The MFD part is merged into v5.8-rc1, thus remove BROKEN dependency. Signed-off-by: Axel Lin <axel.lin@ingics.com> Link: https://lore.kernel.org/r/20200616135030.1163660-1-axel.lin@ingics.com Signed-off-by: Mark Brown <broonie@kernel.org>
Linux 5.8-rc1
PFUZE100_SWB_REG is not proper for sw1a/sw2, because enable_mask/enable_reg
is not correct. On PFUZE3000, sw1a/sw2 should be the same as sw1a/sw2 on
pfuze100 except that voltages are not linear, so add new PFUZE3000_SW_REG
and pfuze3000_sw_regulator_ops which like the non-linear PFUZE100_SW_REG
and pfuze100_sw_regulator_ops.
Fixes: 1dced996ee70 ("regulator: pfuze100: update voltage setting for pfuze3000 sw1a")
Reported-by: Christophe Meynard <Christophe.Meynard@ign.fr>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1592171648-8752-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pickable ranges mapping function never used range min selector. Thus
existing drivers broke when proper linear_ranges functionality was taken
in use. Fix this for now just by ignoring the minimum selector.
Fixes: 60ab7f4153b6 ("regulator: use linear_ranges helper")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20200612090225.GA3243@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 99f75ce66619 ("regulator: da9063: fix suspend") converted
the regulators to use a common (corrected) suspend bit setting but
one of regulators (LDO9) slipped through the crack.
This means that the original problem was not fixed for LDO9 and
also leads to a warning found by the test robot.
da9063-regulator.c:515:3: warning: initialized field overwritten
Fix this by converting that regulator too like the others.
Fixes: 99f75ce66619 ("regulator: da9063: fix suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Link: https://lore.kernel.org/r/1591959073-16792-1-git-send-email-martin.fuzzey@flowbird.group
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 4ffea5e083f8 ("regulator: max8998: Add charger regulator")
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200530130314.GA73557@d7d8dbfb64ff
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new trace points for the start and end of enabling bypass on a regulator, to allow monitoring of when regulators are moved into bypass and how long that takes. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200529152216.9671-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
Hi! This patchset is another attempt to fix the regulator coupling on Exynos5800/5422 SoCs. Here are links to the previous attempts: https://lore.kernel.org/linux-samsung-soc/20191008101709.qVNy8eijBi0LynOteWFMnTg4GUwKG599n6OyYoX1Abs@z/ https://lore.kernel.org/lkml/20191017102758.8104-1-m.szyprowski@samsung.com/ https://lore.kernel.org/linux-pm/cover.1589528491.git.viresh.kumar@linaro.org/ https://lore.kernel.org/linux-pm/20200528131130.17984-1-m.szyprowski@samsung.com/ The problem is with "vdd_int" regulator coupled with "vdd_arm" on Odroid XU3/XU4 boards family. "vdd_arm" is handled by CPUfreq. "vdd_int" is handled by devfreq. CPUfreq initialized quite early during boot and it starts changing OPPs and "vdd_arm" value. Sometimes CPU activity during boot goes down and some low-frequency OPPs are selected, what in turn causes lowering "vdd_arm". This happens before devfreq applies its requirements on "vdd_int". Regulator balancing code reduces "vdd_arm" voltage value, what in turn causes lowering "vdd_int" value to the lowest possible value. This is much below the operation point of the wcore bus, which still runs at the highest frequency. The issue was hard to notice because in the most cases the board managed to boot properly, even when the regulator was set to lowest value allowed by the regulator constraints. However, it caused some random issues, which can be observed as "Unhandled prefetch abort" or low USB stability. Adding more and more special cases to the generic code has been rejected, so the only way to ensure the desired behavior on Exynos5800-based SoCs is to make a custom regulator coupler driver. Best regards, Marek Szyprowski Patch summary: Marek Szyprowski (2): regulator: extract voltage balancing code to separate function soc: samsung: Add simple voltage coupler for Exynos5800 arch/arm/mach-exynos/Kconfig | 1 + drivers/regulator/core.c | 49 ++++++++------- drivers/soc/samsung/Kconfig | 3 + drivers/soc/samsung/Makefile | 1 + .../soc/samsung/exynos-regulator-coupler.c | 59 +++++++++++++++++++ include/linux/regulator/coupler.h | 8 +++ 6 files changed, 101 insertions(+), 20 deletions(-) create mode 100644 drivers/soc/samsung/exynos-regulator-coupler.c -- 2.17.1 base-commit: 8f3d9f354286745c751374f5f1fcafee6b3f3136