linux.git/drivers/usb/core/usb.h, branch v3.17

usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y

2014-05-27T23:51:51+00:00

Per Alan:
"You mean from within hub_handle_remote_wakeup()?  That routine will
never get called if CONFIG_PM_RUNTIME isn't enabled, because khubd
never sees wakeup requests if they arise during system suspend.

In fact, that routine ought to go inside the "#ifdef CONFIG_PM_RUNTIME"
portion of hub.c, along with the other suspend/resume code."

Suggested-by: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

usb: find internal hub tier mismatch via acpi

2014-05-27T23:38:52+00:00

ACPI identifies peer ports by setting their 'group_token' and
'group_position' _PLD data to the same value.  If a platform has tier
mismatch [1] , ACPI can override the default (USB3 defined) peer port
association for internal hubs.  External hubs follow the default peer
association scheme.

Location data is cached as an opaque cookie in usb_port_location data.

Note that we only consider the group_token and group_position attributes
from the _PLD data as ACPI specifies that group_token is a unique
identifier.

When we find port location data for a port then we assume that the
firmware will also describe its peer port.  This allows the
implementation to only ever set the peer once.  This leads to a question
about what happens when a pm runtime event occurs while the peer
associations are still resolving.  Since we only ever set the peer
information once, a USB3 port needs to be prevented from suspending
while its ->peer pointer is NULL (implemented in a subsequent patch).

There is always the possibility that firmware mis-identifies the ports,
but there is not much the kernel can do in that case.

[1]: xhci 1.1 appendix D figure 131
[2]: acpi 5 section 6.1.8

[alan]: don't do default peering when acpi data present
Suggested-by: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

usb: assign default peer ports for root hubs

2014-05-27T23:38:52+00:00

Assume that the peer of a superspeed port is the port with the same id
on the shared_hcd root hub.  This identification scheme is required of
external hubs by the USB3 spec [1].  However, for root hubs, tier mismatch
may be in effect [2].  Tier mismatch can only be enumerated via platform
firmware.  For now, simply perform the nominal association.

A new lock 'usb_port_peer_mutex' is introduced to synchronize port
device add/remove with peer lookups.  It protects peering against
changes to hcd->shared_hcd, hcd->self.root_hub, hdev->maxchild, and
port_dev->child pointers.

[1]: usb 3.1 section 10.3.3
[2]: xhci 1.1 appendix D

Cc: Alan Stern 
[alan: usb_port_peer_mutex locking scheme]
Acked-by: Alan Stern 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

usb: rename usb_port device objects

2014-05-27T23:35:10+00:00

The current port name "portX" is ambiguous.  Before adding more port
messages rename ports to "-portX"

This is an ABI change, but the suspicion is that it will go unnoticed as
the port power control implementation has been broken since its
introduction.  If however, someone was relying on the old name we can
add sysfs links from the old name to the new name.

Additionally, it unifies/simplifies port dev_printk messages and modifies
instances of:
	dev_XXX(hub->intfdev, ..."port %d"...
	dev_XXX(&hdev->dev, ..."port%d"...
into:
	dev_XXX(&port_dev->dev, ...

Now that the names are unique usb_port devices it would be nice if they
could be included in /sys/bus/usb.  However, it turns out that this
breaks 'lsusb -t'.  For now, create a dummy port driver so that print
messages are prefixed "usb 1-1-port3" rather than the
subsystem-ambiguous " 1-1-port3".

Finally, it corrects an odd usage of sscanf("port%d") in usb-acpi.c.

Suggested-by: Alan Stern 
Acked-by: Alan Stern 
Signed-off-by: Dan Williams 
Signed-off-by: Greg Kroah-Hartman

Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2014-04-02T00:06:09+00:00

Pull USB patches from Greg KH:
 "Here's the big USB pull request for 3.15-rc1.

  The normal set of patches, lots of controller driver updates, and a
  smattering of individual USB driver updates as well.

  All have been in linux-next for a while"

* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
  xhci: Transition maintainership to Mathias Nyman.
  USB: disable reset-resume when USB_QUIRK_RESET is set
  USB: unbind all interfaces before rebinding any
  usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
  usb: gadget: tcm_usb_gadget: stop format strings
  usb: gadget: f_fs: add missing spinlock and mutex unlock
  usb: gadget: composite: switch over to ERR_CAST()
  usb: gadget: inode: switch over to memdup_user()
  usb: gadget: f_subset: switch over to PTR_RET
  usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
  USB: keyspan: remove dead debugging code
  USB: serial: add missing newlines to dev_ messages.
  USB: serial: add missing braces
  USB: serial: continue to write on errors
  USB: serial: continue to read on errors
  USB: serial: make bulk_out_size a lower limit
  USB: cypress_m8: fix potential scheduling while atomic
  devicetree: bindings: document lsi,zevio-usb
  usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
  usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
  ...

USB: unbind all interfaces before rebinding any

2014-03-17T23:08:27+00:00

When a driver doesn't have pre_reset, post_reset, or reset_resume
methods, the USB core unbinds that driver when its device undergoes a
reset or a reset-resume, and then rebinds it afterward.

The existing straightforward implementation can lead to problems,
because each interface gets unbound and rebound before the next
interface is handled.  If a driver claims additional interfaces, the
claim may fail because the old binding instance may still own the
additional interface when the new instance tries to claim it.

This patch fixes the problem by first unbinding all the interfaces
that are marked (i.e., their needs_binding flag is set) and then
rebinding all of them.

The patch also makes the helper functions in driver.c a little more
uniform and adjusts some out-of-date comments.

Signed-off-by: Alan Stern 
Reported-and-tested-by: "Poulain, Loic" 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

usbcore: rename struct dev_state to struct usb_dev_state

2014-03-10T16:54:56+00:00

Since it is needed outside usbcore and exposed in include/linux/usb.h,
it conflicts with enum dev_state in rt2x00 wireless driver.

Mark it as usb specific to avoid conflicts in the future.

Signed-off-by: Valentina Manea 
Signed-off-by: Greg Kroah-Hartman

staging: usbip: claim ports used by shared devices

2014-03-09T06:48:43+00:00

A device should not be able to be used concurrently both by
the server and the client. Claiming the port used by the
shared device ensures no interface drivers bind to it and
that it is not usable from the server.

Signed-off-by: Valentina Manea 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

Revert "usbcore: set lpm_capable field for LPM capable root hubs"

2014-01-22T21:59:35+00:00

Commit 9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.

Unfortunately, that's not the case.  The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).

When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:

Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2

lspci for the affected host:

04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
        Subsystem: 1043:1039
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
Reported-by: Sergey Galanov 
Cc: stable@vger.kernel.org

usbcore: set lpm_capable field for LPM capable root hubs

2013-09-17T16:49:24+00:00

This patch sets the lpm_capable field for root hubs with LPM capabilities.

Signed-off-by: Xenia Ragiadakou 
Reported-by: Martin MOKREJS 
Suggested-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman