linux.git/drivers/tty/serial, branch v5.6-rc4 Linux kernel source tree serial: cpm_uart: call cpm_muram_init before registering console 2020-02-13T20:03:26+00:00 Rasmus Villemoes linux@rasmusvillemoes.dk 2020-02-13T11:43:42+00:00 4508cf76b1ecdf20a456b6b161acbe78f3b23358 Christophe reports that powerpc 8xx silently fails to 5.6-rc1. It turns out I was wrong about nobody relying on the lazy initialization of the cpm/qe muram in commit b6231ea2b3c6 (soc: fsl: qe: drop broken lazy call of cpm_muram_init()). Rather than reinstating the somewhat dubious lazy call (initializing a currently held spinlock, and implicitly doing a GFP_KERNEL under that spinlock), make sure that cpm_muram_init() is called early enough - I thought the calls from the subsys_initcalls were good enough, but when used by console drivers, that's obviously not the case. cpm_muram_init() is safe to call twice (there's an early return if it is already initialized), so keep the call from cpm_init() - in case SERIAL_CPM_CONSOLE=n. Fixes: b6231ea2b3c6 (soc: fsl: qe: drop broken lazy call of cpm_muram_init()) Reported-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> Link: https://lore.kernel.org/r/20200213114342.21712-1-linux@rasmusvillemoes.dk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
Christophe reports that powerpc 8xx silently fails to 5.6-rc1. It turns
out I was wrong about nobody relying on the lazy initialization of the
cpm/qe muram in commit b6231ea2b3c6 (soc: fsl: qe: drop broken lazy
call of cpm_muram_init()).

Rather than reinstating the somewhat dubious lazy call (initializing a
currently held spinlock, and implicitly doing a GFP_KERNEL under that
spinlock), make sure that cpm_muram_init() is called early enough - I
thought the calls from the subsys_initcalls were good enough, but when
used by console drivers, that's obviously not the
case. cpm_muram_init() is safe to call twice (there's an early return
if it is already initialized), so keep the call from cpm_init() - in
case SERIAL_CPM_CONSOLE=n.

Fixes: b6231ea2b3c6 (soc: fsl: qe: drop broken lazy call of cpm_muram_init())
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200213114342.21712-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: qcom_geni_serial: Fix RX cancel command failure 2020-02-12T19:57:38+00:00 satya priya skakit@codeaurora.org 2020-02-11T10:13:02+00:00 679aac5ead2f18d223554a52b543e1195e181811 RX cancel command fails when BT is switched on and off multiple times. To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register instead of SE_GENI_S_CMD_CTRL_REG. As per the HPG update, handle the RX last bit after cancel command and flush out the RX FIFO buffer. Signed-off-by: satya priya <skakit@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
RX cancel command fails when BT is switched on and off multiple times.

To handle this, poll for the cancel bit in SE_GENI_S_IRQ_STATUS register
instead of SE_GENI_S_CMD_CTRL_REG.

As per the HPG update, handle the RX last bit after cancel command
and flush out the RX FIFO buffer.

