This adds clock framework support to the rtc-sh driver. With this in place, platforms can default to leaving the clock disabled rather than placing it in the always enabled state. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Modify the sh_rtc driver to use set_irq_wake() during suspend and resume. These functions are used to enable the rtc interrupts in the interrupt controller so the rtc can be used to wakeup the system from suspend. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Flag that the SuperH RTC supports wakeup. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modifies invalid time handling in the SuperH RTC driver. Instead of zeroing the returned value at read-out time we just return an error code and reset invalid values during probe. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modifies the SuperH RTC driver to only enable carry interrupts when needed. So by default no interrupts are enabled with this patch. Without this patch a suspending system will most likely wake up by the carry interrupt regardless if the alarm interrupt has been enabled or not. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for single IRQ hardware to the sh-rtc driver. This is useful for processors with limited interrupt masking support such as sh7750 and sh7780. With this patch in place we can add logic to the intc code that merges all RTC vectors into a single linux interrupt with proper masking/unmasking support. Specify a single IRQ in the platform data to use this new shared IRQ feature. Separate Periodic/Carry/Alarm IRQs are still supported. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the power of 2 check on frequencies down into individual rtc drivers This is to allow for non power of 2 real time clock periodic interrupts such as those on the pxa27x to be found in the new pxa27x-rtc driver Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bunch of irq checking misuses. Most drivers were getting irq via platform_get_irq(), which returns -ENXIO or r->start. rtc-cmos.c is special. It is using PNP and platform bindings. Hopefully nobody is using PNP IRQ 0 for RTC. So the changes should be safe. rtc-sh.c is using platform_get_irq, but was storing a result into an unsigned type, then was checking for < 0. This is fixed now. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits) sh: Move SH-4 CPU headers down one more level. sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected. sh: Migrate common board headers to mach-common/. sh: Move the CPU definition headers from asm/ to cpu/. serial: sh-sci: Add support SCIF of SH7723 video: add sh_mobile_lcdc platform flags video: remove unused sh_mobile_lcdc platform data sh: remove consistent alloc cruft sh: add dynamic crash base address support sh: reduce Migo-R smc91x overruns sh: Fix up some merge damage. Fix debugfs_create_file's error checking method for arch/sh/mm/ Fix debugfs_create_dir's error checking method for arch/sh/kernel/ sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board sh: Use sh7720 GPIO on magicpanelr2 board sh: Add sh7720 pinmux code sh: Use sh7203 GPIO on rsk7203 board sh: Add sh7203 pinmux code sh: Use sh7723 GPIO on AP325RXA board sh: Add sh7723 pinmux code ...