linux.git/drivers/tty/serial/8250, branch v4.7

Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2016-05-21T03:57:27+00:00

Pull tty and serial driver updates from Greg KH:
 "Here's the large TTY and Serial driver update for 4.7-rc1.

  A few new serial drivers are added here, and Peter has fixed a bunch
  of long-standing bugs in the tty layer and serial drivers as normal.
  Full details in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
  MAINTAINERS: 8250: remove website reference
  serial: core: Fix port mutex assert if lockdep disabled
  serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
  tty: vt, finish looping on duplicate
  tty: vt, return error when con_startup fails
  QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
  serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
  serial: 8250dw: Add device HID for future AMD UART controller
  Fix OpenSSH pty regression on close
  serial: mctrl_gpio: add IRQ locking
  serial: 8250: Integrate Fintek into 8250_base
  serial: mps2-uart: add support for early console
  serial: mps2-uart: add MPS2 UART driver
  dt-bindings: document the MPS2 UART bindings
  serial: sirf: Use generic uart-has-rtscts DT property
  serial: sirf: Introduce helper variable struct device_node *np
  serial: mxs-auart: Use generic uart-has-rtscts DT property
  serial: imx: Use generic uart-has-rtscts DT property
  doc: DT: Add Generic Serial Device Tree Bindings
  serial: 8250: of: Make tegra_serial_handle_break() static
  ...

Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma

2016-05-19T18:47:18+00:00

Pull dmaengine updates from Vinod Koul:
 "This time round the update brings in following changes:

   - new tegra driver for ADMA device

   - support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
     Central Direct Memory Access Engine and few updates to this driver

   - new cyclic capability to sun6i and few updates

   - slave-sg support in bcm2835

   - updates to many drivers like designware, hsu, mv_xor, pxa, edma,
     qcom_hidma & bam"

* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
  dmaengine: ioatdma: disable relaxed ordering for ioatdma
  dmaengine: of_dma: approximate an average distribution
  dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
  dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
  dmaengine: qcom_hidma: add support for object hierarchy
  dmaengine: qcom_hidma: add debugfs hooks
  dmaengine: qcom_hidma: implement lower level hardware interface
  dmaengine: vdma: Add clock support
  Documentation: DT: vdma: Add clock support for dmas
  dmaengine: vdma: Add config structure to differentiate dmas
  MAINTAINERS: Update Tegra DMA maintainers
  dmaengine: tegra-adma: Add support for Tegra210 ADMA
  Documentation: DT: Add binding documentation for NVIDIA ADMA
  dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
  Documentation: DT: vdma: update binding doc for AXI CDMA
  dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
  Documentation: DT: vdma: update binding doc for AXI DMA
  dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
  dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
  dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
  ...

serial: 8250_dw: fix wrong logic in dw8250_check_lcr()

2016-05-03T23:10:38+00:00

Commit cdcea058e510 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.

The __raw_readq/__raw_writeq is introduced by commit bca2092d7897 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.

So for 64BIT && !PORT_OCTEON, we better to use coincident write function.

Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang 
Signed-off-by: Greg Kroah-Hartman

serial: 8250dw: Add device HID for future AMD UART controller

2016-05-01T20:22:54+00:00

Add device HID AMDI0020 to match the AMD ACPI Vendor ID (AMDI) as
registered in http://www.uefi.org/acpi_id_list, and the UART
controller on future AMD paltform will use the HID instead of AMD0020.

Signed-off-by: Wang Hongcheng 
Acked-by: Andy Shevchenko 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: Integrate Fintek into 8250_base

2016-04-30T16:26:55+00:00

The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).

This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.

This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.

Reported-by: Peter Hurley 
Signed-off-by: Ricardo Ribalda Delgado 
Reviewed-by: Peter Hurley 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: of: Make tegra_serial_handle_break() static

2016-04-30T16:26:55+00:00

This function is not used outside the file, so it can be static.

Signed-off-by: Thierry Reding 
Signed-off-by: Greg Kroah-Hartman

serial: omap8250: Terminate rx dma only for flushes

2016-04-30T16:26:55+00:00

DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.

Signed-off-by: Peter Hurley 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

serial: 8250: Extract IIR logic steering from rx dma

2016-04-30T16:26:55+00:00

Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.

Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.

Signed-off-by: Peter Hurley 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

serial: omap8250: Simplify rx dma completion interface

2016-04-30T16:26:55+00:00

Extract the operation (restarting new rx dma) performed when error
argument is true.

Signed-off-by: Peter Hurley 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman

serial: omap8250: Drop rx buffer sync

2016-04-30T16:26:55+00:00

commit 27c310c5c312 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.

Signed-off-by: Peter Hurley 
Reviewed-by: Heikki Krogerus 
Signed-off-by: Greg Kroah-Hartman