Signed-off-by: satya priya <skakit@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1581415982-8793-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: 8250: Check UPF_IRQ_SHARED in advance 2020-02-12T19:56:44+00:00 Andy Shevchenko andriy.shevchenko@linux.intel.com 2020-02-11T13:55:59+00:00 7febbcbc48fc92e3f33863b32ed715ba4aff18c4 The commit 54e53b2e8081 ("tty: serial: 8250: pass IRQ shared flag to UART ports") nicely explained the problem: ---8<---8<--- On some systems IRQ lines between multiple UARTs might be shared. If so, the irqflags have to be configured accordingly. The reason is: The 8250 port startup code performs IRQ tests *before* the IRQ handler for that particular port is registered. This is performed in serial8250_do_startup(). This function checks whether IRQF_SHARED is configured and only then disables the IRQ line while testing. This test is performed upon each open() of the UART device. Imagine two UARTs share the same IRQ line: On is already opened and the IRQ is active. When the second UART is opened, the IRQ line has to be disabled while performing IRQ tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself cannot be handled, because the corresponding handler isn't registered, yet. That's because the 8250 code uses a chain-handler and invokes the corresponding port's IRQ handling routines himself. Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't disabled while performing tests and the kernel correctly detects a spurious IRQ. So, adding this flag to the DT probe solves the issue. Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the IRQF_SHARED flag can be set unconditionally as well. Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system: |irq 85: nobody cared (try booting with the "irqpoll" option) | [...] |handlers: |[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt |Disabling IRQ #85 ---8<---8<--- But unfortunately didn't fix the root cause. Let's try again here by moving IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup(). This should fix the similar issue reported for 8250_pnp case. Since this change we don't need to have custom solutions in 8250_aspeed_vuart and 8250_of drivers, thus, drop them. Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support") Reported-by: Li RongQing <lirongqing@baidu.com> Cc: Kurt Kanzenbach <kurt@linutronix.de> Cc: Vikram Pandita <vikram.pandita@ti.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable <stable@vger.kernel.org> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
The commit 54e53b2e8081
  ("tty: serial: 8250: pass IRQ shared flag to UART ports")
nicely explained the problem:

---8<---8<---

On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.

This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling routines himself.

Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.

Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.

Example stack trace by performing `echo 1 > /dev/ttyS2` on a non-patched system:

|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85

---8<---8<---

But unfortunately didn't fix the root cause. Let's try again here by moving
IRQ flag assignment from serial_link_irq_chain() to serial8250_do_startup().

This should fix the similar issue reported for 8250_pnp case.

Since this change we don't need to have custom solutions in 8250_aspeed_vuart
and 8250_of drivers, thus, drop them.

Fixes: 1c2f04937b3e ("serial: 8250: add IRQ trigger support")
Reported-by: Li RongQing <lirongqing@baidu.com>
