linux.git/drivers/scsi/libsas, branch v4.20

scsi: libsas: fix a race condition when smp task timeout

2018-09-26T01:20:23+00:00

When the lldd is processing the complete sas task in interrupt and set the
task stat as SAS_TASK_STATE_DONE, the smp timeout timer is able to be
triggered at the same time. And smp_task_timedout() will complete the task
wheter the SAS_TASK_STATE_DONE is set or not. Then the sas task may freed
before lldd end the interrupt process. Thus a use-after-free will happen.

Fix this by calling the complete() only when SAS_TASK_STATE_DONE is not
set. And remove the check of the return value of the del_timer(). Once the
LLDD sets DONE, it must call task->done(), which will call
smp_task_done()->complete() and the task will be completed and freed
correctly.

Reported-by: chenxiang 
Signed-off-by: Jason Yan 
CC: John Garry 
CC: Johannes Thumshirn 
CC: Ewan Milne 
CC: Christoph Hellwig 
CC: Tomas Henzl 
CC: Dan Williams 
CC: Hannes Reinecke 
Reviewed-by: Hannes Reinecke 
Reviewed-by: John Garry 
Reviewed-by: Johannes Thumshirn 
Signed-off-by: Martin K. Petersen

scsi: libsas: check the ata device status by ata_dev_enabled()

2018-09-26T01:20:23+00:00

When ata device IDENTIFY failed, the ata device status is ATA_DEV_UNKNOWN. The
libata reported like:

[113518.620433] ata5.00: qc timeout (cmd 0xec)
[113518.653646] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x4)

But libsas verifies the device status by ata_dev_disabled(), which skipped
ATA_DEV_UNKNOWN. This will make libsas think the ata device probing succeed
the device cannot be actually brought up. And even the new bcast of this
device will be considered as flutter and will not probe this device again.

Change ata_dev_disabled() to !ata_dev_enabled() so that libsas can deal with
this if the ata device probe failed. New bcasts can let us try to probe the
device again and bring it up if it is fine to IDENTIFY.

Tested-by: Zhou Yupeng 
Signed-off-by: Jason Yan 
CC: John Garry 
CC: Johannes Thumshirn 
CC: Ewan Milne 
CC: Christoph Hellwig 
CC: Tomas Henzl 
CC: Dan Williams 
CC: Hannes Reinecke 
Reviewed-by: John Garry 
Reviewed-by: Hannes Reinecke 
Reviewed-by: Johannes Thumshirn 
Reviewed-by: Christoph Hellwig 
Signed-off-by: Martin K. Petersen

scsi: libsas: always unregister the old device if going to discover new

2018-09-26T01:20:23+00:00

If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.

And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.

Signed-off-by: Jason Yan 
CC: chenxiang 
CC: John Garry 
CC: Johannes Thumshirn 
CC: Ewan Milne 
CC: Christoph Hellwig 
CC: Tomas Henzl 
CC: Dan Williams 
CC: Hannes Reinecke 
Reviewed-by: Johannes Thumshirn 
Reviewed-by: Hannes Reinecke 
Signed-off-by: Martin K. Petersen

scsi: libsas: make the lldd_port_deformed method optional

2018-09-26T01:20:23+00:00

Now LLDDs have to implement lldd_port_deformed method otherwise NULL
dereference will happen. Make it optional and remove the dummy implementation
in hisi_sas.

Signed-off-by: Jason Yan 
CC: John Garry 
CC: Johannes Thumshirn 
CC: Ewan Milne 
CC: Christoph Hellwig 
CC: Tomas Henzl 
CC: Dan Williams 
CC: Hannes Reinecke 
Acked-by: John Garry 
Reviewed-by: Hannes Reinecke 
Reviewed-by: Johannes Thumshirn 
Reviewed-by: Christoph Hellwig 
Signed-off-by: Martin K. Petersen

scsi: read host_busy via scsi_host_busy()

2018-06-26T16:53:26+00:00

No functional change.

Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.

