linux.git/drivers/usb/dwc3, branch v5.5

usb: dwc3: gadget: Fix request complete check

2019-12-30T18:54:58+00:00

We can only check for IN direction if the request had completed. For OUT
direction, it's perfectly fine that the host can send less than the
setup length. Let's return true fall all cases of OUT direction.

Fixes: e0c42ce590fe ("usb: dwc3: gadget: simplify IOC handling")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen 
Link: https://lore.kernel.org/r/ac5a3593a94fdaa3d92e6352356b5f7a01ccdc7c.1576291140.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: pci: add ID for the Intel Comet Lake -H variant

2019-12-12T13:02:37+00:00

The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.

Signed-off-by: Heikki Krogerus 
Acked-by: Felipe Balbi 
Cc: stable 
Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: ep0: Clear started flag on completion

2019-12-10T12:52:41+00:00

Clear ep0's DWC3_EP_TRANSFER_STARTED flag if the END_TRANSFER command is
completed. Otherwise, we can't start control transfer again after
END_TRANSFER.

Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen 
Signed-off-by: Felipe Balbi

usb: dwc3: gadget: Clear started flag for non-IOC

2019-12-10T12:52:41+00:00

Normally the END_TRANSFER command completion handler will clear the
DWC3_EP_TRANSFER_STARTED flag. However, if the command was sent without
interrupt on completion, then the flag will not be cleared. Make sure to
clear the flag in this case.

Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen 
Signed-off-by: Felipe Balbi

usb: dwc3: gadget: Fix logical condition

2019-12-10T12:52:41+00:00

This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.

Fixes: f38e35dd84e2 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")

Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar 
Signed-off-by: Felipe Balbi

usb: dwc3: Fix Kconfig indentation

2019-11-21T13:39:39+00:00

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
	$ sed -e 's/^        /\t/' -i */Kconfig

Signed-off-by: Krzysztof Kozlowski 
Link: https://lore.kernel.org/r/20191121132914.29368-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

2019-11-18T07:24:12+00:00

Felipe writes:

USB: changes for v5.5

We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.

Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.

* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
  usb: dwc3: of-simple: add a shutdown
  usb: cdns3: Add TI specific wrapper driver
  dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
  usb: mtu3: fix race condition about delayed_status
  usb: gadget: Add UDC driver for tegra XUSB device mode controller
  usb: dwc3: debug: Remove newline printout
  usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
  usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
  USB: gadget: udc: clean up an indentation issue
  usb: gadget: Quieten gadget config message
  phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
  usb: gadget: Remove set but not used variable 'opts' in msg_do_config
  usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
  usb: mtu3: add a new function to do status stage
  usb: gadget: configfs: fix concurrent issue between composite APIs
  usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
  usb: gadget: Correct NULL pointer checking in fsl gadget
  usb: fsl: Remove unused variable
  USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
  USB: dummy-hcd: increase max number of devices to 32
  ...

usb: dwc3: create debugfs directory under usb root

2019-11-14T03:14:54+00:00

Now the USB gadget subsystem can use the USB debugfs root directory,
so move dwc3's directory from the root of the debugfs filesystem into
the root of usb

Signed-off-by: Chunfeng Yun 
Link: https://lore.kernel.org/r/1573541519-28488-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman

Merge 5.4-rc6 into usb-next

2019-11-04T05:41:09+00:00

We need the USB fixes in here to build on top of.

Signed-off-by: Greg Kroah-Hartman

usb: dwc3: gadget: fix race when disabling ep with cancelled xfers

2019-10-31T17:57:54+00:00

When disabling an endpoint which has cancelled requests, we should
make sure to giveback requests that are currently pending in the
cancelled list, otherwise we may fall into a situation where command
completion interrupt fires after endpoint has been disabled, therefore
causing a splat.

Fixes: fec9095bdef4 "usb: dwc3: gadget: remove wait_end_transfer"
Reported-by: Roger Quadros 
Signed-off-by: Felipe Balbi 
Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.com
Signed-off-by: Greg Kroah-Hartman