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20200211135559.85960-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: imx: setup the correct sg entry for tx dma 2020-02-12T19:55:21+00:00 Fugang Duan fugang.duan@nxp.com 2020-02-11T06:16:01+00:00 f76707831829530ffdd3888bebc108aecefccaa0 There has oops as below happen on i.MX8MP EVK platform that has 6G bytes DDR memory. when (xmit->tail < xmit->head) && (xmit->head == 0), it setups one sg entry with sg->length is zero: sg_set_buf(sgl + 1, xmit->buf, xmit->head); if xmit->buf is allocated from >4G address space, and SDMA only support <4G address space, then dma_map_sg() will call swiotlb_map() to do bounce buffer copying and mapping. But swiotlb_map() don't allow sg entry's length is zero, otherwise report BUG_ON(). So the patch is to correct the tx DMA scatter list. Oops: [ 287.675715] kernel BUG at kernel/dma/swiotlb.c:497! [ 287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP [ 287.686075] Modules linked in: [ 287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10 [ 287.696872] Hardware name: FSL i.MX8MP EVK (DT) [ 287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO) [ 287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310 [ 287.711076] lr : swiotlb_map+0x60/0x148 [ 287.714909] sp : ffff800010003c00 [ 287.718221] x29: ffff800010003c00 x28: 0000000000000000 [ 287.723533] x27: 0000000000000040 x26: ffff800011ae0000 [ 287.728844] x25: ffff800011ae09f8 x24: 0000000000000000 [ 287.734155] x23: 00000001b7af9000 x22: 0000000000000000 [ 287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe [ 287.744776] x19: ffff000176409c10 x18: 000000000000002e [ 287.750087] x17: 0000000000000000 x16: 0000000000000000 [ 287.755397] x15: 0000000000000000 x14: 0000000000000000 [ 287.760707] x13: ffff00017f334000 x12: 0000000000000001 [ 287.766018] x11: 00000000001fffff x10: 0000000000000000 [ 287.771328] x9 : 0000000000000003 x8 : 0000000000000000 [ 287.776638] x7 : 0000000000000000 x6 : 0000000000000000 [ 287.781949] x5 : 0000000000200000 x4 : 0000000000000000 [ 287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000 [ 287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000 [ 287.797881] Call trace: [ 287.800328] swiotlb_tbl_map_single+0x1fc/0x310 [ 287.804859] swiotlb_map+0x60/0x148 [ 287.808347] dma_direct_map_page+0xf0/0x130 [ 287.812530] dma_direct_map_sg+0x78/0xe0 [ 287.816453] imx_uart_dma_tx+0x134/0x2f8 [ 287.820374] imx_uart_dma_tx_callback+0xd8/0x168 [ 287.824992] vchan_complete+0x194/0x200 [ 287.828828] tasklet_action_common.isra.0+0x154/0x1a0 [ 287.833879] tasklet_action+0x24/0x30 [ 287.837540] __do_softirq+0x120/0x23c [ 287.841202] irq_exit+0xb8/0xd8 [ 287.844343] __handle_domain_irq+0x64/0xb8 [ 287.848438] gic_handle_irq+0x5c/0x148 [ 287.852185] el1_irq+0xb8/0x180 [ 287.855327] cpuidle_enter_state+0x84/0x360 [ 287.859508] cpuidle_enter+0x34/0x48 [ 287.863083] call_cpuidle+0x18/0x38 [ 287.866571] do_idle+0x1e0/0x280 [ 287.869798] cpu_startup_entry+0x20/0x40 [ 287.873721] rest_init+0xd4/0xe0 [ 287.876949] arch_call_rest_init+0xc/0x14 [ 287.880958] start_kernel+0x420/0x44c [ 287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000) [ 287.890718] ---[ end trace 5bc44c4ab6b009ce ]--- [ 287.895334] Kernel panic - not syncing: Fatal exception in interrupt [ 287.901686] SMP: stopping secondary CPUs [ 288.905607] SMP: failed to stop secondary CPUs 0-1 [ 288.910395] Kernel Offset: disabled [ 288.913882] CPU features: 0x0002,2000200c [ 288.917888] Memory Limit: none [ 288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- Reported-by: Eagle Zhou <eagle.zhou@nxp.com> Tested-by: Eagle Zhou <eagle.zhou@nxp.com> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
There has oops as below happen on i.MX8MP EVK platform that has
6G bytes DDR memory.

