Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for the v4.4 development cycle.

  The only changes hitting outside drivers/gpio are in the pin control
  subsystem and these seem to have settled nicely in linux-next.

  Development mistakes and catfights are nicely documented in the
  reverts as you can see.  The outcome of the ABI fight is that we're
  working on a chardev ABI for GPIO now, where hope to show results for
  the v4.5 kernel.

  Summary of changes:

  GPIO core:
   - Define and handle flags for open drain/open collector and open
     source/open emitter, also know as "single-ended" configurations.
   - Generic request/free operations that handle calling out to the
     (optional) pin control backend.
   - Some refactoring related to an ABI change that did not happen, yet
     provide useful.
   - Added a real-time compliance checklist.  Many GPIO chips have
     irqchips, and need to think this over with the RT patches going
     upstream.
   - Restructure, fix and clean up Kconfig menus a bit.

  New drivers:
   - New driver for AMD Promony.
   - New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
     ISA-style.  Very retro.

  Subdriver changes:
   - OMAP changes to handle real time requirements.
   - Handle trigger types for edge and level IRQs on PL061 properly.  As
     this hardware is very common it needs to set a proper example for
     others to follow.
   - Some container_of() cleanups.
   - Delete the unused MSM driver in favor of the driver that is
     embedded inside the pin control driver.
   - Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
     targets.
   - A consolidated IT87xx driver replacing the earlier very specific
     IT8761e driver.
   - Handle the TI TCA9539 in the PCA953x driver.  Also handle ACPI
     devices in this subdriver.
   - Drop xilinx arch dependencies as these FPGAs seem to profilate over
     a few different architectures.  MIPS and ARM come to mind"

* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
  gpio: fix up SPI submenu
  gpio: drop surplus I2C dependencies
  gpio: drop surplus X86 dependencies
  gpio: dt-bindings: document the official use of "ngpios"
  gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
  gpio / ACPI: Allow shared GPIO event to be read via operation region
  gpio: group port-mapped I/O drivers in a menu
  gpio: Add ACCES 104-IDIO-16 driver maintainer entry
  gpio: zynq: Document interrupt-controller DT binding
  gpio: xilinx: Drop architecture dependencies
  gpio: generic: Revert to old error handling in bgpio_map
  gpio: add a real time compliance notes
  Revert "gpio: add a real time compliance checklist"
  gpio: Add GPIO support for the ACCES 104-IDIO-16
  gpio: driver for AMD Promontory
  gpio: xlp: Convert to use gpiolib irqchip helpers
  gpio: add a real time compliance checklist
  gpio/xilinx: enable for MIPS
  gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
  gpiolib: Split GPIO flags parsing and GPIO configuration
  ...

Pull pin control updates from Linus Walleij:
 "This is the big bulk of pin control changes for the v4.4 kernel
  development cycle.  Development pace is high in pin control again this
  merge window.  28 contributors, 83 patches.

  It hits a few sites outside the pin control subsystem:

   - Device tree bindings in Documentation (as usual)
   - MAINTAINERS
   - drivers/base/* for the "init" state handling by Doug Anderson.
     This has been ACKed by Greg.
   - drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
     in the USB subsystem.  This has been ACKed by both Greg and Felipe.
   - arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
     through the ARM SoC tree but ended up here.

  This time I am using Geert Uytterhoeven as submaintainer for SH PFC
  since the are three-four people working in parallel with new Renesas
  ASICs.

  Summary of changes:

  Infrastructure:

   - Doug Anderson wrote a patch adding an "init" state different from
     the "default" state for pin control state handling in the core
     framework.  This is applied before the driver's probe() call if
     defined and takes precedence over "default".  If both are defined,
     "init" will be applied *before* probe() and "default" will be
     applied *after* probe().

  Significant subdriver improvements:

   - SH PFC is switched to getting GPIO ranges from the device tree
     ranges property on DT platforms.
   - Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
   - Got rid of SH PFC hardcoded IRQ numbers.
   - Allwinner sunxi external interrupt through the "r" controller.
   - Moved the Cygnus driver to use DT-provided GPIO ranges.

  New drivers:

   - Atmel PIO4 pin controller for the SAMA4D2 family

  New subdrivers:

   - Rockchip RK3036 subdriver
   - Renesas SH PFC R8A7795 subdriver
   - Allwinner sunxi A83T PIO subdriver
   - Freescale i.MX7d iomux lpsr subdriver
   - Marvell Berlin BG4CT subdriver
   - SiRF Atlas 7 step B SoC subdriver
   - Intel Broxton SoC subdriver

  Apart from this, the usual slew if syntactic and semantic fixes"

* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
  pinctrl: pinconf: remove needless loop
  pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
  pinctrl: zynq: fix UTF-8 errors
  pinctrl: zynq: Initialize early
  pinctrl: at91: add missing of_node_put
  pinctrl: tegra-xusb: Correct lane mux options
  pinctrl: intel: Add Intel Broxton pin controller support
  pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
  pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
  drivers/pinctrl: Add the concept of an "init" state
  pinctrl: uniphier: set input-enable before pin-muxing
  pinctrl: cygnus: Add new compatible string for gpio controller driver
  pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
  pinctrl: cygnus: Optional DT property to support pin mappings
  pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
  pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
  pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
  pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
  pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
  usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
  ...

This removes a needless loop which was caught in pinconf.c.

Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.

The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long
(it would break the indentation in drivers/pinctrl/Makefile),
so rename it into CONFIG_PINCTRL_UNIPHIER.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix up Sören's name in the Zynq driver. I caused this. I fix it.

Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Supplying pinmux configuration for e.g. gpio pins leads to deferred
probes because the pinctrl device is probed much later than gpio.
Move the init call to a much earlier stage so it probes before the
devices that may need it.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The description of the XUSB_PADCTL_USB3_PAD_MUX_0 register in the Tegra124
documentation implies that all functions (pcie, usb3 and sata) can be
muxed onto to all lanes (pcie lanes 0-4 and sata lane 0). However, it has
been confirmed that this is not the case and the mux'ing options much more
limited. Unfortunately, the public documentation has not been updated to
reflect this and so detail the actual mux'ing options here by function:

Function:		Lanes:
pcie1 x2:		pcie3, pcie4
pcie1 x4:		pcie1, pcie2, pcie3, pcie4
pcie2 x1 (option1):	pcie0
pcie2 x1 (option2):	pcie2
usb3 port 0:		pcie0
usb3 port 1 (option 1):	pcie1
usb3 port 1 (option 2):	sata0
sata:			sata0

Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This driver adds pinctrl/GPIO support for Intel Broxton. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Reserved for ACPI actually means that in such case the GPIO hardware will
not update the interrupt status register (GPI_IS) even if the pin is
configured to trigger an interrupt. It will update GPI_GPE_STS instead and
does not trigger an interrupt.

Allow using such pins as GPIOs, only prevent their usage as interrupts.

We also rename function intel_pad_reserved_for_acpi() to be
intel_pad_acpi_mode() which reflects the actual meaning better.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>