* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
  EHCI: fix direction handling for interrupt data toggles
  USB: serial: add IDs for WinChipHead USB->RS232 adapter
  USB: OHCI: fix another regression for NVIDIA controllers
  usb: gadget: m66592-udc: add pullup function
  usb: gadget: m66592-udc: add function for external controller
  usb: gadget: r8a66597-udc: add pullup function
  usb: renesas_usbhs: support multi driver
  usb: renesas_usbhs: inaccessible pipe is not an error
  usb: renesas_usbhs: care buff alignment when dma handler
  USB: PL2303: correctly handle baudrates above 115200
  usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
  usb: renesas_usbhs: compile/config are rescued
  usb: renesas_usbhs: fixup comment-out
  usb: update email address in ohci-sh and r8a66597-hcd
  usb: r8a66597-hcd: add function for external controller
  EHCI: only power off port if over-current is active
  USB: mon: Allow to use usbmon without debugfs
  USB: EHCI: go back to using the system clock for QH unlinks
  ehci: add pci quirk for Ordissimo and RM Slate 100 too
  ehci: refactor pci quirk to use standard dmi_check_system method
  ...

Fix up trivial conflicts in Documentation/feature-removal-schedule.txt

This patch (as1480) fixes a rather obscure bug in ehci-hcd.  The
qh_update() routine needs to know the number and direction of the
endpoint corresponding to its QH argument.  The number can be taken
directly from the QH data structure, but the direction isn't stored
there.  The direction is taken instead from the first qTD linked to
the QH.

However, it turns out that for interrupt transfers, qh_update() gets
called before the qTDs are linked to the QH.  As a result, qh_update()
computes a bogus direction value, which messes up the endpoint toggle
handling.  Under the right combination of circumstances this causes
usb_reset_endpoint() not to work correctly, which causes packets to be
dropped and communications to fail.

Now, it's silly for the QH structure not to have direct access to all
the descriptor information for the corresponding endpoint.  Ultimately
it may get a pointer to the usb_host_endpoint structure; for now,
adding a copy of the direction flag solves the immediate problem.

This allows the Spyder2 color-calibration system (a low-speed USB
device that sends all its interrupt data packets with the toggle set
to 0 and hance requires constant use of usb_reset_endpoint) to work
when connected through a high-speed hub.  Thanks to Graeme Gill for
supplying the hardware that allowed me to track down this bug.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Graeme Gill <graeme@argyllcms.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The NVIDIA series of OHCI controllers continues to be troublesome.  A
few people using the MCP67 chipset have reported that even with the
most recent kernels, the OHCI controller fails to handle new
connections and spams the system log with "unable to enumerate USB
port" messages.  This is different from the other problems previously
reported for NVIDIA OHCI controllers, although it is probably related.

It turns out that the MCP67 controller does not like to be kept in the
RESET state very long.  After only a few seconds, it decides not to
work any more.  This patch (as1479) changes the PCI initialization
quirk code so that NVIDIA controllers are switched into the SUSPEND
state after 50 ms of RESET.  With no interrupts enabled and all the
downstream devices reset, and thus unable to send wakeup requests,
this should be perfectly safe (even for non-NVIDIA hardware).

The removal code in ohci-hcd hasn't been changed; it will still leave
the controller in the RESET state.  As a result, if someone unloads
ohci-hcd and then reloads it, the controller won't work again until
the system is rebooted.  If anybody complains about this, the removal
code can be updated similarly.

This fixes Bugzilla #22052.

Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Sync with Linus' tree to be able to apply pending patches that
are based on newer code already present upstream.

This is typo fix of
749da5f8 (USB: straighten out port feature vs. port status usage)

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

MAX4967 USB power supply chip we use on our boards signals over-current when
power is not enabled; once it's enabled, over-current signal returns to normal.
That unfortunately caused the endless stream of "over-current change on port"
messages. The EHCI root hub code reacts on every over-current signal change
with powering off the port -- such change event is generated the moment the
port power is enabled, so once enabled the power is immediately cut off.
I think we should only cut off power when we're seeing the active over-current
signal, so I'm adding such check to that code. I also think that the fact that
we've cut off the port power should be reflected in the result of GetPortStatus
request immediately, hence I'm adding a PORTSCn register readback after write...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1477) fixes a problem affecting a few types of EHCI
controller.  Contrary to what one might expect, these controllers
automatically stop their internal frame counter when no ports are
enabled.  Since ehci-hcd currently relies on the frame counter for
determining when it should unlink QHs from the async schedule, those
controllers run into trouble: The frame counter stops and the QHs
never get unlinked.

Some systems have also experienced other problems traced back to
commit b963801164618e25fbdc0cd452ce49c3628b46c8 (USB: ehci-hcd unlink
speedups), which made the original switch from using the system clock
to using the frame counter.  It never became clear what the reason was
for these problems, but evidently it is related to use of the frame
counter.

To fix all these problems, this patch more or less reverts that commit
and goes back to using the system clock.  But this can't be done
cleanly because other changes have since been made to the scan_async()
subroutine.  One of these changes involved the tricky logic that tries
to avoid rescanning QHs that have already been seen when the scanning
loop is restarted, which happens whenever an URB is given back.
Switching back to clock-based unlinks would make this logic even more
complicated.

Therefore the new code doesn't rescan the entire async list whenever a
giveback occurs.  Instead it rescans only the current QH and continues
on from there.  This requires the use of a separate pointer to keep
track of the next QH to scan, since the current QH may be unlinked
while the scanning is in progress.  That new pointer must be global,
so that it can be adjusted forward whenever the _next_ QH gets
unlinked.  (uhci-hcd uses this same trick.)

Simplification of the scanning loop removes a level of indentation,
which accounts for the size of the patch.  The amount of code changed
is relatively small, and it isn't exactly a reversion of the
b963801164 commit.

This fixes Bugzilla #32432.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Tested-by: Matej Kenda <matejken@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add another variant of the Pegatron tablet used by Ordissimo, and
apparently RM Slate 100, to the list of models that should skip the
negociation for the handoff of the EHCI controller.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>