when (xmit->tail < xmit->head) && (xmit->head == 0),
it setups one sg entry with sg->length is zero:
	sg_set_buf(sgl + 1, xmit->buf, xmit->head);

if xmit->buf is allocated from >4G address space, and SDMA only
support <4G address space, then dma_map_sg() will call swiotlb_map()
to do bounce buffer copying and mapping.

But swiotlb_map() don't allow sg entry's length is zero, otherwise
report BUG_ON().

So the patch is to correct the tx DMA scatter list.

Oops:
[  287.675715] kernel BUG at kernel/dma/swiotlb.c:497!
[  287.680592] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[  287.686075] Modules linked in:
[  287.689133] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.3-00016-g3fdc4e0-dirty #10
[  287.696872] Hardware name: FSL i.MX8MP EVK (DT)
[  287.701402] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[  287.706199] pc : swiotlb_tbl_map_single+0x1fc/0x310
[  287.711076] lr : swiotlb_map+0x60/0x148
[  287.714909] sp : ffff800010003c00
[  287.718221] x29: ffff800010003c00 x28: 0000000000000000
[  287.723533] x27: 0000000000000040 x26: ffff800011ae0000
[  287.728844] x25: ffff800011ae09f8 x24: 0000000000000000
[  287.734155] x23: 00000001b7af9000 x22: 0000000000000000
[  287.739465] x21: ffff000176409c10 x20: 00000000001f7ffe
[  287.744776] x19: ffff000176409c10 x18: 000000000000002e
[  287.750087] x17: 0000000000000000 x16: 0000000000000000
[  287.755397] x15: 0000000000000000 x14: 0000000000000000
[  287.760707] x13: ffff00017f334000 x12: 0000000000000001
[  287.766018] x11: 00000000001fffff x10: 0000000000000000
[  287.771328] x9 : 0000000000000003 x8 : 0000000000000000
[  287.776638] x7 : 0000000000000000 x6 : 0000000000000000
[  287.781949] x5 : 0000000000200000 x4 : 0000000000000000
[  287.787259] x3 : 0000000000000001 x2 : 00000001b7af9000
[  287.792570] x1 : 00000000fbfff000 x0 : 0000000000000000
[  287.797881] Call trace:
[  287.800328]  swiotlb_tbl_map_single+0x1fc/0x310
[  287.804859]  swiotlb_map+0x60/0x148
[  287.808347]  dma_direct_map_page+0xf0/0x130
[  287.812530]  dma_direct_map_sg+0x78/0xe0
[  287.816453]  imx_uart_dma_tx+0x134/0x2f8
[  287.820374]  imx_uart_dma_tx_callback+0xd8/0x168
[  287.824992]  vchan_complete+0x194/0x200
[  287.828828]  tasklet_action_common.isra.0+0x154/0x1a0
[  287.833879]  tasklet_action+0x24/0x30
[  287.837540]  __do_softirq+0x120/0x23c
[  287.841202]  irq_exit+0xb8/0xd8
[  287.844343]  __handle_domain_irq+0x64/0xb8
[  287.848438]  gic_handle_irq+0x5c/0x148
[  287.852185]  el1_irq+0xb8/0x180
[  287.855327]  cpuidle_enter_state+0x84/0x360
[  287.859508]  cpuidle_enter+0x34/0x48
[  287.863083]  call_cpuidle+0x18/0x38
[  287.866571]  do_idle+0x1e0/0x280
[  287.869798]  cpu_startup_entry+0x20/0x40
[  287.873721]  rest_init+0xd4/0xe0
[  287.876949]  arch_call_rest_init+0xc/0x14
[  287.880958]  start_kernel+0x420/0x44c
[  287.884622] Code: 9124c021 9417aff8 a94363f7 17ffffd5 (d4210000)
[  287.890718] ---[ end trace 5bc44c4ab6b009ce ]---
[  287.895334] Kernel panic - not syncing: Fatal exception in interrupt
[  287.901686] SMP: stopping secondary CPUs
[  288.905607] SMP: failed to stop secondary CPUs 0-1
[  288.910395] Kernel Offset: disabled
[  288.913882] CPU features: 0x0002,2000200c
[  288.917888] Memory Limit: none
[  288.920944] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

Reported-by: Eagle Zhou <eagle.zhou@nxp.com>
Tested-by: Eagle Zhou <eagle.zhou@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 7942f8577f2a ("serial: imx: TX DMA: clean up sg initialization")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/1581401761-6378-1-git-send-email-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial: tegra: Handle RX transfer in PIO mode if DMA wasn't started 2020-02-10T20:32:13+00:00 Dmitry Osipenko digetx@gmail.com 2020-02-09T16:44:15+00:00 1f69a1273b3f204a9c00dc3bbdcc4afcd0787428 It is possible to get an instant RX timeout or end-of-transfer interrupt before RX DMA was started, if transaction is less than 16 bytes. Transfer should be handled in PIO mode in this case because DMA can't handle it. This patch brings back the original behaviour of the driver that was changed by accident by a previous commit, it fixes occasional Bluetooth HW initialization failures which I started to notice recently. Fixes: d5e3fadb7012 ("tty: serial: tegra: Activate RX DMA transfer by request") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20200209164415.9632-1-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
It is possible to get an instant RX timeout or end-of-transfer interrupt
before RX DMA was started, if transaction is less than 16 bytes. Transfer
should be handled in PIO mode in this case because DMA can't handle it.
This patch brings back the original behaviour of the driver that was
changed by accident by a previous commit, it fixes occasional Bluetooth HW
initialization failures which I started to notice recently.

