Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.

The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add OHCI glue code for JZ4740 SoCs OHCI module.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1411/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
  USB: backlight, appledisplay: fix incomplete registration failure handling
  USB: pl2303: remove unnecessary reset of usb_device in urbs
  USB: ftdi_sio: remove obsolete check in unthrottle
  USB: ftdi_sio: remove unused tx_bytes counter
  USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
  USB: pl2303: initial TIOCGSERIAL support
  USB: option: add Longcheer/Longsung vendor ID
  USB: fix I2C API usage in ohci-pnx4008.
  USB: usbmon: mask seconds properly in text API
  USB: sisusbvga: no unnecessary GFP_ATOMIC
  USB: storage: onetouch: unnecessary GFP_ATOMIC
  USB: serial: ftdi: add CONTEC vendor and product id
  USB: remove references to port->port.count from the serial drivers
  USB: tty: Prune uses of tty_request_room in the USB layer
  USB: tty: Add a function to insert a string of characters with the same flag
  USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
  USB: tty: kill request_room for USB ACM class
  USB: tty: sort out the request_room handling for whiteheat
  USB: storage: fix misplaced parenthesis
  USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
  ...

Texas Instruments DA8xx/OMAP-L1x OHCI glue layer.

This OHCI implementation is not without quirks: there's only one physical port
despite the root hub reporting two; the port's power control and over-current
status bits are not connected to any pins, however, at least on the DA830 EVM
board, those signals are connected via GPIO, thus the provision was made for
overriding the OHCI port power and over-current bits at the board level...

Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Replace ARCH_OMAP34XX with ARCH_OMAP3

Signed-off-by: Tony Lindgren <tony@atomide.com>

usb: ehci: Allow EHCI to be built on OMAP3

OMAP3 chips have a built-in EHCI controller.
The recently introduced omap ehci-hcd driver missed
out on selecting USB_ARCH_HAS_EHCI in Kconfig.

Without this, the driver cannot be built.

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.

Users have to pass details about serial interface configuration in the
platform data.

The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
  microblaze: Disable heartbeat/enable emaclite in defconfigs
  microblaze: Support simpleImage.dts make target
  microblaze: Fix _start symbol to physical address
  microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
  microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
  microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
  microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
  microblaze: Support ptrace syscall tracing.
  microblaze: Updated CPU version and FPGA family codes in PVR
  microblaze: Generate correct signal and siginfo for integer div-by-zero
  microblaze: Don't be noisy when userspace causes hardware exceptions
  microblaze: Remove ipc.h file which points to non-existing asm-generic file
  microblaze: Clear sticky FSR register after generating exception signals
  microblaze: Ensure CPU usermode is set on new userspace processes
  microblaze: Use correct kbuild variable KBUILD_CFLAGS
  microblaze: Save and restore msr in hw exception
  microblaze: Add architectural support for USB EHCI host controllers
  microblaze: Implement include/asm/syscall.h.
  microblaze: Improve checking mechanism for MSR instruction
  microblaze: Add checking mechanism for MSR instruction
  ...