linux.git/drivers/usb/dwc3, branch v4.15

usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3

2017-12-11T10:35:37+00:00

For isochronous endpoints with ep->mult less than 3, PCM1 value of
trb->size in set incorrectly.
For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is
set to -2. This is because the initial mult is set to ep->mult - 1
instead of 2.

Signed-off-by: Manu Gautam 
Signed-off-by: Felipe Balbi

usb: dwc3: of-simple: set dev_pm_ops

2017-12-11T10:35:36+00:00

dwc3_of_simple_dev_pm_ops has never been used since the initial support
by commit 16adc674d0d6 ("usb: dwc3: add generic OF glue layer").

I guess it just missed to set .pm struct member.

Signed-off-by: Masahiro Yamada 
Signed-off-by: Felipe Balbi

usb: dwc3: of-simple: fix missing clk_disable_unprepare

2017-12-11T10:35:36+00:00

If of_clk_get() fails, the clean-up of already initialized clocks should be
the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare()
for each clock should be called before the clk_put().

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 16adc674d0d6 ("usb: dwc3: ep0: fix setup_packet_pending initialization")

Signed-off-by: Andreas Platschek 
Signed-off-by: Felipe Balbi

usb: dwc3: gadget: Wait longer for controller to end command processing

2017-12-11T10:35:36+00:00

DWC3_DEPCMD_ENDTRANSFER has been witnessed to require around 600 iterations
before controller would become idle again after unplugging the USB cable
with AIO reads submitted.
Bump timeout from 500 iterations to 1000 so dwc3_stop_active_transfer does
not receive -ETIMEDOUT and does not WARN:

[   81.326273] ------------[ cut here ]------------
[   81.335341] WARNING: CPU: 0 PID: 1874 at drivers/usb/dwc3/gadget.c:2627 dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3]
[   81.347094] Modules linked in: usb_f_fs libcomposite configfs bnep btsdio bluetooth ecdh_generic brcmfmac brcmutil dwc3 intel_powerclamp coretemp ulpi kvm_intel udc_core kvm irqbypass crc32_pclmul crc32c_intel pcbc dwc3_pci aesni_intel aes_i586 crypto_simd cryptd ehci_pci ehci_hcd basincove_gpadc industrialio gpio_keys usbcore usb_common
[   81.378142] CPU: 0 PID: 1874 Comm: irq/34-dwc3 Not tainted 4.14.0-edison+ #119
[   81.385545] Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
[   81.394548] task: f5b1be00 task.stack: f420a000
[   81.399219] EIP: dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3]
[   81.406086] EFLAGS: 00010086 CPU: 0
[   81.409672] EAX: 0000001f EBX: f5729800 ECX: c132a2a2 EDX: 00000000
[   81.416096] ESI: f4054014 EDI: f41cf400 EBP: f420be10 ESP: f420bdf4
[   81.422521]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[   81.428061] CR0: 80050033 CR2: b7a3f000 CR3: 01d94000 CR4: 001006d0
[   81.434483] Call Trace:
[   81.437063]  __dwc3_gadget_ep_disable+0xa3/0x2b0 [dwc3]
[   81.442438]  ? _raw_spin_lock_irqsave+0x32/0x40
[   81.447135]  dwc3_gadget_ep_disable+0xbf/0xe0 [dwc3]
[   81.452269]  usb_ep_disable+0x1c/0xd0 [udc_core]
[   81.457048]  ffs_func_eps_disable.isra.15+0x3b/0x90 [usb_f_fs]
[   81.463070]  ffs_func_set_alt+0x7d/0x310 [usb_f_fs]
[   81.468132]  ffs_func_disable+0x14/0x20 [usb_f_fs]
[   81.473075]  reset_config+0x5b/0x90 [libcomposite]
[   81.478023]  composite_disconnect+0x2b/0x50 [libcomposite]
[   81.483685]  dwc3_disconnect_gadget+0x39/0x50 [dwc3]
[   81.488808]  dwc3_gadget_disconnect_interrupt+0x21b/0x250 [dwc3]
[   81.495014]  dwc3_thread_interrupt+0x2a8/0xf70 [dwc3]
[   81.500219]  ? __schedule+0x78c/0x7e0
[   81.504027]  irq_thread_fn+0x18/0x30
[   81.507715]  ? irq_thread+0xb7/0x180
[   81.511400]  irq_thread+0x111/0x180
[   81.515000]  ? irq_finalize_oneshot+0xe0/0xe0
[   81.519490]  ? wake_threads_waitq+0x30/0x30
[   81.523806]  kthread+0x107/0x110
[   81.527131]  ? disable_percpu_irq+0x50/0x50
[   81.531439]  ? kthread_stop+0x150/0x150
[   81.535397]  ret_from_fork+0x19/0x24
[   81.539136] Code: 89 d8 c7 45 ec 00 00 00 00 c7 45 f0 00 00 00 00 c7 45 f4 00 00 00 00 e8 56 ef ff ff 85 c0 74 12 50 68 b9 1c 14 f8 e8 64 0f f7 c8 <0f> ff 58 5a 8d 76 00 8b 83 98 00 00 00 c6 83 a0 00 00 00 00 83
[   81.559295] ---[ end trace f3133eec81a473b8 ]---

