* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
  omap: complete removal of machine_desc.io_pg_offst and .phys_io
  omap: UART: fix wakeup registers for OMAP24xx UART2
  omap: Fix spotty MMC voltages
  ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
  serial: omap-serial: fix signess error
  OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
  omap: dma: Fix buffering disable bit setting for omap24xx
  omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
  OMAP3: PM: fix scratchpad memory accesses for off-mode
  omap4: pandaboard: enable the ehci port on pandaboard
  omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
  omap4: pandaboard: remove unused hsmmc definition
  OMAP: McBSP: Remove null omap44xx ops comment
  OMAP: McBSP: Swap CLKS source definition
  OMAP: McBSP: Fix CLKR and FSR signal muxing
  OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
  OMAP: control: move plat-omap/control.h to mach-omap2/control.h
  OMAP: split plat-omap/common.c
  OMAP: McBSP: implement functional clock switching via clock framework
  OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
  ...

Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
  serial8250: ratelimit "too much work" error
  serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
  serial: abstraction for 8250 legacy ports
  serial/imx: check that the buffer is non-empty before sending it out
  serial: mfd: add more baud rates support
  jsm: Remove the uart port on errors
  Alchemy: Add UART PM methods.
  8250: allow platforms to override PM hook.
  altera_uart: Don't use plain integer as NULL pointer
  altera_uart: Fix missing prototype for registering an early console
  altera_uart: Fixup type usage of port flags
  altera_uart: Make it possible to use Altera UART and 8250 ports together
  altera_uart: Add support for different address strides
  altera_uart: Add support for getting mapbase and IRQ from resources
  altera_uart: Add support for polling mode (IRQ-less)
  serial: Factor out uart_poll_timeout() from 8250 driver
  serial: mark the 8250 driver as maintained
  serial: 8250: Don't delay after transmitter is ready.
  tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
  vcs: invoke the vt update callback when /dev/vcs* is written to
  ...

And while we are at it allow it to fail to find one. Without this the IRQ
option will cause the 3110 driver to fail on 0.7 SFI firmware.

Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch adds UART serial port support for S5P6450 SoC.
The S5P6450 has 6 UARTs, so adds resource of UART4 and UART5.
And to fix membase which is in serial/samsung.c is from Ben Dooks.

Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>

This patch adds driver support for OMAP2/3/4 high speed UART.

The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (226 commits)
  ARM: 6323/1: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
  ARM: 6324/1: cam60: move cam60_spi_devices to .init.data
  ARM: 6322/1: imx/pca100: Fix name of spi platform data
  ARM: 6321/1: fix syntax error in main Kconfig file
  ARM: 6297/1: move U300 timer to dynamic clock lookup
  ARM: 6296/1: clock U300 intcon and timer properly
  ARM: 6295/1: fix U300 apb_pclk split
  ARM: 6306/1: fix inverted MMC card detect in U300
  ARM: 6299/1: errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID
  ARM: 6294/1: etm: do a dummy read from OSSRR during initialization
  ARM: 6292/1: coresight: add ETM management registers
  ARM: 6288/1: ftrace: document mcount formats
  ARM: 6287/1: ftrace: clean up mcount assembly indentation
  ARM: 6286/1: fix Thumb-2 decompressor broken by "Auto calculate ZRELADDR"
  ARM: 6281/1: video/imxfb.c: allow usage without BACKLIGHT_CLASS_DEVICE
  ARM: 6280/1: imx: Fix build failure when including <mach/gpio.h> without <linux/spinlock.h>
  ARM: S5PV210: Fix on missing s3c-sdhci card detection method for hsmmc3
  ARM: S5P: Fix on missing S5P_DEV_FIMC in plat-s5p/Kconfig
  ARM: S5PV210: Override FIMC driver name on Aquila board
  ARM: S5PC100: enable FIMC on SMDKC100
  ...

Fix up conflicts in arch/arm/mach-{s5pc100,s5pv210}/cpu.c due to
different subsystem 'setname' calls, and trivial port types in
include/linux/serial_core.h

This is a PCI & UART driver, which suppors both PIO and DMA mode
UART operation. It has 3 identical UART ports and one internal
DMA controller.

Current FW will export 4 pci devices for hsu: 3 uart ports and 1
dma controller, each has one IRQ line. And we need to discuss the
device model, one PCI device covering whole HSU should be a better
model, but there is a problem of how to export the 4 IRQs info

Current driver set the highest baud rate to 2746800bps, which is
easy to scale down to 115200/230400.... To suport higher baud rate,
we need add special process, change DLAB/DLH/PS/DIV/MUL registers
all together.

921600 is the highest baud rate that has been tested with Bluetooth
modem connected to HSU port 0. Will test more when there is right
BT firmware.

Current version contains several work around for A0's Silicon bugs

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

At the moment there is only one platform type supported and there is is
hard wired, but with these changes the infrastructure is now there for
anyone else to provide methods for their hardware.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This device is used by some of the Intel MID platforms. It's not similar
enough to the MAX3100 to use the same driver.

At this point the driver is specific to the platform and not generalised.
We will fix that later.

Signed-off-by: jianwei.yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This driver enable the max3110 device, it can be used as
a system console. the IRQ needs be enabled if user want a
better performance. MRST max3110 works in 3.684MHz clock,
which supports 230400 as its maximum rate.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>