Fixes: d5e3fadb7012 ("tty: serial: tegra: Activate RX DMA transfer by request")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200209164415.9632-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty/serial: atmel: manage shutdown in case of RS485 or ISO7816 mode 2020-02-10T20:26:44+00:00 Nicolas Ferre nicolas.ferre@microchip.com 2020-02-10T15:20:53+00:00 04b5bfe3dc94e64d0590c54045815cb5183fb095 In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions. Prevent the rx restart that is implemented in RS485 or ISO7816 modes when calling atmel_stop_tx() by using the atomic information tasklet_shutdown that is already in place for this purpose. Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences") Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
In atmel_shutdown() we call atmel_stop_rx() and atmel_stop_tx() functions.
Prevent the rx restart that is implemented in RS485 or ISO7816 modes when
calling atmel_stop_tx() by using the atomic information tasklet_shutdown
that is already in place for this purpose.

Fixes: 98f2082c3ac4 ("tty/serial: atmel: enforce tasklet init and termination sequences")
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210152053.8289-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE 2020-02-10T20:26:44+00:00 Daniel Golle daniel@makrotopia.org 2020-02-07T09:53:35+00:00 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 On AR934x this UART is usually not initialized by the bootloader as it is only used as a secondary serial port while the primary UART is a newly introduced NS16550-compatible. In order to make use of the ar933x-uart on AR934x without RTS/CTS hardware flow control, one needs to set the UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this UART is used as primary/console, the bootloader on AR934x typically doesn't set those bits. Setting them explicitely on AR933x should not do any harm, so just set them unconditionally. Tested-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> 
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.

Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up remaining devm_ioremap_nocache() in SGI IOC3 8250 UART driver 2020-02-08T22:19:39+00:00 Linus Torvalds torvalds@linux-foundation.org 2020-02-08T22:19:39+00:00 b0ef7cda8d9be41ba198207c30a037bc470d9aef This is a merge error on my part - the driver was merged into mainline by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux") over a week ago, but nobody apparently noticed that it didn't actually build due to still having a reference to the devm_ioremap_nocache() function, removed a few days earlier through commit 6a1000bd2703 ("Merge tag 'ioremap-5.6' of git://../ioremap"). Apparently this didn't get any build testing anywhere. Not perhaps all that surprising: it's restricted to 64-bit MIPS only, and only with the new SGI_MFD_IOC3 support enabled. I only noticed because the ioremap conflicts in the ARM SoC driver update made me check there weren't any others hiding, and I found this one. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> 
This is a merge error on my part - the driver was merged into mainline
by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux")
over a week ago, but nobody apparently noticed that it didn't actually
build due to still having a reference to the devm_ioremap_nocache()
function, removed a few days earlier through commit 6a1000bd2703 ("Merge
tag 'ioremap-5.6' of git://../ioremap").

Apparently this didn't get any build testing anywhere.  Not perhaps all
that surprising: it's restricted to 64-bit MIPS only, and only with the
new SGI_MFD_IOC3 support enabled.

I only noticed because the ioremap conflicts in the ARM SoC driver
update made me check there weren't any others hiding, and I found this
one.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc 2020-02-08T22:04:19+00:00 Linus Torvalds torvalds@linux-foundation.org 2020-02-08T22:04:19+00:00 eab3540562fb44f830e09492374fcc69a283ce47 Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms: - Nvidia: Fuse support for Tegra194, continued memory controller pieces for Tegra30 - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC - NXP/FSL: i.MX8MP SoC driver pieces - TI Keystone: ring accelerator driver - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs. - Xilinx ZynqMP: feature checking interface for firmware. Mailbox communication for power management - Overall support patch set for cpuidle on more complex hierarchies (PSCI-based) and misc cleanups, refactorings of Marvell, TI, other platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits) drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists MAINTAINERS: Add brcmstb PCIe controller entry soc/tegra: fuse: Unmap registers once they are not needed anymore soc/tegra: fuse: Correct straps' address for older Tegra124 device trees soc/tegra: fuse: Warn if straps are not ready soc/tegra: fuse: Cache values of straps and Chip ID registers memory: tegra30-emc: Correct error message for timed out auto calibration memory: tegra30-emc: Firm up hardware programming sequence memory: tegra30-emc: Firm up suspend/resume sequence soc/tegra: regulators: Do nothing if voltage is unchanged memory: tegra: Correct reset value of xusb_hostr soc/tegra: fuse: Add APB DMA dependency for Tegra20 bus: tegra-aconnect: Remove PM_CLK dependency dt-bindings: mediatek: add MT6765 power dt-bindings soc: mediatek: cmdq: delete not used define memory: tegra: Add support for the Tegra194 memory controller memory: tegra: Only include support for enabled SoCs memory: tegra: Support DVFS on Tegra186 and later ... 
Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms:

