linux.git/drivers/pinctrl/Kconfig, branch v4.2 Linux kernel source tree pinctrl: sirf: add sirf atlas7 pinctrl and gpio support 2015-05-19T14:01:30+00:00 Wei Chen Wei.Chen@csr.com 2015-05-18T07:28:32+00:00 f9367793293d2262460942b0a4904c21857a1a8b The Pinctrl module (ioc) controls the Pad's function select (each pad can have 8 functions), Pad's Drive Strength, Pad's Pull Select and Pad's Input Disable status. The ioc has two modules, ioc_top & ioc_rtc. Both of these two modules have function select/clear, Pull select and Drive Strength registers. But only ioc_rtc has input-disable registers. The Pads on ioc_top have to access ioc_rtc to set their input-disable status and intpu-disable-value. So have to use one ioc driver instance to drive these two ioc modules at the same time, and each ioc module will be treat as one bank on the "IOC Device". The GPIO Controller controls the GPIO status if the Pad has been config as GPIO by Pinctrl already. Includes the GPIO Input/output, Interrupt type, Interrupt Status, and Set/Get Values. The GPIO pull up/down are controlled by Pinctrl. There are 7 GPIO Groups and splited into 3 MACROs in atlas7. The GPIO Groups in one MACRO share one GPIO controllers, each GPIO Group are treated as one GPIO bank. For example: In VDIFM macro, there is one GPIO Controller, it has 3 banks to control 3 gpio groups. Its gpio name space is from 0 to 95. The Device Tree can be written as following: gpio-ranges = <&pinctrl 0 0 0>, <&pinctrl 32 0 0>, <&pinctrl 64 0 0>; gpio-ranges-group-names = "gnss_gpio_grp", "lcd_vip_gpio_grp", "sdio_i2s_gpio_grp"; bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp". bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp". bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp". Signed-off-by: Wei Chen <Wei.Chen@csr.com> Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.

The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.

So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".

The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.

There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.

For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.

The Device Tree can be written as following:

gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;

gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";

bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".

Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: Add Pistachio SoC pin control driver 2015-05-12T11:19:41+00:00 Andrew Bresticker abrestic@chromium.org 2015-05-06T19:59:03+00:00 cefc03e5995e82082b1e4cda4ef565ccdaff1f45 Add a driver for the pin controller present on the IMG Pistachio SoC. This driver provides pinmux and pinconfig operations as well as GPIO and IRQ chips for the GPIO banks. Changes from v4: - Switched to using gpiochip_add_pin_range(). - Fixed up Kconfig entry. Changes from v3: - Addressed review comments from Ezequiel. Changes from v2: - Removed module stuff which would be compiled out. Changes from v1: - Addressed review comments from Linus. - Changed compatible string to "img,pistachio-system-pinctrl". - Look for GPIO sub-nodes by name. - A couple of bug fixes. Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com> Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com> Signed-off-by: Kevin Cernekee <cernekee@chromium.org> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Cc: James Hartley <james.hartley@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.

Changes from v4:
 - Switched to using gpiochip_add_pin_range().
 - Fixed up Kconfig entry.
Changes from v3:
 - Addressed review comments from Ezequiel.
Changes from v2:
 - Removed module stuff which would be compiled out.
Changes from v1:
 - Addressed review comments from Linus.
 - Changed compatible string to "img,pistachio-system-pinctrl".
 - Look for GPIO sub-nodes by name.
 - A couple of bug fixes.

Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: add lpc18xx pinctrl driver 2015-05-06T12:45:18+00:00 Joachim Eastwood manabian@gmail.com 2015-04-27T22:14:08+00:00 2f77ac93a947f19301a18250845e4be776c71afd Pinctrl driver for the System Control Unit (SCU) found on NXP LPC18xx/43xx devices. Driver uses the generic pinctrl DT bindings for multiplexing and property settings. Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.

Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: fix allmodconfig noise 2015-04-15T08:02:42+00:00 Linus Walleij linus.walleij@linaro.org 2015-04-15T08:00:35+00:00 b99e6fb86541e4dc28f5c3ff7418347fa9d8d29c There was some mess in the dependencies in the pinctrl Kconfig for compile tests under allmodconfig. Mea Culpa. Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
There was some mess in the dependencies in the pinctrl
Kconfig for compile tests under allmodconfig. Mea Culpa.

Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: add AMD GPIO driver support. 2015-03-18T01:02:21+00:00 Ken Xue Ken.Xue@amd.com 2015-03-10T07:02:19+00:00 dbad75dd1f25e0107c643d42774a7f9a8ba85e9b KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM. Current driver patch only support GPIO in x86. Signed-off-by: Ken Xue <Ken.Xue@amd.com> [Moved back to <linux/gpio.h> header] Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.

Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: mediatek: Add Pinctrl/GPIO driver for mt8135. 2015-03-18T01:02:14+00:00 Hongzhou Yang hongzhou.yang@mediatek.com 2015-01-21T05:28:15+00:00 a6df410d420aa4ff316797d352f69e7ebae5ff98 The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs. The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control. This driver include common driver and mt8135 part. The common driver include the pinctrl driver and GPIO driver. The mt8135 part contain its special device data. Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.

The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.

This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.

Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: bcm: consolidate Broadcom pinctrl drivers 2015-03-18T01:02:12+00:00 Ray Jui rjui@broadcom.com 2015-03-05T00:35:49+00:00 b17f2f9b86f4d44b1d90abf5f1d8de423a74c772 Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/* Signed-off-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Consolidate Broadcom pinctrl drivers into drivers/pinctrl/bcm/*

Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: tegra: add a driver for Tegra210 2015-03-09T17:10:59+00:00 Stephen Warren swarren@nvidia.com 2015-02-24T21:00:51+00:00 9184f756908ace8213099f21870b07491a7138a9 Tegra210's pinmux supports a different set of pins/options than earlier SoCs, so requires its own driver (well, table of pin-specific data). Cc: devicetree@vger.kernel.org Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).

Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: add driver for Amlogic Meson SoCs 2015-01-26T08:13:00+00:00 Beniamino Galvani b.galvani@gmail.com 2015-01-17T18:15:14+00:00 6ac730951104a437bf828683bcf9ba66336c4fa7 This is a driver for the pinmux and GPIO controller available in Amlogic Meson SoCs. It currently supports only Meson8, however the common code should be generic enough to work also for other SoCs after having defined the proper set of functions and groups. GPIO interrupts are not supported at the moment due to lack of documentation. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.

GPIO interrupts are not supported at the moment due to lack of
documentation.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: sirf: drop marco support 2015-01-14T13:21:54+00:00 Barry Song Baohua.Song@csr.com 2015-01-11T13:56:41+00:00 a17272a46ce1133d1b2232d6584d947565b720ee marco chip has been dropped, clear its support. Signed-off-by: Barry Song <Baohua.Song@csr.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
marco chip has been dropped, clear its support.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>