The regs pointer in amd_gpio_irq_handler() should have __iomem
on it, so add that to fix the following sparse warnings:

drivers/pinctrl/pinctrl-amd.c:555:14: warning: incorrect type in assignment (different address spaces)
drivers/pinctrl/pinctrl-amd.c:555:14:    expected unsigned int [usertype] *regs
drivers/pinctrl/pinctrl-amd.c:555:14:    got void [noderef] <asn:2> *base
drivers/pinctrl/pinctrl-amd.c:563:34: warning: incorrect type in argument 1 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:563:34:    expected void const volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:563:34:    got unsigned int [usertype] *
drivers/pinctrl/pinctrl-amd.c:580:34: warning: incorrect type in argument 1 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:580:34:    expected void const volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:580:34:    got unsigned int [usertype] *
drivers/pinctrl/pinctrl-amd.c:587:25: warning: incorrect type in argument 2 (different address spaces)
drivers/pinctrl/pinctrl-amd.c:587:25:    expected void volatile [noderef] <asn:2> *addr
drivers/pinctrl/pinctrl-amd.c:587:25:    got unsigned int [usertype] *

Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20191022151154.5986-1-ben.dooks@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When cold-booting Asus X434DA, GPIO 7 is found to be already configured
as an interrupt, and the GPIO level is found to be in a state that
causes the interrupt to fire.

As soon as pinctrl-amd probes, this interrupt fires and invokes
amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was
invoked, so the GPIO level being unchanged just causes another interrupt
to fire again immediately after.

This results in an interrupt storm causing this platform to hang
during boot, right after pinctrl-amd is probed.

Detect this situation and disable the GPIO interrupt when this happens.
This enables the affected platform to boot as normal. GPIO 7 actually is
the I2C touchpad interrupt line, and later on, i2c-multitouch loads and
re-enables this interrupt when it is ready to handle it.

Instead of this approach, I considered disabling all GPIO interrupts at
probe time, however that seems a little risky, and I also confirmed that
Windows does not seem to have this behaviour: the same 41 GPIO IRQs are
enabled under both Linux and Windows, which is a far larger collection
than the GPIOs referenced by the DSDT on this platform.

Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms and conditions of the gnu general public license
  version 2 as published by the free software foundation

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 101 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the AMD reference boards used single GPIO line for
multiple devices. So added IRQF_SHARED flag in amd pinctrl driver.

Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix spelling mistake: "lenght" -> "length"

Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is the 4.19-rc6 release

I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

From the AMD BKDG, if WAKE_INT_MASTER_REG.MaskStsEn is set, a software
write to the debounce registers of *any* gpio will block wake/interrupt
status generation for *all* gpios for a length of time that depends on
WAKE_INT_MASTER_REG.MaskStsLength[11:0].  During this period the Interrupt
Delivery bit (INTERRUPT_ENABLE) will read as 0.

In commit 4c1de0414a1340 ("pinctrl/amd: poll InterruptEnable bits in
enable_irq") we tried to fix this same "gpio Interrupts are blocked
immediately after writing debounce registers" problem, but incorrectly
assumed it only affected the gpio whose debounce was being configured
and not ALL gpios.

To solve this for all gpios, we move the polling loop from
amd_gpio_irq_enable() to amd_gpio_irq_set_type(), while holding the gpio
spinlock.  This ensures that another gpio operation (e.g.
amd_gpio_irq_unmask()) can read a temporarily disabled IRQ and
incorrectly disable it while trying to modify some other register bits.

Fixes: 4c1de0414a1340 pinctrl/amd: poll InterruptEnable bits in enable_irq
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.

Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.

Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>