After commit 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on
until late_initcall_sync") was applied, the Tegra210 Jetson TX1 board
failed to boot. Looking into this issue, before this commit was applied,
if any of the Tegra power-domains were in 'on' state when the kernel
booted, they were being turned off by the genpd core before any driver
had chance to request them. This was purely by luck and a consequence of
the power-domains being turned off earlier during boot. After this
commit was applied, any power-domains in the 'on' state are kept on for
longer during boot and therefore, may never transitioned to the off
state before they are requested/used. The hang on the Tegra210 Jetson
TX1 is caused because devices in some power-domains are accessed without
the power-domain being turned off and on, indicating that the
power-domain is not in a completely on state.

>From reviewing the Tegra PMC driver code, if a power-domain is in the
'on' state there is no guarantee that all the necessary clocks
associated with the power-domain are on and even if they are they would
not have been requested via the clock framework and so could be turned
off later. Some power-domains also have a 'clamping' register that needs
to be configured as well. In short, if a power-domain is already 'on' it
is difficult to know if it has been configured correctly. Given that the
power-domains happened to be switched off during boot previously, to
ensure that they are in a good known state on boot, fix this by
switching off any power-domains that are on initially when registering
the power-domains with the genpd framework.

Note that commit 05cfb988a4d0 ("soc/tegra: pmc: Initialise resets
associated with a power partition") updated the
tegra_powergate_of_get_resets() function to pass the 'off' to ensure
that the resets for the power-domain are in the correct state on boot.
However, now that we may power off a domain on boot, if it is on, it is
better to move this logic into the tegra_powergate_add() function so
that there is a single place where we are handling the initial state of
the power-domain.

Fixes: a38045121bf4 ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250731121832.213671-1-jonathanh@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull pmdomain updates from Ulf Hansson:
 "pmdomain core:
   - Leave powered-on genpds on until ->sync_state() or late_initcall_sync
   - Export a common ->sync_state() helper for genpd providers
   - Add generic ->sync_state() support
   - Add a bus/driver for genpd provider-devices
   - Introduce dev_pm_genpd_is_on() for consumers

  pmdomain providers:
   - cpuidle-psci: Drop redundant ->sync_state() support
   - cpuidle-riscv-sbi: Drop redundant ->sync_state() support
   - imx: Set ISI panic write for imx8m-blk-ctrl
   - qcom: Add support for Glymur and Milos RPMh power-domains
   - qcom: Use of_genpd_sync_state() for power-domains
   - rockchip: Add support for the RK3528 variant
   - samsung: Fix splash-screen handover by enforcing a ->sync_state()
   - sunxi: Add support for Allwinner A523's PCK600 power-controller
   - tegra: Opt-out from genpd's common ->sync_state() support for pmc
   - thead: Instantiate a GPU power sequencer via the auxiliary bus
   - renesas: Move init to postcore_initcalls
   - xilinx: Move ->sync_state() support to firmware driver
   - xilinx: Use of_genpd_sync_state() for power-domains

  pmdomain consumers:
   - remoteproc: imx_rproc: Fixup the detect/attach procedure for
     pre-booted cores"

* tag 'pmdomain-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (44 commits)
  pmdomain: qcom: rpmhpd: Add Glymur RPMh Power Domains
  dt-bindings: power: rpmpd: Add Glymur power domains
  remoteproc: imx_rproc: detect and attach to pre-booted remote cores
  remoteproc: imx_rproc: skip clock enable when M-core is managed by the SCU
  pmdomain: core: introduce dev_pm_genpd_is_on()
  pmdomain: ti: Select PM_GENERIC_DOMAINS
  pmdomain: sunxi: sun20i-ppu: change to tristate and enable for ARCH_SUNXI
  pmdomain: sunxi: add driver for Allwinner A523's PCK-600 power controller
  pmdomain: sunxi: sun20i-ppu: add A523 support
  pmdomain: samsung: Fix splash-screen handover by enforcing a sync_state
  cpuidle: riscv-sbi: Drop redundant sync_state support
  cpuidle: psci: Drop redundant sync_state support
  pmdomain: core: Leave powered-on genpds on until sync_state
  pmdomain: core: Leave powered-on genpds on until late_initcall_sync
  pmdomain: core: Default to use of_genpd_sync_state() for genpd providers
  driver core: Add dev_set_drv_sync_state()
  pmdomain: core: Add common ->sync_state() support for genpd providers
  driver core: Export get_dev_from_fwnode()
  firmware: xilinx: Use of_genpd_sync_state()
  firmware: xilinx: Don't share zynqmp_pm_init_finalize()
  ...

