Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix the following sparse warning:

drivers/usb/core/message.c:1583:6: warning: symbol '__usb_queue_reset_device' was not declared. Should it be static?

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Make the USB core check the bandwidth when switching from one
interface alternate setting to another.  Also check the bandwidth
when resetting a configuration (so that alt setting 0 is used).  If
this check fails, the device's state is unchanged.  If the device
refuses the new alt setting, re-instate the old alt setting in the
host controller hardware.

If a USB device doesn't have an alternate interface setting 0, install
the first alt setting in its descriptors when a new configuration is
requested, or the device is reset.

Add a mutex per root hub to protect bandwidth operations:
adding/reseting/changing configurations, and changing alternate interface
settings.  We want to ensure that the xHCI host controller and the USB
device are set up for the same configurations and alternate settings.
There are two (possibly three) steps to do this:

 1. The host controller needs to check that bandwidth is available for a
    different setting, by issuing and waiting for a configure endpoint
    command.
 2. Once that returns successfully, a control message is sent to the
    device.
 3. If that fails, the host controller must be notified through another
    configure endpoint command.

The mutex is used to make these three operations seem atomic, to prevent
another driver from using more bandwidth for a different device while
we're in the middle of these operations.

While we're touching the bandwidth code, rename usb_hcd_check_bandwidth()
to usb_hcd_alloc_bandwidth().  This function does more than just check
that the bandwidth change won't exceed the bus bandwidth; it actually
changes the bandwidth configuration in the xHCI host controller.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1298) fixes a bug in the new scatter-gather URB
facility.  If an URB uses a scatterlist then it should not have the
URB_NO_INTERRUPT flag set; otherwise the system won't be notified when
the transfer completes.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The WHCI HCD will also support urbs with scatter-gather lists.  Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD.  Use this to decide whether to pass the scatter-list to the HCD
or not.

Make the usb-storage driver use this new field.

Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

This fix permits the "new" usbmon to access usb-storage's data buffer
without DMA remapping tricks. It should be compatible with PIO controllers
and not add any new crashes. Note that from now on PIO controllers and
usbmon are uniform in their access pattern and if one crashes then
the other will too. Hopefuly neither does.

As a side effect, we get rid for #ifdefs, which were a little ugly.

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

commit b7af0bb ("USB: allow malformed LANGID descriptors") broke support
for devices without string descriptor support.

Reporting string descriptors is optional to USB devices, and a device
lets us know it can't deal with strings by responding to the LANGID
request with a STALL token.

The kernel handled that correctly before b7af0bb came in, but failed
hard if the LANGID was reported but broken. More than that, if a device
was not able to provide string descriptors, the LANGID was retrieved
over and over again at each string read request.

This patch changes the behaviour so that

 a) the LANGID is only queried once
 b) devices which can't handle string requests are not asked again
 c) devices with malformed LANGID values have a sane fallback to 0x0409

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is the original patch I created before David Vrabel posted a better
patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does
basically the same thing.  This patch will get replaced with his
(modified) patch later.

Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push
bulk endpoint scatter gather lists down to the host controller drivers.
This allows host controller drivers to more efficiently enqueue these
transfers, and allows the xHCI host controller to better take advantage of
USB 3.0 "bursts" for bulk endpoints.

This patch currently only enables scatter gather lists for bulk endpoints.
Other endpoint types that use the usb_sg_* functions will not have their
scatter gather lists pushed down to the host controller.  For periodic
endpoints, we want each scatterlist entry to be a separate transfer.
Eventually, HCDs could parse these scatter-gather lists for periodic
endpoints also.  For now, we use the old code and call usb_submit_urb()
for each scatterlist entry.

The caller of usb_sg_init() can request that all bytes in the scatter
gather list be transferred by passing in a length of zero.  Handle that
request for a bulk endpoint under xHCI by walking the scatter gather list
and calculating the length.  We could let the HCD handle a zero length in
this case, but I'm not sure if the core layers in between will get
confused by this.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Originally, the USB core had no support for allocating bandwidth when a
particular configuration or alternate setting for an interface was
selected.  Instead, the device driver's URB submission would fail if
there was not enough bandwidth for a periodic endpoint.  Drivers could
work around this, by using the scatter-gather list API to guarantee
bandwidth.

This patch adds host controller API to allow the USB core to allocate or
deallocate bandwidth for an endpoint.  Endpoints are added to or dropped
from a copy of the current schedule by calling add_endpoint() or
drop_endpoint(), and then the schedule is atomically evaluated with a
call to check_bandwidth().  This allows all the endpoints for a new
configuration or alternate setting to be added at the same time that the
endpoints from the old configuration or alt setting are dropped.

Endpoints must be added to the schedule before any URBs are submitted to
them.  The HCD must be allowed to reject a new configuration or alt
setting before the control transfer is sent to the device requesting the
change.  It may reject the change because there is not enough bandwidth,
not enough internal resources (such as memory on an embedded host
controller), or perhaps even for security reasons in a virtualized
environment.

If the call to check_bandwidth() fails, the USB core must call
reset_bandwidth().  This causes the schedule to be reverted back to the
state it was in just after the last successful check_bandwidth() call.

If the call succeeds, the host controller driver (and hardware) will have
changed its internal state to match the new configuration or alternate
setting.  The USB core can then issue a control transfer to the device to
change the configuration or alt setting.  This allows the core to test new
configurations or alternate settings before unbinding drivers bound to
interfaces in the old configuration.

WIP:

The USB core must add endpoints from all interfaces in a configuration
to the schedule, because a driver may claim that interface at any time.
A slight optimization might be to add the endpoints to the schedule once
a driver claims that interface.  FIXME

This patch does not cover changing alternate settings, but it does
handle a configuration change or de-configuration.  FIXME

The code for managing the schedule is currently HCD specific.  A generic
scheduling algorithm could be added for host controllers without
built-in scheduling support.  For now, if a host controller does not
define the check_bandwidth() function, the call to
usb_hcd_check_bandwidth() will always succeed.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>