linux.git/drivers/phy, branch v4.16

phy: qcom-ufs: add MODULE_LICENSE tag

2018-03-12T09:41:59+00:00

While the specific UFS PHY drivers (14nm and 20nm) have a module
license, the common base module does not, leading to a Kbuild
failure:

WARNING: modpost: missing MODULE_LICENSE() in drivers/phy/qualcomm/phy-qcom-ufs.o
FATAL: modpost: GPL-incompatible module phy-qcom-ufs.ko uses GPL-only symbol 'clk_enable'

This adds a module description and license tag to fix the build.
I added both Yaniv and Vivek as authors here, as Yaniv sent the initial
submission, while Vivek did most of the work since.

Signed-off-by: Arnd Bergmann 
Acked-by: Bjorn Andersson 
Signed-off-by: Kishon Vijay Abraham I

Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

2018-02-01T17:40:49+00:00

Pull USB/PHY updates from Greg KH:
 "Here is the big USB and PHY driver update for 4.16-rc1.

  Along with the normally expected XHCI, MUSB, and Gadget driver
  patches, there are some PHY driver fixes, license cleanups, sysfs
  attribute cleanups, usbip changes, and a raft of other smaller fixes
  and additions.

  Full details are in the shortlog.

  All of these have been in the linux-next tree for a long time with no
  reported issues"

* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
  USB: serial: pl2303: new device id for Chilitag
  USB: misc: fix up some remaining DEVICE_ATTR() usages
  USB: musb: fix up one odd DEVICE_ATTR() usage
  USB: atm: fix up some remaining DEVICE_ATTR() usage
  USB: move many drivers to use DEVICE_ATTR_WO
  USB: move many drivers to use DEVICE_ATTR_RO
  USB: move many drivers to use DEVICE_ATTR_RW
  USB: misc: chaoskey: Use true and false for boolean values
  USB: storage: remove old wording about how to submit a change
  USB: storage: remove invalid URL from drivers
  usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
  usbip: list: don't list devices attached to vhci_hcd
  usbip: prevent bind loops on devices attached to vhci_hcd
  USB: serial: remove redundant initializations of 'mos_parport'
  usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
  usb: gadget: compress return logic into one line
  usbip: vhci_hcd: update 'status' file header and format
  USB: serial: simple: add Motorola Tetra driver
  CDC-ACM: apply quirk for card reader
  usb: option: Add support for FS040U modem
  ...

Merge branch 'for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2018-01-30T22:48:30+00:00

Pull libata updates from Tejun Heo:
 "Nothing too interesting. Several patches to convert mdelay() to
  usleep_range(), removal of unused pata_at32, and other low level
  driver specific changes"

* 'for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ata: pata_pdc2027x: Replace mdelay with msleep
  ata: pata_it821x: Replace mdelay with usleep_range in it821x_firmware_command
  ata: sata_mv: Replace mdelay with usleep_range in mv_reset_channel
  ata: remove pata_at32
  phy: brcm-sata: remove unused variable
  phy: brcm-sata: fix semicolon.cocci warnings
  ata: ahci_brcm: Recover from failures to identify devices
  phy: brcm-sata: Implement calibrate callback
  ahci: Add Intel Cannon Lake PCH-H PCI ID
  ata_piix: constify pci_bits
  libata:pata_atiixp: Don't use unconnected secondary port on SB600
  ata: ahci_brcm: Avoid clobbering SATA_TOP_CTRL_BUS_CTRL
  ahci: Allow setting a default LPM policy for mobile chipsets
  ahci: Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
  ahci: Annotate PCI ids for mobile Intel chipsets as such

phy: work around 'phys' references to usb-nop-xceiv devices

2018-01-19T15:12:37+00:00

Stefan Wahren reports a problem with a warning fix that was merged
for v4.15: we had lots of device nodes with a 'phys' property pointing
to a device node that is not compliant with the binding documented in
Documentation/devicetree/bindings/phy/phy-bindings.txt

This generally works because USB HCD drivers that support both the generic
phy subsystem and the older usb-phy subsystem ignore most errors from
phy_get() and related calls and then use the usb-phy driver instead.

