linux.git/drivers/usb/serial/option.c, branch v3.14

USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8

2014-02-18T20:04:41+00:00

This interface is to be handled by the qmi_wwan driver.

CC: Hans-Christoph Schemmel 
CC: Christian Schmiedl 
CC: Nicolaus Colberg 
CC: David McCullough 
Signed-off-by: Aleksander Morgado 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: option: blacklist ZTE MF667 net interface

2014-02-11T23:33:54+00:00

Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.

Signed-off-by: Raymond Wanyoike 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: serial: add support for iBall 3.5G connect usb modem

2014-01-03T20:40:22+00:00

Add support for iBall 3.5G connect usb modem.

$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY

$usb-devices
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9605 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Signed-off-by: Rahul Bedarkar 
Suggested-by: Bjørn Mork 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

Merge 3.13-rc5 into usb-next

2013-12-24T18:18:03+00:00

This resolves the merge issue with drivers/usb/host/ohci-at91.c

Signed-off-by: Greg Kroah-Hartman

usb: option: add new zte 3g modem pids to option driver

2013-12-19T00:29:43+00:00

Signed-off-by: Jun zhang 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: serial: zte_ev: move support for ZTE AC2726 from zte_ev back to option

2013-12-09T21:14:12+00:00

ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.

Signed-off-by: Dmitry Kunilov 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: option: support new huawei devices

2013-12-02T21:51:02+00:00

Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.

Signed-off-by: fangxiaozhi 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: serial: option: blacklist interface 1 for Huawei E173s-6

2013-12-02T21:50:54+00:00

Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:

tty_release: ttyUSB1: read/write wait queue active!

It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.

Signed-off-by: Gustavo Zacarias 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB：add new zte 3g-dongle's pid to option.c

2013-10-25T05:37:25+00:00

Signed-off-by: Rui li 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usb: serial: option: blacklist Olivetti Olicard200

2013-10-16T20:24:39+00:00

Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.

Signed-off-by: Enrico Mioso 
Signed-off-by: Antonella Pellizzari 
Tested-by: Dan Williams 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman