linux.git/drivers/usb/atm, branch v2.6.24

signedness: module_param_array nump argument

2007-10-14T19:41:52+00:00

... should be unsigned int

Signed-off-by: Al Viro 
Signed-off-by: Linus Torvalds

USB: cxacru: Use appropriate logging for errors

2007-10-12T21:55:28+00:00

When an error occurs, existing logging uses dbg() so the cause of a
problem is hard to determine. Error conditions shouldn't only be
properly reported with debugging enabled.

A side effect of this change is that when an uninitialised device is
started, a log message similar to the following is sent:
	cxacru 5-2:1.0: receive of cm 0x90 failed (-104)
This is normal - the device did not respond so firmware will be loaded.

Signed-off-by: Simon Arlott 
Acked-by: Duncan Sands 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Cosmetic

2007-10-12T21:55:18+00:00

Update copyrights and remove not necessary warning (ueagle-atm works
well on suspend/resume).

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Do not sleep when device is disconnected

2007-10-12T21:55:17+00:00

Do not sleep in kernel thread when device is disconnected, this make faster
suspending and module unloading. Use one wait queue for sleeping.

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Avoid keyboard driver blocking

2007-10-12T21:55:17+00:00

Ueagle-atm driver load DSP firmware in function, which is running from
common workqueue. In some (error) circumstances loading firmware may
sleep for long periods (even 60 seconds, depending on timeout). This
block keyboard driver, which also use common workqueue. To fix problem
use custom workqueue in ueagle-atm.

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Allow user to choose input interface alternate setting

2007-10-12T21:55:17+00:00

Let's user control how much USB bus bandwidth will be reserved by
ueagle-atm device. This make possible to share bus with other devices
when ueagle-atm driver works in isochronous mode.

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Devolo and Elsa chipsets support

2007-10-12T21:55:17+00:00

Support for Devolo and Elsa chipsets. These chipsets have no information
about ADSL annex (line type) encoded in USB descriptors. Driver try to
get this information from USB VID and PID or it can be explicitly set by
the user through module parameter. Thanks to Johann Hanne, whose make
most of this patch.

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Eagle IV chipset support

2007-10-12T21:55:17+00:00

Add support to newest chipset of eagle family. It is compatible with
older chipsets at USB level. However DSP firmware and CMVs
(Configuration and Management Variables) have different format of data
and are sent/received by different way.  

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman

USB: Remove unneeded pointer intf from speedtch_upload_firmware()

2007-10-12T21:54:58+00:00

This trivial patch removes the unneeded pointer intf returned from
usb_ifnum_to_if(), which is never used. The check for NULL can be simply done
by if (!usb_ifnum_to_if(usb_dev, 2)).

Signed-off-by: Micah Gruber 
Signed-off-by: Greg Kroah-Hartman

UEAGLE: Remove sysfs files on error case

2007-08-22T21:28:00+00:00

Bugfix, remove sysfs files when modem fails to boot.

Signed-off-by: Stanislaw Gruszka 
Signed-off-by: Greg Kroah-Hartman