linux.git/drivers/usb/core/usb.h, branch v3.14

Revert "usbcore: set lpm_capable field for LPM capable root hubs"

2014-01-22T21:59:35+00:00

Commit 9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.

Unfortunately, that's not the case.  The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).

When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:

Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2

lspci for the affected host:

04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
        Subsystem: 1043:1039
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 
Reported-by: Sergey Galanov 
Cc: stable@vger.kernel.org

usbcore: set lpm_capable field for LPM capable root hubs

2013-09-17T16:49:24+00:00

This patch sets the lpm_capable field for root hubs with LPM capabilities.

Signed-off-by: Xenia Ragiadakou 
Reported-by: Martin MOKREJS 
Suggested-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: remove CONFIG_USB_SUSPEND option

2013-03-28T18:10:22+00:00

This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM).  The net result is code
shrinkage and simplification.

There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it.  The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.

Signed-off-by: Alan Stern 
CC: Peter Chen 
Signed-off-by: Greg Kroah-Hartman

Revert "usb: Register usb port's acpi power resources"

2013-01-29T15:33:07+00:00

This reverts commit 88bb965ed711e8a5984e70208ebc901a6ff4141f.

The linux-next branch of linux-pm tree has replaced
acpi_power_resource_(un)register_device() with new routines.
Commit 88bb965 will cause conflict in the linux-next tree.
So revert it and this will not affect other functions. Will
send a new patch with new routines after 3.9 merge window.

Signed-off-by: Lan Tianyu 
Signed-off-by: Greg Kroah-Hartman

usb: Register usb port's acpi power resources

2013-01-25T18:07:59+00:00

This patch is to register usb port's acpi power resources. Create
link between usb port device and its acpi power resource.

Acked-by: Alan Stern 
Signed-off-by: Lan Tianyu 
Signed-off-by: Greg Kroah-Hartman

USB: Set usb port's DeviceRemovable according acpi information

2013-01-21T21:22:03+00:00

ACPI provide "_PLD" and "_UPC" aml methods to describe usb port
visibility and connectability. This patch is to add usb_hub_adjust_DeviceRemovable()
to adjust usb hub port's DeviceRemovable according ACPI information and invoke it in
the rh_call_control(). When hub descriptor request is issued at first time,
usb port device isn't created and usb port is not bound with acpi. So first
hub descriptor request is not changed based on ACPI information. After usb
port devices being created, call usb_hub_adjust_DeviceRemovable in the hub_configure()
and then set hub port's DeviceRemovable according ACPI information and this also works
for non-root hub.

Acked-by: Alan Stern 
Signed-off-by: Lan Tianyu 
Signed-off-by: Greg Kroah-Hartman

usb/core: consider link speed while looking at bMaxPower

2013-01-12T00:16:01+00:00

The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch adds a helper function usb_get_max_power() which computes the
value based on config & usb_device's speed value. The the device descriptor
dump computes the value on its own.

Cc: Sarah Sharp 
Cc: Greg Kroah-Hartman 
Acked-by: Alan Stern 
Signed-off-by: Sebastian Andrzej Siewior 
Signed-off-by: Greg Kroah-Hartman

usb/acpi: Store info on device removability.

2012-09-10T20:04:01+00:00

In the upcoming USB port power off patches, we need to know whether a
USB port can ever see a disconnect event.  Often USB ports are internal
to a system, and users can't disconnect USB devices from that port.
Sometimes those ports will remain empty, because the OEM chose not to
connect an internal USB device to that port.

According to ACPI Spec 9.13, PLD indicates whether USB port is
user visible and _UPC indicates whether a USB device can be connected to
the USB port (we'll call this "connectible").  Here's a matrix of the
possible combinations:

Visible Connectible
		Name		Example
-------------------------------------------------------------------------

Yes	No	Unknown		(Invalid state.)

Yes	Yes	Hot-plug	USB ports on the outside of a laptop.
				A user could freely connect and disconnect
				USB devices.

No	Yes	Hard-wired	A USB modem hard-wired to a port on the
				inside of a laptop.

No	No	Not used	The port is internal to the system and
				will remain empty.

Represent each of these four states with an enum usb_port_connect_type.
The four states are USB_PORT_CONNECT_TYPE_UNKNOWN,
USB_PORT_CONNECT_TYPE_HOT_PLUG, USB_PORT_CONNECT_TYPE_HARD_WIRED, and
USB_PORT_NOT_USED.  When we get the USB port's acpi_handle, store the
state in connect_type in struct usb_port.

Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

usb/acpi: Bind ACPI node to USB port, not usb_device.

2012-09-10T20:02:02+00:00

In the ACPI DSDT table, only usb root hub and usb ports are ACPI device
nodes.  Originally, we bound the usb port's ACPI node to the usb device
attached to the port.  However, we want to access those ACPI port
methods when the port is empty, and there's no usb_device associated
with that port.

Now that the usb port is a real device, we can bind the port's ACPI node
to struct usb_port instead.

Signed-off-by: Lan Tianyu 
Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

usb: Add quirk detection based on interface information

2012-07-19T22:44:58+00:00

When a whole class of devices (possibly from a specific vendor, or
across multiple vendors) require a quirk, explictly listing all devices
in the class make the quirks table unnecessarily large. Fix this by
allowing matching devices based on interface information.

Signed-off-by: Laurent Pinchart 
Acked-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman