Since renesas_usb3 udc driver calls usb_of_get_companion_dev()
which is on usb/core/of.c, build error like below happens if we
disable CONFIG_USB because the usb/core/ needs CONFIG_USB:

ERROR: "usb_of_get_companion_dev" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!

According to the usb/gadget/Kconfig, "NOTE:  Gadget support
** DOES NOT ** depend on host-side CONFIG_USB !!".
So, to fix the issue, this patch changes the usb_of_get_companion_dev()
place from usb/core/of.c to usb/common/common.c to be called by both
host and gadget.

Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39facfa01c9f ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.

xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.

All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.

To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()

Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints

Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.

Remove the extra call to usb_cd_died with the shared hcd as parameter.

Fixes: ff9d78b36f76 ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This device does not correctly handle the LPM operations.

Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.

This patch adds the equivalent quirk logic as found in uas.

Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.

This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/

I just add device 201 for KS49 in quirks.c to get it works.

Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull USB/PHY updates from Greg KH:
 "Here is the big USB and phy driver patch set for 4.19-rc1.

  Nothing huge but there was a lot of work that happened this
  development cycle:

   - lots of type-c work, with drivers graduating out of staging, and
     displayport support being added.

   - new PHY drivers

   - the normal collection of gadget driver updates and fixes

   - code churn to work on the urb handling path, using irqsave()
     everywhere in anticipation of making this codepath a lot simpler in
     the future.

   - usbserial driver fixes and reworks

   - other misc changes

  All of these have been in linux-next with no reported issues for a
  while"

* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
  USB: serial: pl2303: add a new device id for ATEN
  usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
  usb: dwc3: gadget: Check MaxPacketSize from descriptor
  usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
  usb: dwc2: Turn on uframe_sched on "amlogic" platforms
  usb: dwc2: Turn on uframe_sched on "his" platforms
  usb: dwc2: Turn on uframe_sched on "bcm" platforms
  usb: dwc2: gadget: ISOC's starting flow improvement
  usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
  usb: dwc3: core: Enable AutoRetry feature in the controller
  usb: dwc3: Set default mode for dwc_usb31
  usb: gadget: udc: renesas_usb3: Add register of usb role switch
  usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
  usb: dwc2: Modify dwc2_readl/writel functions prototype
  usb: dwc3: pci: Intel Merrifield can be host
  usb: dwc3: pci: Supply device properties via driver data
  arm64: dts: dwc3: description of incr burst type
  usb: dwc3: Enable undefined length INCR burst type
  usb: dwc3: add global soc bus configuration reg0
  usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
  ...

Pull LED updates from Jacek Anaszewski:
 "LED triggers improvements make the biggest part of this pull request.
  The most striking ones, that allowed for nice cleanups in the triggers
  are:

   - centralized handling of creation and removal of trigger sysfs
     attributes via attribute group

   - addition of module_led_trigger() helper

  The other things that need to be mentioned:

  New features and improvements to existing LED class drivers:

   - lt3593: add DT support, switch to gpiod interface

   - lm3692x: support LED sync configuration, change OF calls to fwnode
     calls

   - apu: modify PC Engines apu/apu2 driver to support apu3

  Change in the drivers/net/can/led.c:

   - mark led trigger as broken since it's in the way for the further
     cleanups. It implements a subset of the netdev trigger and an Ack
     is needed from someone who can actually test and confirm that the
     netdev trigger works for can devices"

* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
  leds: ns2: Change unsigned to unsigned int
  usb: simplify usbport trigger
  leds: gpio trigger: simplifications from core changes
  leds: backlight trigger: simplifications from core changes
  leds: activity trigger: simplifications from core changes
  leds: default-on trigger: make use of module_led_trigger()
  leds: heartbeat trigger: simplifications from core changes
  leds: oneshot trigger: simplifications from core changes
  leds: transient trigger: simplifications from core changes
  leds: timer trigger: simplifications from core changes
  leds: netdev trigger: simplifications from core changes
  leds: triggers: new function led_set_trigger_data()
  leds: triggers: define module_led_trigger helper
  leds: triggers: handle .trigger_data and .activated() in the core
  leds: triggers: add device attribute support
  leds: triggers: let struct led_trigger::activate() return an error code
  leds: triggers: make the MODULE_LICENSE string match the actual license
  leds: lm3692x: Support LED sync configuration
  dt: bindings: lm3692x: Update binding for LED sync control
  leds: lm3692x: Change DT calls to fwnode calls
  ...

We want the USB fixes in here as well to handle merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on USB2.0 Spec Section 11.12.5,

  "If a hub has per-port power switching and per-port current limiting,
  an over-current on one port may still cause the power on another port
  to fall below specific minimums. In this case, the affected port is
  placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
  port, but PORT_OVER_CURRENT is not set."

so let's check C_PORT_OVER_CURRENT too for over current condition.

Fixes: 08d1dec6f405 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>