However, it turns out that making the usb-nop-xceiv device compatible with
the generic-phy binding changes the phy_get() return code from -EINVAL to
-EPROBE_DEFER, and the dwc2 usb controller driver for bcm2835 now returns
-EPROBE_DEFER from its probe function rather than ignoring the failure,
breaking all USB support on raspberry-pi when CONFIG_GENERIC_PHY is
enabled. The same code is used in the dwc3 driver and the usb_add_hcd()
function, so a reasonable assumption would be that many other platforms
are affected as well.

I have reviewed all the related patches and concluded that "usb-nop-xceiv"
is the only USB phy that is affected by the change, and since it is by far
the most commonly referenced phy, all the other USB phy drivers appear
to be used in ways that are are either safe in DT (they don't use the
'phys' property), or in the driver (they already ignore -EPROBE_DEFER
from generic-phy when usb-phy is available).

To work around the problem, this adds a special case to _of_phy_get()
so we ignore any PHY node that is compatible with "usb-nop-xceiv",
as we know that this can never load no matter how much we defer. In the
future, we might implement a generic-phy driver for "usb-nop-xceiv"
and then remove this workaround.

Since we generally want older kernels to also want to work with the
fixed devicetree files, it would be good to backport the patch into
stable kernels as well (3.13+ are possibly affected), even though they
don't contain any of the patches that may have caused regressions.

Fixes: 014d6da6cb25 ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Fixes: c5bbf358b790 arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
Fixes: 44e5dced2ef6 arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
Fixes: f568f6f554b8 ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
Fixes: d745d5f277bf ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
Fixes: 915fbe59cbf2 ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
Link: https://marc.info/?l=linux-usb&m=151518314314753&w=2
Link: https://patchwork.kernel.org/patch/10158145/
Cc: stable@vger.kernel.org
Cc: Felipe Balbi 
Cc: Eric Anholt 
Tested-by: Stefan Wahren 
Acked-by: Rob Herring 
Tested-by: Hans Verkuil 
Acked-by: Kishon Vijay Abraham I 
Signed-off-by: Arnd Bergmann

phy: brcm-sata: remove unused variable

2018-01-18T14:45:57+00:00

The newly introduced calibrate function has a variable
that has never been used and needs to be removed to avoid
this harmless warning:

drivers/phy/broadcom/phy-brcm-sata.c: In function 'brcm_stb_sata_calibrate':
drivers/phy/broadcom/phy-brcm-sata.c:514:24: error: unused variable 'priv' [-Werror=unused-variable]

Fixes: 3e507769d15e ("phy: brcm-sata: Implement calibrate callback")
Signed-off-by: Arnd Bergmann 
Signed-off-by: Tejun Heo

phy: brcm-sata: fix semicolon.cocci warnings

2018-01-17T20:10:13+00:00

drivers/phy/broadcom/phy-brcm-sata.c:534:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Fixes: 3e507769d15e ("phy: brcm-sata: Implement calibrate callback")
CC: Florian Fainelli 
Signed-off-by: Fengguang Wu 
Signed-off-by: Tejun Heo

phy: brcm-sata: Implement calibrate callback

2018-01-17T15:52:29+00:00

Implement the calibration callback to allow turning on the Clock-Data
Recovery module clamping when necessary, e.g: during failure to identify
a SATA hard drive from ahci_brcm.c::brcm_ahci_read_id.

Signed-off-by: Florian Fainelli 
Acked-by: Kishon Vijay Abraham I 
Signed-off-by: Tejun Heo

Merge tag 'phy-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

2018-01-08T13:17:59+00:00

Kishon writes:

phy: for 4.16

 *) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
 *) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
 *) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
    to save power
 *) Fix in Broadcom USB PHY to prevent abort in DRD mode
 *) Fix in Broadcom USB PHY to use the correct dt properties
 *) Fix in Mediatek PHY to detect device connection
 *) Make getting resource optional for Mediatek V1 TPHY
 *) Cleanup in Mediatek PHY

Signed-off-by: Kishon Vijay Abraham I

phy: phy-mtk-tphy: use of_device_get_match_data()

2017-12-29T07:30:35+00:00

reduce the boilerplate code to get the specific data

Signed-off-by: Chunfeng Yun 
Signed-off-by: Kishon Vijay Abraham I

phy: phy-mtk-tphy: make shared banks optional for V1 TPHY

2017-12-29T07:30:35+00:00

V1 TPHY for SATA doesn't have shared banks if it isn't shared
with PCIe or USB, so make it optional.

Signed-off-by: Chunfeng Yun 
Signed-off-by: Kishon Vijay Abraham I