Pull SoC defconfig updates from Arnd Bergmann:
 "As usual, more drivers get enabled in the defconfigs, to support newly
  added hardware drivers.

  There is one change for Tegra that modifies the Kconfig file at the
  same time, and the NXP arm32 defconfigs get a refresh"

* tag 'soc-defconfig-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
  arm: multi_v7_defconfig: Enable TPS65219 regulator
  arm: omap2plus_defconfig: Enable TPS65219 regulator
  arm64: defconfig: Enable Tegra241 and Tegra264
  riscv: defconfig: spacemit: enable sdhci driver for K1 SoC
  riscv: defconfig: Enable PWM support for SpacemiT K1 SoC
  riscv: defconfig: Remove CONFIG_SND_SOC_STARFIVE=m
  arm64: defconfig: Enable Tegra HSP and BPMP
  ARM: imx_v6_v7_defconfig: select CONFIG_USB_HSIC_USB3503
  ARM: imx_v6_v7_defconfig: select CONFIG_INPUT_PWM_BEEPER
  ARM: imx_v6_v7_defconfig: cleanup with savedefconfig
  ARM: mxs_defconfig: select new drivers used by imx28-amarula-rmm
  ARM: mxs_defconfig: Cleanup mxs_defconfig
  arm64: defconfig: enable further Rockchip platform drivers
  arm64: defconfig: enable Samsung PMIC over ACPM
  arm64: defconfig: enable Maxim max77759 driver
  ARM: configs: sama5_defconfig: Select CONFIG_WILC1000_SDIO
  ARM: shmobile: defconfig: Refresh for v6.16-rc2
  arm64: defconfig: Enable RZ/V2H(P) USB2 PHY controller reset driver
  arm64: defconfig: add S32G RTC module support
  arm64: defconfig: Drop unneeded unselectable sound drivers
  ...

soc/tegra: Updates for v6.17-rc1

The bulk of this is the addition of Tegra264 support for various low-
level components. This also adds fabric descriptors for the new Tegra254
and Tegra264 chips.

* tag 'tegra-for-6.17-soc' of https://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: cbb: Add support for CBB fabrics in Tegra254
  soc/tegra: cbb: Add support for CBB fabrics in Tegra264
  soc/tegra: cbb: Support HW lookup to get timed out target address
  soc/tegra: cbb: Improve handling for per SoC fabric data
  soc/tegra: cbb: Make error interrupt enable and status per SoC
  soc/tegra: cbb: Change master/slave to initiator/target
  soc/tegra: cbb: Clear ERR_FORCE register with ERR_STATUS
  soc/tegra: Add Tegra264 APBMISC compatible string
  soc/tegra: pmc: Add Tegra264 support
  soc/tegra: Enable support for Tegra264

Link: https://lore.kernel.org/r/20250711220943.2389322-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add support for CBB 2.0 based fabrics in Tegra254 SoC using ACPI.
Fabrics reporting errors are: C2C, GPU and Display_Cluster. Tegra254
uses a hardware based lookup to get target node address, so the
target_map tables for each fabric are no longer needed.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add support for CBB 2.0 based fabrics in Tegra264 SoC using DT. Fabrics
reporting errors are: SYSTEM, TOP0, UPHY0 and VISION.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Add support for hardware based lookup to get the address of the timed
out target node. This features is added in upcoming SoCs and avoids the
need for creating per fabric target_map tables in the driver.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Improve handling for the per SoC fabrics and targets.
The below changes make them more flexible and ready for future SoC's.
- Added SoC prefix to Fabric_ID enums.
- Rename *lookup_target_timeout() to *sw_lookup_target_timeout() to
  make it separate from HW based lookup function to be added later.
- Moved target_map within fabric_lookup table to make it easy to
  check whether SW vs HW lookup is supported and handle accordingly.
- Slight improvements to some error prints.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Make the error interrupt enable and error status fields as per SoC. Both
of these fields can change for different SoC's. Moving them to per SoC
data helps to set or clear the required bits only for a SoC.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Change usage of 'Master/Slave' to 'Initiator/Target' as per the new
convention.

Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>