This is a driver for the Amlogic Meson SPIFC (SPI flash controller),
which is one of the two SPI controllers available on the SoC. It
doesn't support DMA and has a 64-byte unified transmit/receive buffer.

The device is optimized for interfacing with SPI NOR memories and
allows the execution of standard operations such as read, page
program, sector erase, etc. in a simplified way, toggling a bit in a
dedicated register. The driver doesn't use those predefined commands
and relies only on custom transfers.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add support for the Synchronous Peripheral Flash Interface (SPFI) master
controller found on IMG SoCs.  The SPFI controller supports 5 chip-select
lines and single/dual/quad mode SPI transfers.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

In order to facilitate understanding, rockchip SPI controller IP design
looks similar in its registers to designware. But IC implementation
is different from designware, So we need a dedicated driver for Rockchip
RK3XXX SoCs integrated SPI. The main differences:

- dma request line: rockchip SPI controller have two DMA request line
  for tx and rx.

- Register offset:
                  RK3288        dw
  SPI_CTRLR0      0x0000        0x0000
  SPI_CTRLR1      0x0004        0x0004
  SPI_SSIENR      0x0008        0x0008
  SPI_MWCR        NONE          0x000c
  SPI_SER         0x000c        0x0010
  SPI_BAUDR       0x0010        0x0014
  SPI_TXFTLR      0x0014        0x0018
  SPI_RXFTLR      0x0018        0x001c
  SPI_TXFLR       0x001c        0x0020
  SPI_RXFLR       0x0020        0x0024
  SPI_SR          0x0024        0x0028
  SPI_IPR         0x0028        NONE
  SPI_IMR         0x002c        0x002c
  SPI_ISR         0x0030        0x0030
  SPI_RISR        0x0034        0x0034
  SPI_TXOICR      NONE          0x0038
  SPI_RXOICR      NONE          0x003c
  SPI_RXUICR      NONE          0x0040
  SPI_MSTICR      NONE          0x0044
  SPI_ICR         0x0038        0x0048
  SPI_DMACR       0x003c        0x004c
  SPI_DMATDLR     0x0040        0x0050
  SPI_DMARDLR     0x0044        0x0054
  SPI_TXDR        0x0400        NONE
  SPI_RXDR        0x0800        NONE
  SPI_IDR         NONE          0x0058
  SPI_VERSION     NONE          0x005c
  SPI_DR          NONE          0x0060

- register configuration:
  such as SPI_CTRLRO in rockchip SPI controller:
    cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET)
        | (CR0_SSD_ONE << CR0_SSD_OFFSET);
    cr0 |= (rs->n_bytes << CR0_DFS_OFFSET);
    cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET);
    cr0 |= (rs->tmode << CR0_XFM_OFFSET);
    cr0 |= (rs->type << CR0_FRF_OFFSET);
  For more information, see RK3288 chip manual.

- Wait for idle: Must ensure that the FIFO data has been sent out
  before the next transfer.

Signed-off-by: addy ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add driver for Cadence SPI controller. This is used in Xilinx Zynq.

Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>