaves the line speed unchanged in case a requested speed is
not supported. Make sure to handle the case where the current speed is
B0 (hangup) without dividing by zero when determining the clock source.

Fixes: 268ddb5e9b62 ("USB: serial: f81232: add high baud rate support")
Cc: stable@vger.kernel.org      # 5.2
Cc: Ji-Ze Hong (Peter Hong) 
Reviewed-by: Greg Kroah-Hartman 
Signed-off-by: Johan Hovold

USB: serial: cp210x: add support for B0 hangup

2022-11-30T06:37:12+00:00

A request to set the line speed to B0 is used to hang up a modem
connection by deasserting the modem control lines.

Note that there is no need reconfigure the line speed in hardware when
B0 is requested (even if some drivers do set it to an arbitrary value
for implementation or protocol reasons).

Reviewed-by: Alex Henrie 
Signed-off-by: Johan Hovold

USB: serial: cp210x: add Kamstrup RF sniffer PIDs

2022-11-28T09:36:50+00:00

The RF sniffers are based on cp210x where the RF frontends
are based on a different USB stack.

RF sniffers can analyze packets meta data including power level
and perform packet injection.

Can be used to perform RF frontend self-test when connected to
a concentrator, ex. arch/arm/boot/dts/imx7d-flex-concentrator.dts

Signed-off-by: Bruno Thomsen 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: option: add Quectel EM05-G modem

2022-11-25T09:39:09+00:00

The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:

"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM"  : MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0311 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0311 Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Duke Xin 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: option: add u-blox LARA-L6 modem

2022-11-16T16:19:43+00:00

Add LARA-L6 PIDs for three different USB compositions.

LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface

In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions

In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface

In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface

Signed-off-by: Davide Tronchin 
[ johan: drop PID defines in favour of comments ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: option: add u-blox LARA-R6 00B modem

2022-11-16T16:09:44+00:00

The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.

LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions

Signed-off-by: Davide Tronchin 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold