Pull MMC updates from Chris Ball:
 "MMC highlights for 3.15:

  Core:
   - CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
   - DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
   - Add GPIO descriptor based slot-gpio card detect API

  Drivers:
   - dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
   - mmci: Support HW busy detection on ux500
   - omap: Support MMC_ERASE
   - omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
   - rtsx: Support pre-req/post-req async
   - sdhci: Add support for Realtek RTS5250 controllers
   - sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
   - sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
   - sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"

* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
  mmc: sdhci-acpi: Intel SDIO has broken card detect
  mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
  mmc: sdhci-msm: Add platform_execute_tuning implementation
  mmc: sdhci-msm: Initial support for Qualcomm chipsets
  mmc: sdhci-msm: Qualcomm SDHCI binding documentation
  sdhci: only reprogram retuning timer when flag is set
  mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
  mmc: sdhci: Allow for irq being shared
  mmc: sdhci-acpi: Add device id 80860F16
  mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
  mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
  mmc: slot-gpio: Split out CD IRQ request into a separate function
  mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
  Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
  mmc: sdhci-spear: use generic card detection gpio support
  mmc: sdhci-spear: remove support for power gpio
  mmc: sdhci-spear: simplify resource handling
  mmc: sdhci-spear: fix platform_data usage
  mmc: sdhci-spear: fix error handling paths for DT
  mmc: sdhci-bcm-kona: fix build errors when built-in
  ...

On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Add support for S2MPA01 voltage and current regulator.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add a regulator driver for the BCM590xx PMU voltage regulators.
The driver supports LDOs and DCDCs in normal mode only. There is
no support for low-power mode or power sequencing.

Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.

Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@linaro.org>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>