   - Nvidia: Fuse support for Tegra194, continued memory controller
     pieces for Tegra30

   - NXP/FSL: Refactorings of QuickEngine drivers to support
     ARM/ARM64/PPC

   - NXP/FSL: i.MX8MP SoC driver pieces

   - TI Keystone: ring accelerator driver

   - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.

   - Xilinx ZynqMP: feature checking interface for firmware. Mailbox
     communication for power management

   - Overall support patch set for cpuidle on more complex hierarchies
     (PSCI-based)

  and misc cleanups, refactorings of Marvell, TI, other platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
  drivers: soc: xilinx: Use mailbox IPI callback
  dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
  drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
  MAINTAINERS: Add brcmstb PCIe controller entry
  soc/tegra: fuse: Unmap registers once they are not needed anymore
  soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
  soc/tegra: fuse: Warn if straps are not ready
  soc/tegra: fuse: Cache values of straps and Chip ID registers
  memory: tegra30-emc: Correct error message for timed out auto calibration
  memory: tegra30-emc: Firm up hardware programming sequence
  memory: tegra30-emc: Firm up suspend/resume sequence
  soc/tegra: regulators: Do nothing if voltage is unchanged
  memory: tegra: Correct reset value of xusb_hostr
  soc/tegra: fuse: Add APB DMA dependency for Tegra20
  bus: tegra-aconnect: Remove PM_CLK dependency
  dt-bindings: mediatek: add MT6765 power dt-bindings
  soc: mediatek: cmdq: delete not used define
  memory: tegra: Add support for the Tegra194 memory controller
  memory: tegra: Only include support for enabled SoCs
  memory: tegra: Support DVFS on Tegra186 and later
  ...
Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux 2020-01-31T19:28:31+00:00 Linus Torvalds torvalds@linux-foundation.org 2020-01-31T19:28:31+00:00 c5951e7c8ee5cb04b8b41c32bf567b90117a2124 Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ... 
Pull MIPS changes from Paul Burton:
 "Nothing too big or scary in here:

   - Support mremap() for the VDSO, primarily to allow CRIU to restore
     the VDSO to its checkpointed location.

   - Restore the MIPS32 cBPF JIT, after having reverted the enablement
     of the eBPF JIT for MIPS32 systems in the 5.5 cycle.

   - Improve cop0 counter synchronization behaviour whilst onlining CPUs
     by running with interrupts disabled.

   - Better match FPU behaviour when emulating multiply-accumulate
     instructions on pre-r6 systems that implement IEEE754-2008 style
     MACs.

   - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
     to take advantage of instructions introduced by r2.

   - Support for the Ingenic X1000 SoC & the really nice little CU Neo
     development board that's using it.

   - Support for WMAC on GARDENA Smart Gateway devices.

   - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
     preparation for introducing IP35 (Origin 3*) support.

   - Various Kconfig & Makefile cleanups"

* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
  MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
  MIPS: Loongson64: Disable exec hazard
  MIPS: Loongson64: Bump ISA level to MIPSR2
  MIPS: Make DIEI support as a config option
  MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
  MIPS: asm: local: add barriers for Loongson
  MIPS: Loongson64: Select mac2008 only feature
  MIPS: Add MAC2008 Support
  Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
  MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
  MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
  MIPS: generic: don't unconditionally select PINCTRL
  MIPS: don't explicitly select LIBFDT in Kconfig
  MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
  MIPS: SGI-IP30: Check for valid pointer before using it
  MIPS: syscalls: fix indentation of the 'SYSNR' message
  MIPS: boot: fix typo in 'vmlinux.lzma.its' target
  MIPS: fix indentation of the 'RELOCS' message
  dt-bindings: Document loongson vendor-prefix
  MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
  ...