Pull USB patches from Greg Kroah-Hartman: "Here's the big USB pull request for 3.10-rc1. Lots of USB patches here, the majority being USB gadget changes and USB-serial driver cleanups, the rest being ARM build fixes / cleanups, and individual driver updates. We also finally got some chipidea fixes, which have been delayed for a number of kernel releases, as the maintainer has now reappeared. All of these have been in linux-next for a while" * tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits) USB: ehci-msm: USB_MSM_OTG needs USB_PHY USB: OHCI: avoid conflicting platform drivers USB: OMAP: ISP1301 needs USB_PHY USB: lpc32xx: ISP1301 needs USB_PHY USB: ftdi_sio: enable two UART ports on ST Microconnect Lite usb: phy: tegra: don't call into tegra-ehci directly usb: phy: phy core cannot yet be a module USB: Fix initconst in ehci driver usb-storage: CY7C68300A chips do not support Cypress ATACB USB: serial: option: Added support Olivetti Olicard 145 USB: ftdi_sio: correct ST Micro Connect Lite PIDs ARM: mxs_defconfig: add CONFIG_USB_PHY ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY usb: phy: remove exported function from __init section usb: gadget: zero: put function instances on unbind usb: gadget: f_sourcesink.c: correct a copy-paste misnomer usb: gadget: cdc2: fix error return code in cdc_do_config() usb: gadget: multi: fix error return code in rndis_do_config() usb: gadget: f_obex: fix error return code in obex_bind() USB: storage: convert to use module_usb_driver() ...
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports. The first two ports are reserved for the JTAG interface. We enable by default ports 2 and 3 as UARTs (where port 2 is a conventional RS-232 UART) Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds PID for Olivetti Olicard 145 in option.c Signed-off-by: Filippo Turato <nnj7585@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB UART FTDI chip. It is also possible to drive STM reference targets populated with an on-board JTAG debugger based on the FT2232H chip with the same STMicroelectronics tools. For this reason, the ST Micro Connect Lite PIDs should be ST_STMCLT_2232_PID: 0x3746 ST_STMCLT_4232_PID: 0x3747 Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty-layer handle it instead. Note that the port drain-delay is set to three characters to keep the 20ms delay after wait_until_sent at low baudrates (1200 baud) during close. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant drain, which has already been handled by the tty-layer, from break_ctl. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be empty. This is needed to make the tty layer wait for hardware buffers to drain on close. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line status register is only polled so let's not keep a possibly outdated value in the port data. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from ti_drain to close where it belongs. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant wait_until_sent, which has already been handled by the tty-layer, from break_ctl. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>