Pull pinctrl fixes from Linus Walleij:

 - Three fixes to make the boot path for device tree work properly on
   the Nomadik pin controller.

 - Compile warning fix for the vt8500 driver.

 - Fix error path in pinctrl-single.

 - Free mappings in error path of the Lantiq controller.

 - Documentation fixes.

* tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl/lantiq: Free mapping configs for both pin and groups
  pinctrl: single: fix error return code in pcs_parse_one_pinctrl_entry()
  pinctrl: generic: Fix typos and clarify comments
  pinctrl: vt8500: Fix incorrect data in WM8750 pinctrl table
  pinctrl: abx500: Rejiggle platform data and DT initialisation
  pinctrl: abx500: Specify failed sub-driver by ID instead of driver_data

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When creating mappings from DT both pin config and group config mappings
are allocated. Free them both when destroying the mappings.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Introduced by commit 9dddb4df90d136429b6d6ddefceb49a9b93f6cd1
(pinctrl: single: support generic pinconf)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

WMT_PIN_WAKEUP1 should be declared as WMT_PIN(0, 17) rather than
WMT_PIN(0, 16). This currently generates a runtime warning because
WMT_PIN_WAKEUP0 is already defined as WMT_PIN(0, 16).

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Platform Data is invariably populated for this driver, even when
booting with Device Tree. Thus the Device Tree probing code encased
within the first check for Platform Data will never executed, causing
the driver to fail when DT is enabled.

This patch fixes the aforementioned regression by rejigging the
probe() semantics to attempt to extract a platform ID from Device Tree
if one can not be sourced from platform data.

A pointer to GPIO platform data is always passed to the driver now, so
there's little point in checking for 'pdata' and executing the DT case if
it's not there. The difference between booting with DT and !DT is when
booting with DT, plat_id is not populated. Thus, in the DT case we have
to use a DT match table in order to find out which platform we're
executing on. So, we're changing the semantics here to only use the
match table if no plat_id is supplied though platform data.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
[edited commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If a sub-driver has not been specified correctly, there is a good chance
that plat_id is NULL, hence using an attribute of plat_id in the error
message is likely to not only fail the driver but Oops the kernel. Use
the failed ID instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull removal of GENERIC_GPIO from Grant Likely:
 "GENERIC_GPIO now synonymous with GPIOLIB.  There are no longer any
  valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
  is possible to do so which has been causing confusion and breakage.
  This branch does the work to completely eliminate GENERIC_GPIO."

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
  gpio: update gpio Chinese documentation
  Remove GENERIC_GPIO config option
  Convert selectors of GENERIC_GPIO to GPIOLIB
  blackfin: force use of gpiolib
  m68k: coldfire: use gpiolib
  mips: pnx833x: remove requirement for GENERIC_GPIO
  openrisc: default GENERIC_GPIO to false
  avr32: default GENERIC_GPIO to false
  xtensa: remove explicit selection of GENERIC_GPIO
  sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
  powerpc: remove redundant GENERIC_GPIO selection
  unicore32: default GENERIC_GPIO to false
  unicore32: remove unneeded select GENERIC_GPIO
  arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
  arm: remove redundant GENERIC_GPIO selection
  mips: alchemy: require gpiolib
  mips: txx9: change GENERIC_GPIO to GPIOLIB
  mips: loongson: use GPIO driver on CONFIG_GPIOLIB
  mips: remove redundant GENERIC_GPIO select

Pull ARM SoC platform updates (part 3) from Arnd Bergmann:
 "This is the third and smallest of the SoC specific updates.  Changes
  include:

   - SMP support for the Xilinx zynq platform
   - Smaller imx changes
   - LPAE support for mvebu
   - Moving the orion5x, kirkwood, dove and mvebu platforms to a common
     "mbus" driver for their internal devices.

