linux.git/drivers/usb/core/hcd.c, branch v2.6.34

USB: fix the idProduct value for USB-3.0 root hubs

2010-03-02T22:55:07+00:00

This patch (as1346) changes the idProduct value for USB-3.0 root hubs
from 0x0002 (which we already use for USB-2.0 root hubs) to 0x0003.

Signed-off-by: Alan Stern 
Acked-by: Sarah Sharp 
CC: stable 
Signed-off-by: Greg Kroah-Hartman

USB: convert to the runtime PM framework

2010-03-02T22:54:12+00:00

This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework.  This involves numerous changes throughout
usbcore, especially to hub.c and driver.c.  Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.

Several fields in the usb_device and usb_interface structures are no
longer needed.  Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).

The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else.  They won't remain
suspended.  But if they aren't in use then they will naturally
autosuspend again in a few seconds.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: consolidate remote wakeup routines

2010-03-02T22:54:08+00:00

This patch (as1324) makes a small change to the code used for remote
wakeup of root hubs.  hcd_resume_work() now calls the hub driver's
remote-wakeup routine instead of implementing its own version.

The patch is complicated by the need to rename remote_wakeup() to
usb_remote_wakeup(), make it non-static, and declare it in a header
file.  There's also the additional complication required to make
everything work when CONFIG_PM isn't set; the do-nothing inline
routine had to be moved into the header file.

Signed-off-by: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB: Use bInterfaceNumber in bandwidth allocations.

2010-03-02T22:54:04+00:00

USB devices do not have to sort interfaces in their descriptors based on
the interface number, and they may choose to skip interface numbers.  The
USB bandwidth allocation code for installing a new configuration assumes
the for loop variable will match the interface number.  Make it use the
interface number (bInterfaceNumber) in the descriptor instead.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: Fix duplicate sysfs problem after device reset.

2010-01-20T23:24:35+00:00

Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate.  It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:

[  427.681810] Restarting tasks ...
[  427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[  427.682019] usb usb3: usb resume
[  427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[  427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[  427.682205] usb 1-2: usb wakeup-resume
[  427.682226] usb 1-2: finish reset-resume
[  427.682886] done.
[  427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.746682] hub 3-0:1.0: hub_reset_resume
[  427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[  427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[  427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[  427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[  427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[  427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[  427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[  427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[  427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[  427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[  427.916609]  ep_81: create, parent hub
[  427.916632] ------------[ cut here ]------------
[  427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[  427.916649] Hardware name: System Product Name
[  427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[  427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[  427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[  427.916699] Call Trace:

The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.

After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces.  However, the
USB core keeps track of the old state, which may include non-zero
alternate settings.  It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.

The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0.  This caused duplicate
endpoint files to be created.

The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device().  Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.

Signed-off-by: Sarah Sharp 
Tested-by: Borislav Petkov 
Cc: Alan Stern 
Signed-off-by: Greg Kroah-Hartman

USB core: fix recent kernel-doc warnings

2009-12-23T19:34:12+00:00

Fix new kernel-doc warnings in usb core:

Warning(drivers/usb/core/usb.c:79): No description found for parameter 'config'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'iface_num'
Warning(drivers/usb/core/usb.c:79): No description found for parameter 'alt_num'
Warning(drivers/usb/core/hcd.c:1622): No description found for parameter 'udev'

Signed-off-by: Randy Dunlap 
Signed-off-by: Greg Kroah-Hartman

USB: Check bandwidth when switching alt settings.

2009-12-11T19:55:27+00:00

Make the USB core check the bandwidth when switching from one
interface alternate setting to another.  Also check the bandwidth
when resetting a configuration (so that alt setting 0 is used).  If
this check fails, the device's state is unchanged.  If the device
refuses the new alt setting, re-instate the old alt setting in the
host controller hardware.

If a USB device doesn't have an alternate interface setting 0, install
the first alt setting in its descriptors when a new configuration is
requested, or the device is reset.

Add a mutex per root hub to protect bandwidth operations:
adding/reseting/changing configurations, and changing alternate interface
settings.  We want to ensure that the xHCI host controller and the USB
device are set up for the same configurations and alternate settings.
There are two (possibly three) steps to do this:

 1. The host controller needs to check that bandwidth is available for a
    different setting, by issuing and waiting for a configure endpoint
    command.
 2. Once that returns successfully, a control message is sent to the
    device.
 3. If that fails, the host controller must be notified through another
    configure endpoint command.

The mutex is used to make these three operations seem atomic, to prevent
another driver from using more bandwidth for a different device while
we're in the middle of these operations.

While we're touching the bandwidth code, rename usb_hcd_check_bandwidth()
to usb_hcd_alloc_bandwidth().  This function does more than just check
that the bandwidth change won't exceed the bus bandwidth; it actually
changes the bandwidth configuration in the xHCI host controller.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: Refactor code to find alternate interface settings.

2009-12-11T19:55:27+00:00

Refactor out the code to find alternate interface settings into
usb_find_alt_setting().  Print a debugging message and return null if the
alt setting is not found.

While we're at it, correct a bug in the refactored code.  The interfaces
in the configuration's interface cache are not necessarily in numerical
order, so we can't just use the interface number as an array index.  Loop
through the interface caches, looking for the correct interface.

Signed-off-by: Sarah Sharp 
Signed-off-by: Greg Kroah-Hartman

USB: hcd.c: quiet NULL pointer sparse noise

2009-12-11T19:55:21+00:00

Quiet the following sparse noise:

  warning: Using plain integer as NULL pointer

Signed-off-by: H Hartley Sweeten 
Cc: Alan Stern 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

USB: Check results of dma_map_single

2009-12-11T19:55:20+00:00

In map_urb_for_dma(), the DMA address returned by dma_map_single()
is not checked to determine if it is legal. This lack of checking
contributed to a problem with the libertas wireless driver
(http://marc.info/?l=linux-wireless&m=125695331205062&w=2). The
difficulty was not detected until the buffer was unmapped. By this time
memory corruption had occurred.

The situation is fixed by testing the returned DMA address, and
returning -EAGAIN if the address is invalid.

Signed-off-by: Larry Finger 
Cc: Alan Stern 
Signed-off-by: Greg Kroah-Hartman