The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).

Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.

See: https://www.exar.com/common/content/document.ashx?id=1587 page 11

Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.

Example of broken console log:

[ 1086.7         Expecting device dev-ttySAC1.device...
[ 1086.[  OK  ] Reached target Paths.
[ 1086.756416] s[  OK  ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[    5.53403[  OK  ] Created slice Root Slice.
[    5.548433] systemd[1]: Create[  OK  ] Created slice User and Session Slice.
[    5.568414] sys[  OK  ] Listening on /dev/initctl Compatibility Named Pipe.
[    5.588388] s[  OK  ] Listening on Delayed Shutdown Socket.
[    5.608376] sy[  OK  ] Listening on Journal Socket (/dev/log).
[    5.628361] [  OK  ] Listening on udev Kernel Socket.
[    5.648357] s[  OK  ] Listening on udev Control Socket.
[    5.668353] s[  OK  ] Listening on Journal Socket.
[    5.688366] systemd[1]: Listeni[  OK  ] Created slice System Slice.
[    5.708393]          Mounting Temporary Directory...
[ 7139.067436]          Starting prepare device daemon...
[ 7139.091726] sy         Starting Generate environment from /etc/profile.d...
[    5.792867] system         Starting Create Static Device Nodes in /dev...
[ 7848.718         Mounting Debug File System...
[ 7848.7384         Mounting Configuration File System...
[    5.852         Starting Apply Kernel Variables...
[    5.8720         Starting Setup Virtual Console...
[ 7848.798         Starting udev Coldplug all Devices...
[ 7848.817         Starting Journal Service...
[  OK  ] Started Journal Service.
[ 7848.854222] s[  OK  ] Reached target Slices.
         Starting Remount Root and Kernel File Systems...
[  OK  ] Mounted Configuration File System.

Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.

When PORT_UNKNOWN is setup probe will fail anyway.

Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"

This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.

Fix both xilinx serial drivers in the tree.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix uart_console_write() kernel-doc build warnings.

Warning(drivers/tty/serial/serial_core.c:1778): No description found for parameter 'putchar'
Warning(drivers/tty/serial/serial_core.c:1778): Excess function parameter 'write' description in 'uart_console_write'

Fixes: 1cfe42b7fd29 ("serial: core: Fix kernel doc for uart_console_write()")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is needed by Bluetooth hci_uart module to be able to change speed
of Bluetooth controller and local UART.

Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull second batch of devicetree updates from Rob Herring:
 "As Grant mentioned in the first devicetree pull request, here is the
  2nd batch of DT changes for 4.1.  The main remaining item here is the
  endianness bindings and related 8250 driver support.

   - DT endianness specification bindings

   - big-endian 8250 serial support

   - DT overlay unittest updates

   - various DT doc updates

   - compile fixes for OF_IRQ=n"

* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  frv: add io{read,write}{16,32}be functions
  mn10300: add io{read,write}{16,32}be functions
  Documentation: DT bindings: add doc for Altera's SoCFPGA platform
  of: base: improve of_get_next_child() kernel-doc
  Doc: dt: arch_timer: discourage clock-frequency use
  of: unittest: overlay: Keep track of created overlays
  of/fdt: fix allocation size for device node path
  serial: of_serial: Support big-endian register accesses
  serial: 8250: Add support for big-endian MMIO accesses
  of: Document {little,big,native}-endian bindings
  of/fdt: Add endianness helper function for early init code
  of: Add helper function to check MMIO register endianness
  of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
  of: add vendor prefix for Artesyn
  of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
  of: OF_IRQ should depend on IRQ_DOMAIN

Pull tty/serial updates from Greg KH:
 "Here's the big tty/serial driver update for 4.1-rc1.

  It was delayed for a bit due to some questions surrounding some of the
  console command line parsing changes that are in here.  There's still
  one tiny regression for people who were previously putting multiple
  console command lines and expecting them all to be ignored for some
  odd reason, but Peter is working on fixing that.  If not, I'll send a
  revert for the offending patch, but I have faith that Peter can
  address it.

  Other than the console work here, there's the usual serial driver
  updates and changes, and a buch of 8250 reworks to try to make that
  driver easier to maintain over time, and have it support more devices
  in the future.

  All of these have been in linux-next for a while"

* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
  n_gsm: Drop unneeded cast on netdev_priv
  sc16is7xx: expose RTS inversion in RS-485 mode
  serial: 8250_pci: port failed after wakeup from S3
  earlycon: 8250: Document kernel command line options
  earlycon: 8250: Fix command line regression
  earlycon: Fix __earlycon_table stride
  tty: clean up the tty time logic a bit
  serial: 8250_dw: only get the clock rate in one place
  serial: 8250_dw: remove useless ACPI ID check
  dmaengine: hsu: move memory allocation to GFP_NOWAIT
  dmaengine: hsu: remove redundant pieces of code
  serial: 8250_pci: add Intel Tangier support
  dmaengine: hsu: add Intel Tangier PCI ID
  serial: 8250_pci: replace switch-case by formula for Intel MID
  serial: 8250_pci: replace switch-case by formula
  tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
  serial: jsm: some off by one bugs
  serial: xuartps: Fix check in console_setup().
  serial: xuartps: Get rid of register access macros.
  serial: xuartps: Fix iobase use.
  ...

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...