Pull pci updates from Bjorn Helgaas:
 "Resource management:

   - Distribute spare resources to unconfigured hotplug bridges at
     boot-time (not just when hot-adding such a bridge), which makes
     hot-adding devices to docks work better.

   - Revert to a BAR assignment inherited from firmware only when the
     address is actually reachable via any upstream bridges, which fixes
     some cases where firmware doesn't configure all devices.

   - Add a sysfs interface to resize BARs so this can be done before
     assigning devices to a VM through VFIO.

  Power management:

   - Disable Precision Time Management for all devices on suspend to
     enable lower-power PM state. We previously did this just for Root
     Ports, which isn't enough because downstream devices can still
     generate PTM messages, which cause errors if it's disabled in the
     Root Port.

   - Save and restore the ASPM L1 PM Substates configuration for
     suspend/ resume. Previously this configuration was lost, so L1.x
     states likely stopped working after resume.

   - Check whether the L1 PM Substates Capability exists. If it didn't
     exist, we previously read junk and tried to configure L1 Substates
     based on that.

   - Fix the LTR_L1.2_THRESHOLD computation, which previously set a
     threshold for entering L1.2 that was too low in some cases.

   - Reduce the delay after transitions to or from D3cold by using
     usleep_range() rather than msleep(), which often slept for ~19ms
     instead of the 10ms normally required. The spec says 10ms is
     enough, but it's possible we could trip over devices that need a
     little more.

  Error handling:

   - Work around a BIOS bug that caused Intel Root Ports to advertise a
     Root Port Programmed I/O (RP PIO) log size of zero, which caused
     annoying warnings and prevented the kernel from dumping log
     registers for DPC errors.

  Qualcomm PCIe controller driver:

   - Add support for SC8280XP and SA8540P host controllers and SM8450
     endpoint controller.

   - Disable Master AXI clock on endpoint controllers to save power when
     link is idle or in L1.x.

   - Expose link state transition counts via debugfs to help debug
     issues with low-power states.

   - Add auto-loading module support.

  Synopsys DesignWare PCIe controller driver:

   - Remove a dependency on ZONE_DMA32 by allocating the MSI target page
     differently. There's more work to do related to eDMA controllers,
     so it's not completely settled"

* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
  PCI: qcom-ep: Check platform_get_resource_byname() return value
  PCI: qcom-ep: Add support for SM8450 SoC
  dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
  dt-bindings: PCI: qcom-ep: Define clocks per platform
  PCI: qcom-ep: Make PERST separation optional
  dt-bindings: PCI: qcom-ep: Make PERST separation optional
  PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
  PCI: Expose PCIe Resizable BAR support via sysfs
  PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
  PCI/ASPM: Ignore L1 PM Substates if device lacks capability
  PCI/ASPM: Factor out L1 PM Substates configuration
  PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
  PCI: qcom-ep: Expose link transition counts via debugfs
  PCI: qcom-ep: Disable IRQs during driver remove
  PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
  PCI/ASPM: Refactor L1 PM Substates Control Register programming
  PCI: qcom-ep: Make use of the cached dev pointer
  PCI: qcom-ep: Rely on the clocks supplied by devicetree
  PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
  phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
  ...

Pull USB / Thunderbolt updates from Greg KH:
 "Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.

  Nothing major in here, lots of little things with new devices
  supported and updates for a few drivers. Highlights include:

   - thunderbolt/USB4 devices supported a bit better than before, and
     some new ids to enable new hardware devices

   - USB gadget uvc updates for newer video formats and better v4l
     integration (the v4l portions were acked by those maintainers)

   - typec updates for tiny issues and more typec drivers for new chips.

   - xhci tiny updates for minor issues

   - big usb-serial ftdi_sio driver update to handle new devices better

   - lots of tiny dwc3 fixes and updates for the IP block that is
     showing up everywhere these days

   - dts updates for new devices being supported

   - other tiny janitorial and cleanups fixes for lots of different USB
     drivers. Full details are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
  usb: gadget: uvc: don't put item still in use
  usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
  usb: host: ehci-exynos: switch to using gpiod API
  Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
  Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
  dt-bindings: usb: Convert FOTG210 to dt schema
  usb: mtu3: fix failed runtime suspend in host only mode
  USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
  usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
  usb: typec: Replace custom implementation of device_match_fwnode()
  usb: typec: ucsi: Don't warn on probe deferral
  usb: add quirks for Lenovo OneLink+ Dock
  MAINTAINERS: switch dwc3 to Thinh
  usb: idmouse: fix an uninit-value in idmouse_open
  USB: PHY: JZ4770: Switch to use dev_err_probe() helper
  usb: phy: generic: Switch to use dev_err_probe() helper
  usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
  usb: cdns3: remove dead code
  usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
  usb: musb: sunxi: Switch to use dev_err_probe() helper
  ...

Pull phy updates from Vinod Koul:
 "This contains bunch of new device support and one new Sunplus driver
  along with updates which include another big round of qmp phy
  conversion.

