Pull tty/serial fixes from Greg KH:
 "Here are some small tty/serial driver fixes for 4.5-rc2.

  They resolve a number of reported problems (the ioctl one specifically
  has been pointed out by numerous people) and one patch adds some new
  device ids for the 8250_pci driver.  All have been in linux-next
  successfully"

* tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: 8250_pci: Add Intel Broadwell ports
  staging/speakup: Use tty_ldisc_ref() for paste kworker
  n_tty: Fix unsafe reference to "other" ldisc
  tty: Fix unsafe ldisc reference via ioctl(TIOCGETD)
  tty: Retry failed reopen if tty teardown in-progress
  tty: Wait interruptibly for tty lock on reopen

Pull staging fixes from Greg KH:
 "Here are some small staging driver fixes for 4.5-rc2.

  One of them predated 4.4-final, but I missed that merge window due to
  the holliday.  The others fix reported issues that have come up
  recently.  The tty change is needed for the speakup driver fix and has
  the ack of the tty driver maintainer as well, i.e.  myself :)

  All have been in linux-next with no reported issues"

* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  Staging: speakup: fix read scrolled-back VT
  Staging: speakup: Fix getting port information
  Revert "Staging: panel: usleep_range is preferred over udelay"
  iio: adis_buffer: Fix out-of-bounds memory access

Some recent (early 2015) macbooks have Intel Broadwell where LPSS UARTs are
PCI enumerated instead of ACPI. The LPSS UART block is pretty much same as
used on Intel Baytrail so we can reuse the existing Baytrail setup code.

Add both Broadwell LPSS UART ports to the list of supported devices.

Signed-off-by: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Previously, speakup would always read the non-scrolled part of the VT,
even when the VT is scrolled back with shift-page.  This patch makes
vt.c export screen_pos so that speakup can use it to properly access
the content of the scrolled-back VT.

This was tested with both vgacon and fbcon.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Although n_tty_check_unthrottle() has a valid ldisc reference (since
the tty core gets the ldisc ref in tty_read() before calling the line
discipline read() method), it does not have a valid ldisc reference to
the "other" pty of a pty pair. Since getting an ldisc reference for
tty->link essentially open-codes tty_wakeup(), just replace with the
equivalent tty_wakeup().

Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ioctl(TIOCGETD) retrieves the line discipline id directly from the
ldisc because the line discipline id (c_line) in termios is untrustworthy;
userspace may have set termios via ioctl(TCSETS*) without actually
changing the line discipline via ioctl(TIOCSETD).

However, directly accessing the current ldisc via tty->ldisc is
unsafe; the ldisc ptr dereferenced may be stale if the line discipline
is changing via ioctl(TIOCSETD) or hangup.

Wait for the line discipline reference (just like read() or write())
to retrieve the "current" line discipline id.

Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A small window exists where a tty reopen will observe the tty
just prior to imminent teardown (tty->count == 0); in this case, open()
returns EIO to userspace.

Instead, retry the open after checking for signals and yielding;
this interruptible retry loop allows teardown to commence and initialize
a new tty on retry. Never retry the BSD master pty reopen; there is no
guarantee the pty pair teardown is imminent since the slave file
descriptors may remain open indefinitely.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow a signal to interrupt the wait for a tty reopen; eg., if
the tty has starting final close and is waiting for the device to
drain.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.  Some for SoC-family code under
  drivers/soc, but also some other driver updates that don't belong
  anywhere else.  We also bring in the drivers/reset code through
  arm-soc.

  Some of the larger updates:

   - Qualcomm support for SMEM, SMSM, SMP2P.  All used to communicate
     with other parts of the chip/board on these platforms, all
     proprietary protocols that don't fit into other subsystems and live
     in drivers/soc for now.

   - System bus driver for UniPhier

   - Driver for the TI Wakeup M3 IPC device

   - Power management for Raspberry PI

  + Again a bunch of other smaller updates and patches"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  bus: uniphier: allow only built-in driver
  ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
  MAINTAINERS: Drop Kumar Gala from QCOM
  bus: uniphier-system-bus: add UniPhier System Bus driver
  ARM: bcm2835: add rpi power domain driver
  dt-bindings: add rpi power domain driver bindings
  ARM: bcm2835: Define two new packets from the latest firmware.
  drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
  soc: mediatek: SCPSYS: Add regulator support
  MAINTAINERS: Change QCOM entries
  soc: qcom: smd-rpm: Add existing platform support
  memory/tegra: Add number of TLB lines for Tegra124
  reset: hi6220: fix modular build
  soc: qcom: Introduce WCNSS_CTRL SMD client
  ARM: qcom: select ARM_CPU_SUSPEND for power management
  MAINTAINERS: Add rules for Qualcomm dts files
  soc: qcom: enable smsm/smp2p modular build
  serial: msm_serial: Make config tristate
  soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
  soc: qcom: smsm: Add driver for Qualcomm SMSM
  ...

Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for v4.5.

  Notably there are big refactorings mostly by myself, aimed at getting
  the gpio_chip into a shape that makes me believe I can proceed to
  preserve state for a proper userspace ABI (character device) that has
  already been proposed once, but resulted in the feedback that I need
  to go back and restructure stuff.  So I've been restructuring stuff.
  On the way I ran into brokenness (return code from the get_value()
  callback) and had to fix it.  Also, refactored generic GPIO to be
  simpler.

  Some of that is still waiting to trickle down from the subsystems all
  over the kernel that provide random gpio_chips, I've touched every
  single GPIO driver in the kernel now, oh man I didn't know I was
  responsible for so much...

  Apart from that we're churning along as usual.

  I took some effort to test and retest so it should merge nicely and we
  shook out a couple of bugs in -next.

  Infrastructural changes:

   - In struct gpio_chip, rename the .dev node to .parent to better
     reflect the fact that this is not the GPIO struct device
     abstraction.  We will add that soon so this would be totallt
     confusing.

   - It was noted that the driver .get_value() callbacks was sometimes
     reporting negative -ERR values to the gpiolib core, expecting them
     to be propagated to consumer gpiod_get_value() and gpio_get_value()
     calls.  This was not happening, so as there was a mess of drivers
     returning negative errors and some returning "anything else than
     zero" to indicate that a line was active.  As some would have bit
     31 set to indicate "line active" it clashed with negative error
     codes.  This is fixed by the largeish series clamping values in all
     drivers with !!value to [0,1] and then augmenting the code to
     propagate error codes to consumers.  (Includes some ACKed patches
     in other subsystems.)

   - Add a void *data pointer to struct gpio_chip.  The container_of()
     design pattern is indeed very nice, but we want to reform the
     struct gpio_chip to be a non-volative, stateless business, and keep
     states internal to the gpiolib to be able to hold on to the state
     when adding a proper userspace ABI (character device) further down
     the road.  To achieve this, drivers need a handle at the internal
     state that is not dependent on their struct gpio_chip() so we add
     gpiochip_add_data() and gpiochip_get_data() following the pattern
     of many other subsystems.  All the "use gpiochip data pointer"
     patches transforms drivers to this scheme.

   - The Generic GPIO chip header has been merged into the general
     <linux/gpio/driver.h> header, and the custom header for that
     removed.  Instead of having a separate mm_gpio_chip struct for
     these generic drivers, merge that into struct gpio_chip,
     simplifying the code and removing the need for separate and
     confusing includes.

  Misc improvements:

   - Stabilize the way GPIOs are looked up from the ACPI legacy
     specification.

   - Incremental driver features for PXA, PCA953X, Lantiq (patches from
     the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48

  New drivers:

   - Add a GPIO chip to the ALSA SoC AC97 driver.

   - Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
     but the branch is merged here too to account for infrastructural
     changes).

   - The sx150x driver now supports the sx1502"

* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
  gpio: generic: make bgpio_pdata always visible
  gpiolib: fix chip order in gpio list
  gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
  gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
  gpio: brcmstb: Allow building driver for BMIPS_GENERIC
  gpio: brcmstb: Set endian flags for big-endian MIPS
  gpio: moxart: fix build regression
  gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
  leds: pca9532: use gpiochip data pointer
  leds: tca6507: use gpiochip data pointer
  hid: cp2112: use gpiochip data pointer
  bcma: gpio: use gpiochip data pointer
  avr32: gpio: use gpiochip data pointer
  video: fbdev: via: use gpiochip data pointer
  gpio: pch: Optimize pch_gpio_get()
  Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
  pinctrl: nsp-gpio: use gpiochip data pointer
  pinctrl: vt8500-wmt: use gpiochip data pointer
  pinctrl: exynos5440: use gpiochip data pointer
  pinctrl: at91-pio4: use gpiochip data pointer
  ...