linux.git/drivers/target/iscsi, branch v3.13

iscsi-target: Fix incorrect np->np_thread NULL assignment

2013-12-19T08:18:25+00:00

When shutting down a target there is a race condition between
iscsit_del_np() and __iscsi_target_login_thread().
The latter sets the thread pointer to NULL, and the former
tries to issue kthread_stop() on that pointer without any
synchronization.

This patch moves the np->np_thread NULL assignment into
iscsit_del_np(), after kthread_stop() has completed. It also
removes the signal_pending() + np_state check, and only
exits when kthread_should_stop() is true.

Reported-by: Hannes Reinecke 
Cc:  #3.12+
Signed-off-by: Nicholas Bellinger

iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set

2013-12-11T18:59:57+00:00

This patch changes special case handling for ISCSI_OP_SCSI_CMD
where an initiator sends a zero length Expected Data Transfer
Length (EDTL), but still sets the WRITE and/or READ flag bits
when no payload transfer is requested.

Many, many moons ago two special cases where added for an ancient
version of ESX that has long since been fixed, so instead of adding
a new special case for the reported bug with a Broadcom 57800 NIC,
go ahead and always strip off the incorrect WRITE + READ flag bits.

Also, avoid sending a reject here, as RFC-3720 does mandate this
case be handled without protocol error.

Reported-by: Witold Bazakbal <865perl@wp.pl>
Tested-by: Witold Bazakbal <865perl@wp.pl>
Cc:  #3.1+
Signed-off-by: Nicholas Bellinger

iscsi-target: return -EINVAL on oversized configfs parameter

2013-12-11T18:59:33+00:00

The iSCSI CHAP auth parameters are already copied with respect for
the destination buffer size.  Return -EINVAL instead of silently
truncating the input.

Signed-off-by: Eric Seppanen 
Signed-off-by: Nicholas Bellinger

Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending

2013-11-22T18:52:03+00:00

Pull SCSI target updates from Nicholas Bellinger:
 "Things have been quiet this round with mostly bugfixes, percpu
  conversions, and other minor iscsi-target conformance testing changes.

  The highlights include:

   - Add demo_mode_discovery attribute for iscsi-target (Thomas)
   - Convert tcm_fc(FCoE) to use percpu-ida pre-allocation
   - Add send completion interrupt coalescing for ib_isert
   - Convert target-core to use percpu-refcounting for se_lun
   - Fix mutex_trylock usage bug in iscsit_increment_maxcmdsn
   - tcm_loop updates (Hannes)
   - target-core ALUA cleanups + prep for v3.14 SCSI Referrals support (Hannes)

  v3.14 is currently shaping to be a busy development cycle in target
  land, with initial support for T10 Referrals and T10 DIF currently on
  the roadmap"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits)
  iscsi-target: chap auth shouldn't match username with trailing garbage
  iscsi-target: fix extract_param to handle buffer length corner case
  iscsi-target: Expose default_erl as TPG attribute
  target_core_configfs: split up ALUA supported states
  target_core_alua: Make supported states configurable
  target_core_alua: Store supported ALUA states
  target_core_alua: Rename ALUA_ACCESS_STATE_OPTIMIZED
  target_core_alua: spellcheck
  target core: rename (ex,im)plict -> (ex,im)plicit
  percpu-refcount: Add percpu-refcount.o to obj-y
  iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN
  iscsi-target: Convert iscsi_session statistics to atomic_long_t
  target: Convert se_device statistics to atomic_long_t
  target: Fix delayed Task Aborted Status (TAS) handling bug
  iscsi-target: Reject unsupported multi PDU text command sequence
  ib_isert: Avoid duplicate iscsit_increment_maxcmdsn call
  iscsi-target: Fix mutex_trylock usage in iscsit_increment_maxcmdsn
  target: Core does not need blkdev.h
  target: Pass through I/O topology for block backstores
  iser-target: Avoid using FRMR for single dma entry requests
  ...

iscsi-target: chap auth shouldn't match username with trailing garbage

2013-11-21T06:03:57+00:00

In iSCSI negotiations with initiator CHAP enabled, usernames with
trailing garbage are permitted, because the string comparison only
checks the strlen of the configured username.

e.g. "usernameXXXXX" will be permitted to match "username".

Just check one more byte so the trailing null char is also matched.

Signed-off-by: Eric Seppanen 
Cc:  #3.1+
Signed-off-by: Nicholas Bellinger

iscsi-target: fix extract_param to handle buffer length corner case

2013-11-21T06:03:28+00:00

extract_param() is called with max_length set to the total size of the
output buffer.  It's not safe to allow a parameter length equal to the
buffer size as the terminating null would be written one byte past the
end of the output buffer.

Signed-off-by: Eric Seppanen 
Cc:  #3.1+
Signed-off-by: Nicholas Bellinger

iscsi-target: Expose default_erl as TPG attribute

2013-11-20T19:57:18+00:00

This patch exposes default_erl as a TPG attribute so that it may be
set TPG wide in demo-mode, but still allow the existing NodeACL
attribute to be overridden on a per initiator basis.

Reported-by: Arshad Hussain 
Signed-off-by: Nicholas Bellinger

iscsi-target: Do not reject non-immediate CmdSNs exceeding MaxCmdSN

2013-11-20T05:39:21+00:00

This patch changes iscsit_sequence_cmd() logic to no longer reject
non-immediate CmdSNs that exceed MaxCmdSN with a protocol error,
but instead silently ignore them.

This is done to correctly follow RFC-3720 Section 3.2.2.1:

   For non-immediate commands, the CmdSN field can take any
   value from ExpCmdSN to MaxCmdSN inclusive.  The target MUST silently
   ignore any non-immediate command outside of this range or non-
   immediate duplicates within the range.

Reported-by: Santosh Kulkarni 
Signed-off-by: Nicholas Bellinger

iscsi-target: Convert iscsi_session statistics to atomic_long_t

2013-11-20T05:38:52+00:00

This patch converts a handful of iscsi_session statistics to type
atomic_long_t, instead of using iscsi_session->session_stats_lock
when incrementing these values.

More importantly, go ahead and drop the spinlock usage within
iscsit_setup_scsi_cmd(), iscsit_check_dataout_hdr(),
iscsit_send_datain(), and iscsit_build_rsp_pdu() fast-path code.

(Squash in Roland's  target: Remove write-only stats fields and lock
from struct se_node_acl)

Signed-off-by: Nicholas Bellinger

iscsi-target: Reject unsupported multi PDU text command sequence

2013-11-13T22:33:24+00:00

This patch adds a check to reject text commands with F_BIT=0 ||
C_BIT=1, as multi PDU text command sequences are currently
unsupported.

This avoids the case where a text command received with F_BIT=0,
was generating a text response with F_BIT=1 which is a protocol
error according to RFC-3720 Section 10.11.1.

Reported-by: Arshad Hussain 
Signed-off-by: Nicholas Bellinger