Number of iterations measured on 4 consecutive unplugs:
[ 1088.799777] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 605 times
[ 1222.024986] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 580 times
[ 1317.590452] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 598 times
[ 1453.218314] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 594 times

Signed-off-by: Vincent Pelletier 
Signed-off-by: Felipe Balbi

Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2017-11-14T05:14:07+00:00

Pull USB/PHY updates from Greg KH:
 "Here is the big set of USB and PHY driver updates for 4.15-rc1.

  There is the usual amount of gadget and xhci driver updates, along
  with phy and chipidea enhancements. There's also a lot of SPDX tags
  and license boilerplate cleanups as well, which provide some churn in
  the diffstat.

  Other major thing is the typec code that moved out of staging and into
  the "real" part of the drivers/usb/ tree, which was nice to see
  happen.

  All of these have been in linux-next with no reported issues for a
  while"

* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
  usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
  USB: usbfs: compute urb->actual_length for isochronous
  usb: core: message: remember to reset 'ret' to 0 when necessary
  USB: typec: Remove remaining redundant license text
  USB: typec: add SPDX identifiers to some files
  USB: renesas_usbhs: rcar?.h: add SPDX tags
  USB: chipidea: ci_hdrc_tegra.c: add SPDX line
  USB: host: xhci-debugfs: add SPDX lines
  USB: add SPDX identifiers to all remaining Makefiles
  usb: host: isp1362-hcd: remove a couple of redundant assignments
  USB: adutux: remove redundant variable minor
  usb: core: add a new usb_get_ptm_status() helper
  usb: core: add a 'type' parameter to usb_get_status()
  usb: core: introduce a new usb_get_std_status() helper
  usb: core: rename usb_get_status() 'type' argument to 'recip'
  usb: core: add Status Type definitions
  USB: gadget: Remove redundant license text
  USB: gadget: function: Remove redundant license text
  USB: gadget: udc: Remove redundant license text
  USB: gadget: legacy: Remove redundant license text
  ...

USB: dwc3: Remove redundant license text

2017-11-07T14:45:01+00:00

Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Cc: Kukjin Kim 
Cc: Krzysztof Kozlowski 
Cc: Patrice Chotard 
Acked-by: Felipe Balbi 
Signed-off-by: Greg Kroah-Hartman

USB: add SPDX identifiers to all remaining files in drivers/usb/

2017-11-04T10:48:02+00:00

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner 
Cc: Kate Stewart 
Cc: Philippe Ombredanne 
Signed-off-by: Greg Kroah-Hartman 
Acked-by: Felipe Balbi 
Acked-by: Johan Hovold 
Signed-off-by: Greg Kroah-Hartman

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55+00:00

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart 
Reviewed-by: Philippe Ombredanne 
Reviewed-by: Thomas Gleixner 
Signed-off-by: Greg Kroah-Hartman

usb: dwc3: core: Notify current USB mode to USB3 PHY as well

2017-10-24T09:51:20+00:00

Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.

Signed-off-by: Manu Gautam 
Signed-off-by: Felipe Balbi

usb: dwc3: pci: Runtime resume child device from wq

2017-10-24T09:51:19+00:00

Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.

Signed-off-by: Manu Gautam 
Signed-off-by: Felipe Balbi