  It would be good to get feedback on the location of the "mbus" driver.
  Since this is used on multiple platforms may potentially get shared
  with other architectures (powerpc and arm64), it was moved to
  drivers/bus/.  We expect other similar drivers to get moved to the
  same place in order to avoid creating more top-level directories under
  drivers/ or cluttering up the messy drivers/misc/ even more."

* tag 'soc-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
  ARM: imx: reset_controller may be disabled
  ARM: mvebu: Align the internal registers virtual base to support LPAE
  ARM: mvebu: Limit the DMA zone when LPAE is selected
  arm: plat-orion: remove addr-map code
  arm: mach-mv78xx0: convert to use the mvebu-mbus driver
  arm: mach-orion5x: convert to use mvebu-mbus driver
  arm: mach-dove: convert to use mvebu-mbus driver
  arm: mach-kirkwood: convert to use mvebu-mbus driver
  arm: mach-mvebu: convert to use mvebu-mbus driver
  ARM i.MX53: set CLK_SET_RATE_PARENT flag on the tve_ext_sel clock
  ARM i.MX53: tve_di clock is not part of the CCM, but of TVE
  ARM i.MX53: make tve_ext_sel propagate rate change to PLL
  ARM i.MX53: Remove unused tve_gate clkdev entry
  ARM i.MX5: Remove tve_sel clock from i.MX53 clock tree
  ARM: i.MX5: Add PATA and SRTC clocks
  ARM: imx: do not bring up unavailable cores
  ARM: imx: add initial imx6dl support
  ARM: imx1: mm: add call to mxc_device_init
  ARM: imx_v4_v5_defconfig: Add CONFIG_GPIO_SYSFS
  ARM: imx_v6_v7_defconfig: Select CONFIG_PERF_EVENTS
  ...

Pull ARM SoC platform updates (part 2) from Arnd Bergmann:
 "These patches are all for Renesas shmobile, and depend on the earlier
  pinctrl updates.  Remarkably, this adds support for three new SoCs:
  r8a73a4, r8a73a4 and r8a7778.  The bulk of the code added for these is
  for pinctrl (using the new subsystem) and for clocks (not yet using
  the common clock subsystem).  The latter will have to get converted in
  one of the upcoming releases, but shmobile is not ready for that yet.

  The series also contains Renesas shmobile board changes, adding one
  board file for each of the three new SoCs.  These boards are using a
  mix of classic and device-tree based probing, as there is still a lot
  of infrastructure in shmobile that has not been converted to DT yet.
  Once those are resolved to the degree that no board specific setup
  code is needed, they can get folded into the respective SoC setup files."

* tag 'soc-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
  ARM: shmobile: use r8a7790 timer setup code on Lager
  ARM: shmobile: force enable of r8a7790 arch timer
  ARM: shmobile: Add second I/O range for r8a7790 PFC
  ARM: shmobile: bockw: enable network settings on bootargs
  ARM: shmobile: bockw: add SMSC ethernet support
  ARM: shmobile: R8A7778: add Ether support
  ARM: shmobile: bockw: enable SMSC ethernet on defconfig
  ARM: shmobile: r8a7778: add r8a7778_init_irq_extpin()
  ARM: shmobile: r8a7778: remove pointless PLATFORM_INFO()
  ARM: shmobile: mackerel: clean up MMCIF vs. SDHI1 selection
  ARM: shmobile: mackerel: add interrupt names for SDHI0
  ARM: shmobile: mackerel: switch SDHI and MMCIF interfaces to slot-gpio
  ARM: shmobile: mackerel: remove OCR masks, where regulators are used
  ARM: shmobile: mackerel: SDHI resources do not have to be numbered
  ARM: shmobile: Initial r8a7790 Lager board support
  ARM: shmobile: APE6EVM LAN9220 support
  ARM: shmobile: APE6EVM PFC support
  ARM: shmobile: APE6EVM base support
  ARM: shmobile: kzm9g-reference: add ethernet support
  ARM: shmobile: add R-Car M1A Bock-W platform support
  ...