linux.git/drivers/usb/dwc2/params.c, branch v4.18 Linux kernel source tree usb: dwc2: gadget: Fix coverity issue 2018-05-21T07:40:16+00:00 Grigor Tovmasyan Grigor.Tovmasyan@synopsys.com 2018-04-03T11:22:25+00:00 47265c067c0d129f3a0e94bc221293a780af9d78 When _param is unsigned and the minimum value of range is 0, it gives the following warning: COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value is never true. Converting ._param to int to avoid this warning. Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.

Converting ._param to int to avoid this warning.

Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Fix HiKey regression caused by power_down feature 2018-05-21T07:35:46+00:00 John Stultz john.stultz@linaro.org 2018-05-19T00:49:03+00:00 d98c624ab3bf9c3c988c3b7d0f24e703061a172f In 4.17-rc, commit 03ea6d6e9e1f ("usb: dwc2: Enable power down") caused the HiKey board to not correctly handle switching between usb-gadget and usb-host mode. Unplugging the OTG port would result in: [ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore [ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers And the USB-host ports would not function. And plugging in the OTG port, we would see: [ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0 [ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231 [ 46.055767] Hardware name: HiKey Development Board (DT) [ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change ... Thus, this patch sets the hisi params to disable the power_down flag by default, and gets thing working again. Cc: John Youn <johnyoun@synopsys.com> Cc: Vardan Mikayelyan <mvardan@synopsys.com> Cc: Artur Petrosyan <arturp@synopsys.com> Cc: Grigor Tovmasyan <tovmasya@synopsys.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: linux-usb@vger.kernel.org Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
In 4.17-rc, commit 03ea6d6e9e1f ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.

Unplugging the OTG port would result in:
[   42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[   42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers

And the USB-host ports would not function.

And plugging in the OTG port, we would see:
[   46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[   46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[   46.055767] Hardware name: HiKey Development Board (DT)
[   46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...

Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.

Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Fix kernel doc's warnings. 2018-05-21T07:02:13+00:00 Grigor Tovmasyan Grigor.Tovmasyan@synopsys.com 2018-05-16T08:04:24+00:00 6fb914d788133fd2298af87c50aefe1863cf1445 Added descriptions for all not described parameters. Fix all kernel doc's warnings. Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Add Interpacket Gap(IPG) feature support 2018-05-15T07:16:47+00:00 Grigor Tovmasyan Grigor.Tovmasyan@synopsys.com 2018-05-05T08:17:58+00:00 b43ebc96e985fed9417c6aff769a6839bdaa6cdf Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED bits definitions to enable/disable IPG feature. Added ipg_isoc_en core parameter which will indicate IPG support enable/disable and initialize it. Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.

Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.

Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing 2018-03-23T12:33:09+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2018-03-23T12:33:09+00:00 6d23ee9caa6790aea047f9aca7f3c03cb8d96eb6 Felipe writes: usb: changes for v4.17 merge window Quite a lot happened in this cycle, with a total of 95 non-merge commits. The most interesting parts are listed below: Synopsys has been adding better support for USB 3.1 to dwc3. The same series also sets g_mass_storage's max speed to SSP. Roger Quadros (TI) added support for dual-role using the OTG block available in some dwc3 implementations, this makes sure that AM437x can swap roles in runtime. We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to the work of Martin Blumenstingl. We also have a ton of changes in dwc2 (51% of all changes, in fact). The most interesting part there is the support for Hibernation (a Synopsys PM feature). Apart from these, we have our regular set of non-critical fixes all over the place. 
Felipe writes:

usb: changes for v4.17 merge window

Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:

Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.

Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.

We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.

We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).

Apart from these, we have our regular set of non-critical fixes all
over the place.
usb: dwc2: Force mode optimizations 2018-03-13T08:47:58+00:00 Vardan Mikayelyan mvardan@synopsys.com 2018-02-16T08:56:03+00:00 13b1f8e25bfd1d6b96278421f934efdd35be9d5b If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during driver probe to get the host and device specific HW parameters. Then we clear the force mode bits so that the core operates in OTG mode. The force mode bits should not be touched at any other time during the driver lifetime and they should be preserved whenever the GUSBCFG register is written to. The force mode bit values will persist across soft resets of the core. If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the force mode is set just once at probe to configure the core as either a host or peripheral. Given the above, we no longer need any other reset delays, force delays, or any forced modes anywhere else in the driver. So replace all calls to dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove all other unnecessary delays. Also remove the dwc2_force_mode_if_needed() function since the "if needed" part is already taken care of by the polling in dwc2_force_mode(). Finally, remove all other calls to dwc2_clear_force_mode(). Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.

The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.

If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.

Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.

Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().

Finally, remove all other calls to dwc2_clear_force_mode().

Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Enable power down 2018-03-13T08:47:57+00:00 John Youn johnyoun@synopsys.com 2018-02-16T10:12:28+00:00 03ea6d6e9e1ff1b0222eb723eee5990d3511cc4d Enable the power down option based on the core capability. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: Artur Petrosyan <arturp@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
Enable the power down option based on the core capability.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Add hibernation field into dwc2_hw_params 2018-03-13T08:47:53+00:00 Vardan Mikayelyan mvardan@synopsys.com 2018-02-16T10:07:05+00:00 631a23108c1a90b726ca99f1f90d48a91737f43d Add parameter and it's initialization, needed for hibernation. Reimplement dwc2_set_param_power_down() to support hibernation too. Now 'power_down' parameter can be initialized with 0, 1 or 2. 0 - No 1 - Partial power down 2 - Hibernation Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
Add parameter and it's initialization, needed for hibernation.

Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation

Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Rename hibernation to partial_power_down 2018-03-13T08:47:53+00:00 Vardan Mikayelyan mvardan@synopsys.com 2018-02-16T10:06:36+00:00 41ba9b9b95beb8bb101a40c6badbbe49da6af9cd No-op change, only rename. This code was misnamed originally. It was only responsible for partial power down and not for hibernation. Rename core_params->hibernation to core_params->power_down, dwc2_set_param_hibernation() to dwc2_set_param_power_down(). Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
No-op change, only rename.

This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.

Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().

Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb: dwc2: Add core parameters for LPM support 2018-03-13T08:47:47+00:00 Sevak Arakelyan sevaka@synopsys.com 2018-01-24T13:41:48+00:00 6f80b6de0ecf65077b53c86967c714d42f4299e0 Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold core parameters. These will indicate LPM and LPM Errata support as well as chosen L1 sleeping mode for the core and PHY. Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com> Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> 
Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.

Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>