Pull ARM SoC fixes from Arnd Bergmann:
 "The code fixes in this round are all for the Texas Instruments OMAP
  platform, addressing several regressions related to the ti-sysc
  interconnect changes that was merged in linux-5.11 and one recently
  introduced RCU usage warning.

  Tero Kristo updates his maintainer file entries as he is changing to a
  new employer.

  The other changes are for devicetree files across eight different
  platforms:

  TI OMAP:
   - multiple gpio related one-line fixes

  Allwinner/sunxi:
   - ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
   - soc: sunxi: mbus: Remove DE2 display engine compatibles

  NXP lpc32xx:
   - ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL

  STMicroelectronics stm32
   - multiple minor fixes for DHCOM/DHCOR boards

  NXP Layerscape:
   - Fix DCFG address range on LS1046A SoC

  Amlogic meson:
   - fix reboot issue on odroid C4
   - revert an ethernet change that caused a regression
   - meson-g12: Set FL-adj property value

  Rockchip:
   - multiple minor fixes on 64-bit rockchip machines

  Qualcomm:
   - Regression fixes for Lenovo Yoga touchpad and for interconnect
     configuration
   - Boot fixes for 'LPASS' clock configuration on two machines"

* tag 'arm-soc-fixes-v5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (31 commits)
  ARM: dts: lpc32xx: Revert set default clock rate of HCLK PLL
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  arm64: dts: ls1046a: fix dcfg address range
  soc: sunxi: mbus: Remove DE2 display engine compatibles
  arm64: dts: meson: switch TFLASH_VDD_EN pin to open drain on Odroid-C4
  Revert "arm64: dts: amlogic: add missing ethernet reset ID"
  arm64: dts: rockchip: Disable display for NanoPi R2S
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
  ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
  ARM: dts: stm32: Fix GPIO hog names on DHCOM
  ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
  ARM: dts: stm32: Disable WP on DHCOM uSD slot
  ARM: dts: stm32: Connect card-detect signal on DHCOM
  ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
  arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
  ...

One fix for a phy-mode ethernet issue, and one to fix the display output on
SoCs with the Display Engine 2

* tag 'sunxi-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
  soc: sunxi: mbus: Remove DE2 display engine compatibles

Link: https://lore.kernel.org/r/f8298059-f9ca-43b4-9e29-35bc0e0c9b15.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Pull OpenRISC fix from Stafford Horne:
 "Fix config dependencies for Litex SOC driver causing issues on um"

* tag 'for-linus' of git://github.com/openrisc/linux:
  soc: litex: Properly depend on HAS_IOMEM

The LiteX SOC controller driver makes use of IOMEM functions like
devm_platform_ioremap_resource(), which are only available if
CONFIG_HAS_IOMEM is defined.

This causes the driver to be enable under make ARCH=um allyesconfig,
even though it won't build.

By adding a dependency on HAS_IOMEM, the driver will not be enabled on
architectures which don't support it.

Fixes: 22447a99c97e ("drivers/soc/litex: add LiteX SoC Controller driver")
Signed-off-by: David Gow <davidgow@google.com>
[shorne@gmail.com: Fix typo in commit message pointed out in review]
Signed-off-by: Stafford Horne <shorne@gmail.com>

Pull ARM SoC fixes from Arnd Bergmann:
 "These are the current arm-soc bug fixes for linux-5.11. I already
  merged a larger set that just came in during the past three days but
  has not had much exposure in linux-next, but this is the subset I
  merged last week.

  Most of these are for the NXP i.MX platform (descriptions from their
  pull request):

   - Fix pcf2127 reset for imx7d-flex-concentrator board.
   - Fix i.MX6 suspend with Thumb-2 kernel.
   - Fix ethernet-phy address issue on imx6qdl-sr-som board.
   - Fix GPIO3 `gpio-ranges` on i.MX8MP.
   - Select SOC_BUS for IMX_SCU driver to fix build issue.
   - Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
     #pwm-cells conversion.
   - Fix duplicated bus node name for i.MX8MN SoC.
   - Fix reset register offset on LS1028A SoC.
   - Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
     index consistent with previous kernel version.
   - Selecting ARM_GIC_V3 on non-CP15 processors to fix one build
     failure with i.MX8M SoC driver.
   - Fix typos with status property on imx6qdl-kontron-samx6i board.
   - Fix duplicated regulator-name on imx6qdl-gw52xx board.

  Aside from i.MX, the bugfixes are all over the place:

   - Coccinelle found a refcount imbalance on integrator
   - defconfig fix for TI K3
   - A boot regression fix for ST ux500
   - A code preemption fix for the optee driver
   - USB DMA regression on Broadcom Stingray
   - A bogus boot time warning fix for at91 code"

* tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  MAINTAINERS: Include bcm2835 subsequents into search
  arm64: dts: broadcom: Fix USB DMA address translation for Stingray
  drivers: soc: atmel: add null entry at the end of at91_soc_allowed_list[]
  drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs
  tee: optee: replace might_sleep with cond_resched
  firmware: imx: select SOC_BUS to fix firmware build
  arm64: dts: imx8mp: Correct the gpio ranges of gpio3
  ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
  ARM: imx: build suspend-imx6.S with arm instruction set
  ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
  ARM: dts: ux500: Reserve memory carveouts
  arm64: defconfig: Drop unused K3 SoC specific options
  bus: arm-integrator-lm: Add of_node_put() before return statement
  ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
  ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
  ARM: imx: fix imx8m dependencies
  ARM: dts: tbs2910: rename MMC node aliases
  arm64: dts: ls1028a: fix the offset of the reset register
  arm64: dts: imx8mn: Fix duplicate node name
  ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight

Fixes for omaps for v5.11-rc cycle

The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:

- The omap_prm reset driver needs to clear any reset bits deasserted by
  the bootloader or kexec boot for the three reset bit cases. Otherwise
  we can have an oops with accelerators starting to boot with potentially
  unconfigured MMU for example

- Custom kernel configs are not automatically selecting simple-pm-bus
  driver that we now need to probe interconnects so we need to select it
  always

- We are not passing legacy platform data in auxdata with simple-pm-bus
  like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
  it can pass it to of_platform_populate()

Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places

And then we have few device specific fixes:

- We need to remove legacy spi-cs-hig for gta04 display to work, and
  set the gpio to active low

- Omap1 specific ohci-omap needs to call gpio_free()

- Droid4 needs to use padconf interrupt for the slider as the edge
  gpio interrupts may be lost for deeper idle states

* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
  drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
  ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
  ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
  ARM: dts; gta04: SPI panel chip select is active low
  soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
  ARM: OMAP1: OSK: fix ohci-omap breakage
  DTS: ARM: gta04: remove legacy spi-cs-high to make display work again

Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The DE2 display engine hardware takes physical addresses that do not
need PHYS_BASE subtracted. As a result, they should not be present
on the mbus driver match list. Remove them.

This was tested on the A83T, along with the patch allowing the DMA
range map to be non-NULL and restores a working display.

Fixes: b4bdc4fbf8d0 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210115175831.1184260-2-paul.kocialkowski@bootlin.com

of_match_node() calls __of_match_node() which loops though the entries of
matches array. It stops when condition:
(matches->name[0] || matches->type[0] || matches->compatible[0]) is
false. Thus, add a null entry at the end of at91_soc_allowed_list[]
array.

Fixes: caab13b49604 ("drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs")
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Since at91_soc_init is called unconditionally from atmel_soc_device_init,
we get the following warning on all non AT91 SoCs:
	" AT91: Could not find identification node"

Fix the same by filtering with allowed AT91 SoC list.

Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201211135846.1334322-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>