Pull SCSI fixes from James Bottomley:
 "Two small fixes, both in drivers.

  The mptsas one is really fixing an error path issue where it can leave
  the misc driver loaded even though the sas driver fails to initialize"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix double free of dsd_list during driver load
  scsi: mpt3sas: Fix in error path

On driver load, scsi_add_host() can fail. This triggers the free path to
call qla2x00_mem_free() multiple times. This causes NULL pointer access of
ha->base_qpair. Add check before access.

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
 IP: [<ffffffffc118f73c>] qla2x00_mem_free+0x51c/0xcb0 [qla2xxx]
 PGD 8000001fcfe4a067 PUD 1fc8f0a067 PMD 0
 Oops: 0000 [#1] SMP
 RIP: 0010:[<ffffffffc118f73c>]  [<ffffffffc118f73c>] qla2x00_mem_free+0x51c/0xcb0 [qla2xxx]
 RSP: 0018:ffff8ace97a93a30  EFLAGS: 00010246
 RAX: 0000000000000000 RBX: ffff8ace8efd0000 RCX: 000000000000488f
 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
 RBP: ffff8ace97a93a60 R08: 000000000001f040 R09: ffffffff8678209b
 R10: ffff8acf7d6df040 R11: ffffc591c0fcc980 R12: ffffffff87034800
 R13: ffff8acf0e3cc740 R14: ffff8ace8efd0000 R15: 00000000fffffff4
 FS:  00007f4cf5449740(0000) GS:ffff8acf7d6c0000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000030 CR3: 0000001fc2f6c000 CR4: 00000000007607e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  [<ffffffff86781f18>] ? kobject_put+0x28/0x60
  [<ffffffffc119a59c>] qla2x00_probe_one+0x19fc/0x3040 [qla2xxx]

Fixes: efeda3bf912f ("scsi: qla2xxx: Move resource to allow code reuse")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20231016101749.5059-1-njavali@marvell.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The driver should be deregistered as misc driver after PCI registration
failure.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20231015114529.10725-1-thenzl@redhat.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Commit ff48b37802e5 ("scsi: Do not attempt to rescan suspended devices")
modified scsi_rescan_device() to avoid attempting rescanning a suspended
device. However, the modification added a check to verify that a SCSI
device is in the running state without checking if the device request
queue (in the case of block device) is also running, thus allowing the
exectuion of internal requests. Without checking the device request
queue, commit ff48b37802e5 fix is incomplete and deadlocks on resume can
still happen. Use blk_queue_pm_only() to check if the device request
queue allows executing commands in addition to checking the SCSI device
state.

Reported-by: Petr Tesarik <petr@tesarici.cz>
Fixes: ff48b37802e5 ("scsi: Do not attempt to rescan suspended devices")
Cc: stable@vger.kernel.org
Tested-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>

Pull SCSI fixes from James Bottomley:
 "Three fixes, all in drivers.

  The fnic one is the most extensive because the little used user
  initiated device reset path never tagged the command and adding a tag
  is rather involved. The other two fixes are smaller and more obvious"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: zfcp: Fix a double put in zfcp_port_enqueue()
  scsi: fnic: Fix sg_reset success path
  scsi: target: core: Fix deadlock due to recursive locking

Pull ATA fixes from Damien Le Moal:
 "A larger than usual set of fixes for 6.6-rc4 due to the unexpected
  number of fixes needed to address ATA disks suspend/resume issues.

  In more detail:

   - Add missing additionalProperties on child nodes to the pata-common
     DT bindings (Rob)

   - Fix handling of the REPORT SUPPORTED OPERATION CODES command to
     ignore reserved bits (Niklas)

   - Increase port multiplier soft reset timeout to accomodate slow
     devices and avoid issues on wakeup (Matthias)

   - A couple of minor code fixes to avoid compilation warnings in
     libata-core and libata-eh (me)

   - Many patches from me to address suspend/resume issues, and in
     particular a potential deadlock on resume due to the SCSI disk
     driver resume operation not being synchronized with libata EH port
     resume handling.

     This is addressed by changing the scsi disk driver disk start/stop
     control to allow libata to execute disk suspend (spin down) and
     resume (spin up) on its own during system suspend/resume. Runtime
     suspend/resume control remains with the SCSI disk driver.

     Other fixes include:
      - Fix libata power management request issuing to avoid races
      - Establish a link between ATA ports and SCSI devices to order PM
        operations
      - Fix device removal to avoid issues with driver rmmod removal
      - Fix synchronization of libata device rescan and SCSI disk resume
        operation
      - Remove libsas PM operations as suspend/resume is handled
        directly by the sas controller resume
      - Fix the SCSI disk driver to not issue commands to suspended
        disks, thus avoiding potential system lock-up on resume"

* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
  ata: libata-eh: Fix compilation warning in ata_eh_link_report()
  ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
  scsi: sd: Do not issue commands to suspended disks on shutdown
  ata: libata-core: Do not register PM operations for SAS ports
  ata: libata-scsi: Fix delayed scsi_rescan_device() execution
  scsi: Do not attempt to rescan suspended devices
  ata: libata-scsi: Disable scsi device manage_system_start_stop
  scsi: sd: Differentiate system and runtime start/stop management
  ata: libata-scsi: link ata port and scsi device
  ata: libata-core: Fix port and device removal
  ata: libata-core: Fix ata_port_request_pm() locking
  ata: libata-sata: increase PMP SRST timeout to 10s
  ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
  dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes

If an error occurs when resuming a host adapter before the devices
attached to the adapter are resumed, the adapter low level driver may
remove the scsi host, resulting in a call to sd_remove() for the
disks of the host. This in turn results in a call to sd_shutdown() which
will issue a synchronize cache command and a start stop unit command to
spindown the disk. sd_shutdown() issues the commands only if the device
is not already runtime suspended but does not check the power state for
system-wide suspend/resume. That is, the commands may be issued with the
device in a suspended state, which causes PM resume to hang, forcing a
reset of the machine to recover.

Fix this by tracking the suspended state of a disk by introducing the
suspended boolean field in the scsi_disk structure. This flag is set to
true when the disk is suspended is sd_suspend_common() and resumed with
sd_resume(). When suspended is true, sd_shutdown() is not executed from
sd_remove().

Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi_rescan_device() takes a scsi device lock before executing a device
handler and device driver rescan methods. Waiting for the completion of
any command issued to the device by these methods will thus be done with
the device lock held. As a result, there is a risk of deadlocking within
the power management code if scsi_rescan_device() is called to handle a
device resume with the associated scsi device not yet resumed.

Avoid such situation by checking that the target scsi device is in the
running state, that is, fully capable of executing commands, before
proceeding with the rescan and bailout returning -EWOULDBLOCK otherwise.
With this error return, the caller can retry rescaning the device after
a delay.

The state check is done with the device lock held and is thus safe
against incoming suspend power management operations.

Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>

The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.

For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.

Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.

Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull SCSI fixes from James Bottomley:
 "A single fix for libata: older devices don't support command duration
  limits (CDL) and some don't support report opcodes, meaning there's no
  way to tell if they support the command or not.

  Reduce the problems of incorrectly using CDL commands on older devices
  by checking SCSI spec compliance at SPC-5 (the spec which introduced
  the command) before turning on CDL"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: ata: Do no try to probe for CDL on old drives