linux.git/drivers/usb/atm, branch v2.6.17

[PATCH] USBATM: fix modinfo output

2006-05-09T06:43:54+00:00

Because of the way stringify works, using an expression
like 64 * 1024 for UDSL_MAX_BUF_SIZE results in 64 * 1024
turning up in the modinfo output instead of 65536.  So use
65536 directly (this was the only way I found of fixing this).

Signed-off-by: Duncan Sands 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USBATM: change the default speedtouch iso altsetting

2006-05-09T06:43:54+00:00

The maximum possible bandwidth for a speedtouch modem is about 7Mbaud.
You can only get this by using isochronous urbs (enable_isoc=1) and
altsetting 3.  With the current default altsetting of 2, the modem
maxes out at about 4Mbaud.  So change the default altsetting to 3
when using isochronous urbs.  It would be nice to base the altsetting
on the detected line speed, but that's hard given the current design.

Signed-off-by: Duncan Sands 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: UEAGLE : memory leack fix

2006-04-14T18:12:23+00:00

this patch fix leak of memory allocated to intr if allocation of
sc->urb_int fails.
Found by the Coverity checker.

Signed-off-by: Duncan Sands 
Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: UEAGLE : null pointer dereference fix

2006-04-14T18:12:23+00:00

this patch fix potential null pointer dereference.  Found by the
Coverity checker.

Signed-off-by: Duncan Sands 
Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: UEAGLE : support geode

2006-04-14T18:12:23+00:00

- increase ack timeout for slow system (geode 233MHz where HZ=100)
- reset the cmv ack flag when rebooting

Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USB: UEAGLE : cosmetic

2006-04-14T18:12:23+00:00

- improve debug trace in order to make easy to solve user problems.
- indent some code
- increase version number

Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] UEAGLE : cmv name bug (was cosmetic)

2006-02-01T01:23:41+00:00

this patch correct a possible bug with cmv_name being static. If there
is 2 modems and the driver is scheduled when filling cmv_name this could
result with garbage in cmv_name. We allocate cmv_name on the stack but
with a small size in order to avoid that.

Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] UEAGLE : cosmetic

2006-02-01T01:23:41+00:00

this patch is purely cosmetic. There is :
- indentation cleaning
- unneeded cast removing
- comments cleaning

Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] UEAGLE : add iso support

2006-02-01T01:23:40+00:00

This patch adds the support for isochronous pipe.

A new module parameter is added to select iso mode.  It is set to iso by
default because bulk mode doesn't work well at high speed rate (>3 Mbps
for upload).

We use UDSL_IGNORE_EILSEQ flags because ADI firmware doesn't reply to
ISO IN when it has nothing to send [1].

[1]
from cypress datasheet :

The ISOSEND0 Bit (bit 7 in the USBPAIR Register) is used when the EZ-USB
FX chip receives an isochronous IN token while the IN FIFO is empty. If
ISOSEND0=0 (the default value), the USB core does not respond to the IN
token. If ISOSEND0=1, the USB core sends a zero-length data packet in
response to the IN token. The action to take depends on the overall
system design. The ISOSEND0 Bit applies to all of the isochronous IN
endpoints, IN-8 through IN-15.

Signed-off-by: Matthieu CASTET 
Signed-off-by: Greg Kroah-Hartman

[PATCH] USBATM: semaphore to mutex conversion

2006-02-01T01:23:40+00:00

This is the usbatm part of the Arjan, Jes and Ingo
mass semaphore to mutex conversion, reworked to apply on top
of the patches I just sent to you.  This time, with correct
attribution and signed-off lines.

Signed-off-by: Arjan van de Ven 
Signed-off-by: Ingo Molnar 
Signed-off-by: Duncan Sands 
Signed-off-by: Greg Kroah-Hartman