linux.git/drivers/usb/dwc2, branch v5.16

usb: dwc2: fix STM ID/VBUS detection startup delay in dwc2_driver_probe

2021-12-15T17:43:24+00:00

When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.

Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable 
Acked-by: Minas Harutyunyan 
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: hcd_queue: Fix use of floating point literal

2021-11-17T14:03:34+00:00

A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).

 drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires  'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
                         delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
                                             ^
 drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
 #define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
                                 ^
 1 error generated.

This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.

There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.

Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: https://github.com/llvm/llvm-project/commit/a8083d42b1c346e21623a1d36d1f0cadd7801d83
Fixes: 6ed30a7d8ec2 ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable 
Reviewed-by: Nick Desaulniers 
Reviewed-by: John Keeping 
Acked-by: Minas Harutyunyan 
Signed-off-by: Nathan Chancellor 
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: gadget: Fix ISOC flow for elapsed frames

2021-11-17T14:02:11+00:00

Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.

Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.

Fixes: 91bb163e1e4f ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable 
Reviewed-by: John Keeping 
Signed-off-by: Minas Harutyunyan 
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: stm32mp15: set otg_rev

2021-10-25T07:20:26+00:00

STM32MP15 complies with the OTG 2.0. Set OTG revision accordingly. It is
useful for the of_usb_update_otg_caps() routine to check and update
otg_rev to the lower value between DT and provided params.

Signed-off-by: Fabrice Gasnier 
Link: https://lore.kernel.org/r/1634133425-25670-5-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: add otg_rev and otg_caps information for gadget driver

2021-10-25T07:20:26+00:00

Currently the dwc2 doesn't fill in the 'otg_caps' of usb_gadget structure.
When registering a gadget device (e.g. via configfs), the
usb_otg_descriptor_init() checks the 'otg_caps' and 'otg_rev'. It defaults
to HNP and SRP bmAttributes if unspecified. There may be a mismatch with
what's being set in dwc2 params structure. This result in the descriptors
to be miss-configured in this case.

So replace 'otg_cap' bit field by 'otg_caps' structure, so hnp, srp and
otg_rev' can be configured directly in the params.
It's then provided to the gadget struct. These parameters can be tuned
for each platform. In case it's not set, it will default to current
behavior.

Also add option to setup these from the device tree by calling
of_usb_update_otg_caps(). This provides support for standard properties
such as "otg-rev", "hnp-disable" and "srp-disable" (see usb-drd.yaml).

Signed-off-by: Fabrice Gasnier 
Link: https://lore.kernel.org/r/1634133425-25670-4-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: drd: reset current session before setting the new one

2021-10-21T10:49:01+00:00

If role is changed without the "none" step, A- and B- valid session could
be set at the same time. It is an issue.
This patch resets A-session if role switch sets B-session, and resets
B-session if role switch sets A-session.
Then, it is possible to change the role without the "none" step.

Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan 
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211005095305.66397-4-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: drd: fix dwc2_drd_role_sw_set when clock could be disabled

2021-10-21T10:49:00+00:00

In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.

Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan 
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: drd: fix dwc2_force_mode call in dwc2_ovr_init

2021-10-21T10:49:00+00:00

Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c

When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.

Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan 
Signed-off-by: Amelie Delaunay 
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: gadget: Fix ISOC transfer complete handling for DDMA

2021-09-14T08:42:00+00:00

When last descriptor in a descriptor list completed with XferComplete
interrupt, core switching to handle next descriptor and assert BNA
interrupt. Both these interrupts are set while dwc2_hsotg_epint()
handler called. Each interrupt should be handled separately: first
XferComplete interrupt then BNA interrupt, otherwise last completed
transfer will not be giveback to function driver as completed
request.

Fixes: 729cac693eec ("usb: dwc2: Change ISOC DDMA flow")
Cc: stable 
Signed-off-by: Minas Harutyunyan 
Link: https://lore.kernel.org/r/a36981accc26cd674c5d8f8da6164344b94ec1fe.1631386531.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman

usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave

2021-09-14T08:35:10+00:00

According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.

Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.

This fix complete requests with -ENODATA if interval elapsed.

HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).

As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.

Tested by internal tool which also using for dwc3 testing.

Signed-off-by: Minas Harutyunyan 
Cc: stable 
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman