linux.git/drivers/usb/serial, branch v6.16

USB: serial: option: add Telit Cinterion FE910C04 (ECM) composition

2025-07-10T14:13:51+00:00

Add Telit Cinterion FE910C04 (ECM) composition:
0x10c7: ECM + tty (AT) + tty (AT) + tty (diag)

usb-devices output:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  7 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10c7 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FE910
S:  SerialNumber=f71b8b32
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Cc: stable@vger.kernel.org
Signed-off-by: Fabio Porcedda 
Signed-off-by: Johan Hovold

USB: serial: ftdi_sio: add support for NDI EMGUIDE GEMINI

2025-07-10T14:10:05+00:00

NDI (Northern Digital Inc.) is introducing a new product called the
EMGUIDE GEMINI that will use an FTDI chip for USB serial communications.
Add the NDI EMGUIDE GEMINI product ID that uses the NDI Vendor ID
rather than the FTDI Vendor ID, unlike older products.

Signed-off-by: Ryan Mann 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: option: add Foxconn T99W640

2025-06-24T08:45:43+00:00

T99W640 is designed based on Qualconn SDX72 chip. There are 3
serial ports to be enumerated: Diag, NMEA and AT.

Test evidence as below:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=0489 ProdID=e167 Rev=05.15
S:  Manufacturer=QCOM
S:  Product=SDXPINNL USB WWAN Adapter
S:  SerialNumber=cc1f1d92
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms

0&1: MBIM, 2:Modem, 3:GNSS(non-serial port), 4: NMEA, 5:Diag

Signed-off-by: Slark Xiao 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

treewide, timers: Rename from_timer() to timer_container_of()

2025-06-08T07:07:37+00:00

Move this API to the canonical timer_*() namespace.

[ tglx: Redone against pre rc1 ]

Signed-off-by: Ingo Molnar 
Signed-off-by: Thomas Gleixner 
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com

USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB

2025-05-21T15:19:55+00:00

Add new bcd (0x905) to support PL2303GT-2AB (TYPE_HXN).
Add new bcd (0x1005) to support PL2303GC-Q20 (TYPE_HXN).

Signed-off-by: Charles Yeh 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: bus: fix const issue in usb_serial_device_match()

2025-05-21T15:01:37+00:00

usb_serial_device_match() takes a const pointer, and then decides to
cast it away into a non-const one, which is not a good thing to do
overall.  Fix this up by properly setting the pointers to be const to
preserve that attribute.

Fixes: d69d80484598 ("driver core: have match() callback in struct bus_type take a const *")
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Johan Hovold

USB: serial: ti_usb_3410_5052: drop bogus read urb check

2025-05-05T12:25:59+00:00

The read urb pointer is dereferenced before checking that it is non-NULL
during open(), but no check is needed as the existence of a bulk in
endpoint is verified during attach() since commit ef079936d3cd ("USB:
serial: ti_usb_3410_5052: fix NULL-deref at open").

Drop the bogus read urb sanity check.

Signed-off-by: Johan Hovold

USB: serial: simple: add OWON HDS200 series oscilloscope support

2025-04-16T06:38:22+00:00

Add serial support for OWON HDS200 series oscilloscopes and likely
many other pieces of OWON test equipment.

OWON HDS200 series devices host two USB endpoints, designed to
facilitate bidirectional SCPI. SCPI is a predominately ASCII text
protocol for test/measurement equipment. Having a serial/tty interface
for these devices lowers the barrier to entry for anyone trying to
write programs to communicate with them.

The following shows the USB descriptor for the OWON HDS272S running
firmware V5.7.1:

Bus 001 Device 068: ID 5345:1234 Owon PDS6062T Oscilloscope
Negotiated speed: Full Speed (12Mbps)
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 [unknown]
  bDeviceSubClass         0 [unknown]
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x5345 Owon
  idProduct          0x1234 PDS6062T Oscilloscope
  bcdDevice            1.00
  iManufacturer           1 oscilloscope
  iProduct                2 oscilloscope
  iSerial                 3 oscilloscope
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0029
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         5 Physical Interface Device
      bInterfaceSubClass      0 [unknown]
      bInterfaceProtocol      0
      iInterface              0
      ** UNRECOGNIZED:  09 21 11 01 00 01 22 5f 00
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              32
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              32
Device Status:     0x0000
  (Bus Powered)

OWON appears to be using the same USB Vendor and Product ID for many
of their oscilloscopes. Looking at the discussion about the USB
vendor/product ID, in the link bellow, suggests that this VID/PID is
shared with VDS, SDS, PDS, and now the HDS series oscilloscopes.
Available documentation for these devices seems to indicate that all
use a similar SCPI protocol, some with RS232 options. It is likely that
this same simple serial setup would work correctly for them all.

Link: https://usb-ids.gowdy.us/read/UD/5345/1234
Signed-off-by: Craig Hesling 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: ftdi_sio: add support for Abacus Electrics Optical Probe

2025-04-16T06:38:20+00:00

Abacus Electrics makes optical probes for interacting with smart meters
over an optical interface.

At least one version uses an FT232B chip (as detected by ftdi_sio) with
a custom USB PID, which needs to be added to the list to make the device
work in a plug-and-play fashion.

Signed-off-by: Michael Ehrenreich 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold

USB: serial: option: add Sierra Wireless EM9291

2025-04-16T06:38:08+00:00

Add Sierra Wireless EM9291.

Interface 0: MBIM control
          1: MBIM data
          3: AT port
          4: Diagnostic port

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1199 ProdID=90e3 Rev=00.06
S:  Manufacturer=Sierra Wireless, Incorporated
S:  Product=Sierra Wireless EM9291
S:  SerialNumber=xxxxxxxxxxxxxxxx
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Adam Xue 
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold