This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.

Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.

This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.

Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110

Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[  206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[  206.143691] usb 3-2.4: device descriptor read/64, error -32
[  206.351671] usb 3-2.4: device descriptor read/64, error -32

Info for this hub:
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev=01.11
S:  Product=USB 2.0 Hub
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.

Hence wait for extra delay, if the device is connected to this quirky
hub.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull USB/PHY updates from Greg KH:
 "Here is the big USB/PHY driver patches for 4.20-rc1

  Lots of USB changes in here, primarily in these areas:

   - typec updates and new drivers

   - new PHY drivers

   - dwc2 driver updates and additions (this old core keeps getting
     added to new devices.)

   - usbtmc major update based on the industry group coming together and
     working to add new features and performance to the driver.

   - USB gadget additions for new features

   - USB gadget configfs updates

   - chipidea driver updates

   - other USB gadget updates

   - USB serial driver updates

   - renesas driver updates

   - xhci driver updates

   - other tiny USB driver updates

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
  usb: phy: ab8500: silence some uninitialized variable warnings
  usb: xhci: tegra: Add genpd support
  usb: xhci: tegra: Power-off power-domains on removal
  usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
  usbip: tools: fix atoi() on non-null terminated string
  USB: misc: appledisplay: fix backlight update_status return code
  phy: phy-pxa-usb: add a new driver
  usb: host: add DT bindings for faraday fotg2
  usb: host: ohci-at91: fix request of irq for optional gpio
  usb/early: remove set but not used variable 'remain_length'
  usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
  usb: typec: tcpm: Report back negotiated PPS voltage and current
  USB: core: remove set but not used variable 'udev'
  usb: core: fix memory leak on port_dev_path allocation
  USB: net2280: Remove ->disconnect() callback from net2280_pullup()
  usb: dwc2: disable power_down on rockchip devices
  usb: gadget: udc: renesas_usb3: add support for r8a77990
  dt-bindings: usb: renesas_usb3: add bindings for r8a77990
  usb: gadget: udc: renesas_usb3: Add r8a774a1 support
  USB: serial: cypress_m8: remove set but not used variable 'iflag'
  ...

Pull siginfo updates from Eric Biederman:
 "I have been slowly sorting out siginfo and this is the culmination of
  that work.

  The primary result is in several ways the signal infrastructure has
  been made less error prone. The code has been updated so that manually
  specifying SEND_SIG_FORCED is never necessary. The conversion to the
  new siginfo sending functions is now complete, which makes it
  difficult to send a signal without filling in the proper siginfo
  fields.

  At the tail end of the patchset comes the optimization of decreasing
  the size of struct siginfo in the kernel from 128 bytes to about 48
  bytes on 64bit. The fundamental observation that enables this is by
  definition none of the known ways to use struct siginfo uses the extra
  bytes.

  This comes at the cost of a small user space observable difference.
  For the rare case of siginfo being injected into the kernel only what
  can be copied into kernel_siginfo is delivered to the destination, the
  rest of the bytes are set to 0. For cases where the signal and the
  si_code are known this is safe, because we know those bytes are not
  used. For cases where the signal and si_code combination is unknown
  the bits that won't fit into struct kernel_siginfo are tested to
  verify they are zero, and the send fails if they are not.

  I made an extensive search through userspace code and I could not find
  anything that would break because of the above change. If it turns out
  I did break something it will take just the revert of a single change
  to restore kernel_siginfo to the same size as userspace siginfo.

  Testing did reveal dependencies on preferring the signo passed to
  sigqueueinfo over si->signo, so bit the bullet and added the
  complexity necessary to handle that case.

  Testing also revealed bad things can happen if a negative signal
  number is passed into the system calls. Something no sane application
  will do but something a malicious program or a fuzzer might do. So I
  have fixed the code that performs the bounds checks to ensure negative
  signal numbers are handled"

* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
  signal: Guard against negative signal numbers in copy_siginfo_from_user32
  signal: Guard against negative signal numbers in copy_siginfo_from_user
  signal: In sigqueueinfo prefer sig not si_signo
  signal: Use a smaller struct siginfo in the kernel
  signal: Distinguish between kernel_siginfo and siginfo
  signal: Introduce copy_siginfo_from_user and use it's return value
  signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
  signal: Fail sigqueueinfo if si_signo != sig
  signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
  signal/unicore32: Use force_sig_fault where appropriate
  signal/unicore32: Generate siginfo in ucs32_notify_die
  signal/unicore32: Use send_sig_fault where appropriate
  signal/arc: Use force_sig_fault where appropriate
  signal/arc: Push siginfo generation into unhandled_exception
  signal/ia64: Use force_sig_fault where appropriate
  signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
  signal/ia64: Use the generic force_sigsegv in setup_frame
  signal/arm/kvm: Use send_sig_mceerr
  signal/arm: Use send_sig_fault where appropriate
  signal/arm: Use force_sig_fault where appropriate
  ...

Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs.  However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer.  (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)

This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/usb/core/driver.c: In function 'usb_driver_claim_interface':
drivers/usb/core/driver.c:513:21: warning:
 variable 'udev' set but not used [-Wunused-but-set-variable]

Since commit c183813fcee44a24 ("USB: remove LPM management from
usb_driver_claim_interface()"), 'udev' is not used.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the allocation of port_dev_path from the call to
kobject_get_path is not being kfree'd, causing a memory leak. Fix
this by kfree'ing this at the end of the function. Add an extra
error exit path to fix one of the early leaks when envp[0] fails
to be allocated.

Detected by CoverityScan, CID#1473771 ("Resource Leak")

Fixes: 201af55da8a3 ("usb: core: added uevent for over-current")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linus recently observed that if we did not worry about the padding
member in struct siginfo it is only about 48 bytes, and 48 bytes is
much nicer than 128 bytes for allocating on the stack and copying
around in the kernel.

The obvious thing of only adding the padding when userspace is
including siginfo.h won't work as there are sigframe definitions in
the kernel that embed struct siginfo.

So split siginfo in two; kernel_siginfo and siginfo.  Keeping the
traditional name for the userspace definition.  While the version that
is used internally to the kernel and ultimately will not be padded to
128 bytes is called kernel_siginfo.

The definition of struct kernel_siginfo I have put in include/signal_types.h

A set of buildtime checks has been added to verify the two structures have
the same field offsets.

To make it easy to verify the change kernel_siginfo retains the same
size as siginfo.  The reduction in size comes in a following change.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>