linux.git/drivers/usb/core/config.c, branch v4.13

usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk

2017-03-14T09:07:31+00:00

Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.

The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms.  It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies.  The generic config code does not
catch this case because the 64ms is considered a sane enough value.

This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.

Signed-off-by: Samuel Thibault 
Acked-by: Alan Stern 
Cc: stable 
Signed-off-by: Greg Kroah-Hartman

USB: fix problems with duplicate endpoint addresses

2017-01-05T18:38:40+00:00

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [] panic+0x1cb/0x3a9 kernel/panic.c:179
 [] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [] kobject_add+0x139/0x220 lib/kobject.c:411
 [] device_add+0x353/0x1660 drivers/base/core.c:1088
 [] device_register+0x1d/0x20 drivers/base/core.c:1206
 [] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.

Signed-off-by: Alan Stern 
Reported-by: Andrey Konovalov 
Tested-by: Andrey Konovalov 
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: core: add missing license information to some files

2016-10-29T16:51:56+00:00

Some of the USB core files were missing explicit license information.
As all files in the kernel tree are implicitly licensed under the
GPLv2-only, be explicit in case someone get confused looking at
individual files by using the SPDX nomenclature.

Signed-off-by: Greg Kroah-Hartman

USB: change bInterval default to 10 ms

2016-09-16T14:29:41+00:00

Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before.  However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.

Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid.  It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below.  To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.

Signed-off-by: Alan Stern 
Tested-by: Wade Berrier 
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: fix typo in wMaxPacketSize validation

2016-08-23T10:54:32+00:00

The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.

Signed-off-by: Alan Stern 
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: 
Signed-off-by: Greg Kroah-Hartman

USB: validate wMaxPacketValue entries in endpoint descriptors

2016-08-09T14:14:18+00:00

Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values.  This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.

This issue was first discovered and tests were conducted by Jake Lamberson
, an intern working for Rosie Hall.

Signed-off-by: Alan Stern 
Reported-by: roswest 
Tested-by: roswest 
CC: 
Signed-off-by: Greg Kroah-Hartman

usb: fix regression in SuperSpeed endpoint descriptor parsing

2016-03-31T04:57:58+00:00

commit b37d83a6a414 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.

The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.

This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:

"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
 ep 129: using minimum values"

Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.

Fixes: b37d83a6a414
Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: Add USB 3.1 Precision time measurement capability descriptor support

2016-02-15T01:03:23+00:00

USB 3.1 devices that support precision time measurement have an
additional PTM cabaility descriptor as part of the full BOS descriptor

Look for this descriptor while parsing the BOS descriptor, and store it in
struct usb_hub_bos if it exists.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: Parse the new USB 3.1 SuperSpeedPlus Isoc endpoint companion descriptor

2016-02-15T01:03:23+00:00

USB 3.1 devices can return a new SuperSpeedPlus isoc endpoint companion
descriptor for a isochronous endpoint that requires more than 48K bytes
per Service Interval.

The new descriptor immediately follows the old USB 3.0 SuperSpeed Endpoint
Companion and will provide a new BytesPerInterval value.

It is parsed and stored in struct usb_host_endpoint with the other endpoint
related descriptors, and should be used by USB3.1 capable hosts to reserve
bus time in the schedule.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman

usb: define USB_SPEED_SUPER_PLUS speed for SuperSpeedPlus USB3.1 devices

2016-01-25T04:16:52+00:00

Add a new USB_SPEED_SUPER_PLUS device speed, and make sure usb core can
handle the new speed.
In most cases the behaviour is the same as with USB_SPEED_SUPER SuperSpeed
devices. In a few places we add a "Plus" string to inform the user of the
new speed.

Signed-off-by: Mathias Nyman 
Signed-off-by: Greg Kroah-Hartman