  New support:
   - Qualcomm SC8280XP eDP & DP and USB3 UNI phy (Bjorn Andersson)
   - Rockchip rk3568 inno dsidphy (Chris Morgan)
   - ocelot-serdes phy yaml binding (Colin Foster)
   - Renesas gen2-usb phy yaml binding (Geert Uytterhoeven)
   - RGMII suport in lan966x driver (Horatiu Vultur)
   - Qualcomm SM6375 usb snps-femto-v2 bindings (Konrad Dybcio)
   - Rockchip rk356x csi-dphya (Michael Riesch)
   - Qualcomm sdm670 usb2 bindings (Richard Acayan)
   - Sunplus USB2 PHY (Vincent Shih)

  Updates:
   - Mediatek hdmi, ufs, tphy and xsphy updates to use bitfield helpers
     (Chunfeng Yun)
   - Continued Qualcomm qmp phy driver split and cleanup. More patches
     are under review and expected that next cycle might see completion
     of this activity (Dmitry Baryshkov & Johan Hovold)
   - TI wiz driver support for j7200 10g (Roger Quadros)
   - Qualcomm femto phy driver support for override params to help with
     tuning (Sandeep Maheswaram)
   - SGMII support in TI wiz driver (Siddharth Vadapalli)
   - dev_err_probe simplification (Yuan Can)"

* tag 'phy-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (170 commits)
  phy: phy-mtk-dp: make array driving_params static const
  dt-bindings: phy: qcom,qusb2: document sdm670 compatible
  phy: qcom-qmp-pcie: fix resource mapping for SDM845 QHP PHY
  phy: rockchip-snps-pcie3: only look for rockchip,pipe-grf on rk3588
  phy: tegra: xusb: Enable usb role switch attribute
  phy: mediatek: fix build warning of FIELD_PREP()
  phy: qcom-qmp-usb: Use dev_err_probe() to simplify code
  phy: qcom-qmp-ufs: Use dev_err_probe() to simplify code
  phy: qcom-qmp-pcie-msm8996: Use dev_err_probe() to simplify code
  phy: qcom-qmp-combo: Use dev_err_probe() to simplify code
  phy: qualcomm: call clk_disable_unprepare in the error handling
  phy: intel: Use dev_err_probe() to simplify code
  phy: tegra: xusb: Use dev_err_probe() to simplify code
  phy: qcom-snps: Use dev_err_probe() to simplify code
  phy: qcom-qusb2: Use dev_err_probe() to simplify code
  phy: qcom-qmp-pcie: Use dev_err_probe() to simplify code
  phy: ti: phy-j721e-wiz: fix reference leaks in wiz_probe()
  phy: mediatek: mipi: remove register access helpers
  phy: mediatek: mipi: mt8183: use common helper to access registers
  phy: mediatek: mipi: mt8183: use GENMASK to generate bits mask
  ...

Pull ARM driver updates from Arnd Bergmann:
 "The drivers branch for 6.1 is a bit larger than for most releases.

  Most of the changes come from SoC maintainers for the drivers/soc
  subsystem:

   - A new driver for error handling on the NVIDIA Tegra 'control
     backbone' bus.

   - A new driver for Qualcomm LLCC/DDR bandwidth measurement

   - New Rockchip rv1126 and rk3588 power domain drivers

   - DT binding updates for memory controllers, older Rockchip SoCs,
     various Mediatek devices, Qualcomm SCM firmware

   - Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
     Apple rtkit firmware driver, Tegra firmware

   - Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
     Qualcomm, Broadcom, NXP, ...)

  There are also some separate subsystem with downstream maintainers
  that merge updates this way:

   - Various updates and new drivers in the memory controller subsystem
     for Mediatek and Broadcom SoCs

   - Small set of changes in preparation to add support for FF-A v1.1
     specification later, in the Arm FF-A firmware subsystem

   - debugfs support in the PSCI firmware subsystem"

* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
  ARM: remove check for CONFIG_DEBUG_LL_SER3
  firmware/psci: Add debugfs support to ease debugging
  firmware/psci: Print a warning if PSCI doesn't accept PC mode
  dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
  dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
  dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
  dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
  soc: sunxi: sram: Add support for the D1 system control
  soc: sunxi: sram: Export the LDO control register
  soc: sunxi: sram: Save a pointer to the OF match data
  soc: sunxi: sram: Return void from the release function
  soc: apple: rtkit: Add apple_rtkit_poll
  soc: imx: add i.MX93 media blk ctrl driver
  soc: imx: add i.MX93 SRC power domain driver
  soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
  soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
  soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
  soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
  soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
  soc: imx: add icc paths for i.MX8MP media blk ctrl
  ...

Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.

Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b002258 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>

No conflicts.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Don't populate the read-only array driving_params on the stack but instead
make it static const. Also makes the object code a little smaller.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220929130147.97375-1-colin.i.king@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

On SDM845 one of PCIe PHYs (the QHP one) has the same region for TX and
RX registers. Since the commit 4be26f695ffa ("phy: qcom-qmp-pcie: fix
memleak on probe deferral") added checking that resources are not
allocated beforehand, this PHY can not be probed anymore. Fix this by
skipping the map of ->rx resource on the QHP PHY and assign it manually.

Fixes: 4be26f695ffa ("phy: qcom-qmp-pcie: fix memleak on probe deferral")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220926172514.880776-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The rockchip,pipe-grf property is only used on rk3588, but not on
rk3568. Therefore this property is not present on rk3568 devices,
leading to the following message:

  rockchip-snps-pcie3-phy fe8c0000.phy: failed to find rockchip,pipe_grf regmap

Fix that by only looking for this property on rk3588.

Fixes: 2e9bffc4f713d ("phy: rockchip: Support PCIe v3")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://lore.kernel.org/r/20220927051752.53089-1-aurelien@aurel32.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>

This patch enables the usb-role-switch attribute and lets users check
the current device role of the otg capability ports

Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20220928125640.2219402-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>