linux.git/drivers/usb/chipidea/core.c, branch v3.14 Linux kernel source tree usb: chipidea: put hw_phymode_configure before ci_usb_phy_init 2014-01-13T23:55:19+00:00 Chris Ruehl chris.ruehl@gtsys.com.hk 2014-01-10T05:51:30+00:00 cd0b42c2a6d2a74244f0053f8960f5dad5842278 hw_phymode_configure configures the PORTSC registers and allow the following phy_inits to operate on the right parameters. This fix a problem where the UPLI (ISP1504) could not be detected, because the Viewport was not available and read the viewport return 0's only. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
hw_phymode_configure configures the PORTSC registers and allow the
following phy_inits to operate on the right parameters. This fix a problem
where the UPLI (ISP1504) could not be detected, because the Viewport was not
available and read the viewport return 0's only.

Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag 2014-01-13T23:55:19+00:00 Chris Ruehl chris.ruehl@gtsys.com.hk 2014-01-10T05:51:29+00:00 3b5d3e6845bfe68777d069886b0d1cd5f23b9d58 * init the sts flag to 0 (missed) * fix write the real bit not sts value * Set PORTCS_STS and DEVLC_STS only if sts = 1 [Peter Chen: This one and the next patch fix the problem occurred imx27 and imx31, and imx27 and imx31 usb support are enabled until 3.14, so these two patches isn't needed for -stable] Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
* init the sts flag to 0 (missed)
* fix write the real bit not sts value
* Set PORTCS_STS and DEVLC_STS only if sts = 1

[Peter Chen: This one and the next patch fix the problem occurred imx27
and imx31, and imx27 and imx31 usb support are enabled until 3.14, so
these two patches isn't needed for -stable]

Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: add freescale imx28 special write register method 2014-01-13T23:55:19+00:00 Peter Chen peter.chen@freescale.com 2014-01-10T05:51:27+00:00 ed8f8318d2ef3e5f9e4ddf79349508c116b68d7f According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB register error issue", All USB register write operations must use the ARM SWP instruction. So, we implement special hw_write and hw_test_and_clear for imx28. Discussion for it at below: http://marc.info/?l=linux-usb&m=137996395529294&w=2 This patch is needed for stable tree 3.11+. Cc: stable@vger.kernel.org Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.

Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2

This patch is needed for stable tree 3.11+.

Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: mark register map as "const" and convert to u8 2014-01-08T00:21:06+00:00 Marc Kleine-Budde mkl@pengutronix.de 2014-01-06T02:10:39+00:00 987e7bc3484fdc8c8018e1368608f6a81053b86f This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as "const". Further, as all offset fit into a single byte, the type is changed from uintptr_t to u8. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as
"const". Further, as all offset fit into a single byte, the type is changed
from uintptr_t to u8.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: move malloced regmap directly into struct hw_bank 2014-01-08T00:21:06+00:00 Marc Kleine-Budde mkl@pengutronix.de 2014-01-06T02:10:38+00:00 21395a1aac7ce1e19dbb43542a9e06cca2bfca01 Without this patch a seperate chunk of memory is allocated for the regmap array. As the regmap is always used it makes no sense to allocate a seperate memory block for it, this patch moves the regmap array directly into the struct hw_bank. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Without this patch a seperate chunk of memory is allocated for the regmap
array. As the regmap is always used it makes no sense to allocate a seperate
memory block for it, this patch moves the regmap array directly into the struct
hw_bank.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge 3.13-rc5 into usb-next 2013-12-24T18:18:03+00:00 Greg Kroah-Hartman gregkh@linuxfoundation.org 2013-12-24T18:18:03+00:00 99f14bd4d1b2a1b1b6cd508e08efdbc5e3919198 This resolves the merge issue with drivers/usb/host/ohci-at91.c Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
This resolves the merge issue with drivers/usb/host/ohci-at91.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: fix nobody cared IRQ when booting with host role 2013-12-09T21:14:12+00:00 Peter Chen peter.chen@freescale.com 2013-12-05T07:20:50+00:00 5a1e1456fc633da5291285b1fff75d2a7507375b If we connect Male-A-To-Male-A cable between otg-host and host pc, the ci->vbus_active is set wrongly, and cause the controller run at peripheral mode when we load gadget module (ci_udc_start will be run), but the software runs at host mode due to id = 0. The ehci_irq can't handle suspend (USBi_SLI) interrupt which is enabled for peripheral mode, it causes no one will handle irq error. This patch is needed for 3.12 stable Cc: stable <stable@vger.kernel.org> Acked-by: Michael Grzeschik <mgr@pengutronix.de> Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.

This patch is needed for 3.12 stable

Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: Reallocate regmap only if lpm is detected 2013-12-09T02:02:54+00:00 Chris Ruehl chris.ruehl@gtsys.com.hk 2013-12-06T08:35:12+00:00 aeb2c1210d71c00a4b59d343b0a7df6b1059eb89 The regmap only needs to reallocate if the hw_read on the CAP register shows lpm is used. Therefore the if() statement check the change. Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
The regmap only needs to reallocate if the hw_read on the CAP register shows
lpm is used. Therefore the if() statement check the change.

Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: only get vbus regulator for non-peripheral mode 2013-10-30T16:41:49+00:00 Peter Chen peter.chen@freescale.com 2013-10-30T01:19:29+00:00 c2ec3a732a6bb65635693f6d86d2b7bf073b6148 If the user chooses peripheral mode for this controller, the vbus regulator doesn't need to get, since the host will supply the vbus, it can save one vbus pin for other usage. Signed-off-by: Peter Chen <peter.chen@freescale.com> Tested-by: Frank Li <frank.li@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
If the user chooses peripheral mode for this controller, the vbus
regulator doesn't need to get, since the host will supply the vbus,
it can save one vbus pin for other usage.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Frank Li <frank.li@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb: chipidea: add ci_hdrc_enter_lpm API 2013-10-01T01:54:07+00:00 Peter Chen peter.chen@freescale.com 2013-09-24T04:47:55+00:00 864cf949981754c53de0a2efdc6c542c51d61328 This API is used to let the PHY enter/leave low power mode. Before the controller going to work(at probe/resume), it needs to let the PHY leave low power mode. After the controller stopping working(at remove/suspend), it needs to let the PHY enter low power mode to save power consumption. Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
This API is used to let the PHY enter/leave low power mode.
Before the controller going to work(at probe/resume), it needs to let
the PHY leave low power mode.
After the controller stopping working(at remove/suspend), it needs to
let the PHY enter low power mode to save power consumption.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>