Cc: Omar Sandoval ,
Cc: "Martin K. Petersen" ,
Cc: James Bottomley ,
Cc: Christoph Hellwig ,
Cc: Don Brace 
Cc: Kashyap Desai 
Cc: Mike Snitzer 
Cc: Hannes Reinecke 
Cc: Laurence Oberman 
Cc: Bart Van Assche 

Signed-off-by: Ming Lei 
Reviewed-by: Bart Van Assche 
Signed-off-by: Martin K. Petersen

scsi: libsas: dynamically allocate and free ata host

2018-06-20T02:02:25+00:00

Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced
refcounting to ata_host and will increase or decrease the refcount when
adding or deleting transport ATA port.

Now the ata host for libsas is embedded in domain_device, and the ->kref
member is not initialized. Afer we add ata transport class, ata_host_get()
will be called when adding transport ATA port and a warning will be
triggered as below:

refcount_t: increment on 0; use-after-free.
WARNING: CPU: 2 PID: 103 at
lib/refcount.c:153 refcount_inc+0x40/0x48 ......  Call trace:
 refcount_inc+0x40/0x48
 ata_host_get+0x10/0x18
 ata_tport_add+0x40/0x120
 ata_sas_tport_add+0xc/0x14
 sas_ata_init+0x7c/0xc8
 sas_discover_domain+0x380/0x53c
 process_one_work+0x12c/0x288
 worker_thread+0x58/0x3f0
 kthread+0xfc/0x128
 ret_from_fork+0x10/0x18

And also when removing transport ATA port ata_host_put() will be called and
another similar warning will be triggered. If the refcount decreased to
zero, the ata host will be freed. But this ata host is only part of
domain_device, it cannot be freed directly.

So we have to change this embedded static ata host to a dynamically
allocated ata host and initialize the ->kref member. To use ata_host_get()
and ata_host_put() in libsas, we need to move the declaration of these
functions to the public libata.h and export them.

Fixes: b6240a4df018 ("scsi: libsas: add transport class for ATA devices")
Signed-off-by: Jason Yan 
CC: John Garry 
CC: Taras Kondratiuk 
CC: Tejun Heo 
Acked-by: Tejun Heo 
Signed-off-by: Martin K. Petersen

scsi: libsas: remove irq save in sas_ata_qc_issue()

2018-06-20T02:02:25+00:00

Since commit 312d3e56119a ("[SCSI] libsas: remove ata_port.lock management
duties from lldds") the sas_ata_qc_issue() function unlocks the
ata_port.lock and disables interrupts before doing so.  That lock is always
taken with disabled interrupts so at this point, the interrupts are already
disabled. There is no need to disable the interrupts before the unlock
operation because they are already disabled.  Restoring the interrupt state
later does not change anything because they were disabled and remain
disabled. Therefore remove the operations which do not change the
behaviour.

Fixes: 312d3e56119a ("[SCSI] libsas: remove ata_port.lock management duties from lldds")
Signed-off-by: Sebastian Andrzej Siewior 
Acked-by: Dan Williams 
Reviewed-by: John Garry 
Signed-off-by: Martin K. Petersen

treewide: kzalloc() -> kcalloc()

2018-06-12T23:19:22+00:00

The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

        kzalloc(a * b, gfp)

with:
        kcalloc(a * b, gfp)

as well as handling cases of:

        kzalloc(a * b * c, gfp)

with:

        kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kzalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kzalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kzalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kzalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kzalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kzalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kzalloc(sizeof(THING) * C2, ...)
|
  kzalloc(sizeof(TYPE) * C2, ...)
|
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook

scsi: libsas: add transport class for ATA devices

2018-04-18T23:32:51+00:00

Now ata devices attached with sas controller do not have transport
class, so that we can not see any information of these ata devices in
/sys/class/ata_port(or ata_link or ata_device).

Add transport class for the ata devices attached with sas controller.
The /sys/class directory will show the infomation of the ata devices
as follows:

localhost:/sys/class # ls ata*
ata_device:
dev1.0  dev2.0

ata_link:
link1  link2

ata_port:
ata1  ata2

No functional change of the device scanning and io path. The ata
transport class was deleted when destroying the sas devices.

Signed-off-by: Jason Yan 
CC: Dan Williams 
CC: Tejun Heo 
Acked-by: Tejun Heo 
Signed-off-by: Martin K. Petersen

Merge branch 'fixes' into misc

2018-04-04T00:38:39+00:00

Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"

Merge is non-trivial and has been verified by Qlogic (Cavium)

Signed-off-by: James E.J. Bottomley