Pull Hyper-V fixes from Wei Liu:

 - Two fixes for Hyper-V PCI driver (Long Li, Sahil Chandna)

 - Fix an infinite loop issue in MSHV driver (Stanislav Kinsburskii)

* tag 'hyperv-fixes-signed-20260406' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  mshv: Fix infinite fault loop on permission-denied GPA intercepts
  PCI: hv: Fix double ida_free in hv_pci_probe error path
  PCI: hv: Set default NUMA node to 0 for devices without affinity info

If hv_pci_probe() fails after storing the domain number in
hbus->bridge->domain_nr, there is a call to free this domain_nr via
pci_bus_release_emul_domain_nr(), however, during cleanup, the bridge
release callback pci_release_host_bridge_dev() also frees the domain_nr
causing ida_free to be called on same ID twice and triggering following
warning:

  ida_free called for id=28971 which is not allocated.
  WARNING: lib/idr.c:594 at ida_free+0xdf/0x160, CPU#0: kworker/0:2/198
  Call Trace:
   pci_bus_release_emul_domain_nr+0x17/0x20
   pci_release_host_bridge_dev+0x4b/0x60
   device_release+0x3b/0xa0
   kobject_put+0x8e/0x220
   devm_pci_alloc_host_bridge_release+0xe/0x20
   devres_release_all+0x9a/0xd0
   device_unbind_cleanup+0x12/0xa0
   really_probe+0x1c5/0x3f0
   vmbus_add_channel_work+0x135/0x1a0

Fix this by letting pci core handle the free domain_nr and remove
the explicit free called in pci-hyperv driver.

Fixes: bcce8c74f1ce ("PCI: Enable host bridge emulation for PCI_DOMAINS_GENERIC platforms")
Signed-off-by: Sahil Chandna <sahilchandna@linux.microsoft.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>

When hv_pci_assign_numa_node() processes a device that does not have
HV_PCI_DEVICE_FLAG_NUMA_AFFINITY set or has an out-of-range
virtual_numa_node, the device NUMA node is left unset. On x86_64,
the uninitialized default happens to be 0, but on ARM64 it is
NUMA_NO_NODE (-1).

Tests show that when no NUMA information is available from the Hyper-V
host, devices perform best when assigned to node 0. With NUMA_NO_NODE
the kernel may spread work across NUMA nodes, which degrades
performance on Hyper-V, particularly for high-throughput devices like
MANA.

Always set the device NUMA node to 0 before the conditional NUMA
affinity check, so that devices get a performant default when the host
provides no NUMA information, and behavior is consistent on both
x86_64 and ARM64.

Fixes: 999dd956d838 ("PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>

The for_each_endpoint_of_node() macro requires calling of_node_put() on the
endpoint node when breaking out of the loop early.

Add of_node_put(endpoint) before the early return to release the reference.

Fixes: cf3287fb2c1f ("PCI/pwrctrl: Ensure that remote endpoint node parent has supply requirement")
Signed-off-by: Felix Gu <ustc.gu@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260323-pwctrl-v1-1-f5c03a2df7fb@gmail.com

With the move to explicit pwrctrl power on/off APIs, the caller, i.e., the
PCI controller driver, should manage the power state. The pwrctrl drivers
should not try to clean up or power off when they are removed, as this
might end up disabling an already disabled regulator, causing a big
warning.  This can be triggered if a PCI controller driver's .remove()
callback calls pci_pwrctrl_destroy_devices() after
pci_pwrctrl_power_off_devices().

Drop the devm cleanup parts that turn off regulators from the pwrctrl
drivers.

Fixes: b921aa3f8dec ("PCI/pwrctrl: Switch to pwrctrl create, power on/off, destroy APIs")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260226092234.3859740-1-wenst@chromium.org

Pull pci fixes from Bjorn Helgaas:

 - Create pwrctrl devices only for DT nodes below a PCI controller that
   describe PCI devices and are related to a power supply; this prevents
   waiting indefinitely for pwrctrl drivers that will never probe
   (Manivannan Sadhasivam)

 - Restore endpoint BAR mapping on subrange setup failure to make
   selftest reliable (Koichiro Den)

* tag 'pci-v7.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
  PCI: endpoint: pci-epf-test: Roll back BAR mapping when subrange setup fails
  PCI/pwrctrl: Create pwrctrl devices only for PCI device nodes
  PCI/pwrctrl: Ensure that remote endpoint node parent has supply requirement

When the BAR subrange mapping test on DWC-based platforms fails due to
insufficient free inbound iATU regions, pci_epf_test_bar_subrange_setup()
returns an error (-ENOSPC) but does not restore the original BAR mapping.
This causes subsequent test runs to become confusing, since the failure may
leave room for the next subrange mapping test to pass.

Fix this by restoring the original BAR mapping when preparation of the
subrange mapping fails, so that no side effect remains regardless of the
test success or failure.

Fixes: 6c5e6101423b ("PCI: endpoint: pci-epf-test: Add BAR subrange mapping test support")
Reported-by: Christian Bruel <christian.bruel@foss.st.com>
Closes: https://lore.kernel.org/linux-pci/b2b03ebe-9482-4a13-b22f-7b44da096eed@foss.st.com/
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Christian Bruel <christian.bruel@foss.st.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260316140225.1481658-1-den@valinux.co.jp

A PCI host bridge node can have non-PCI child nodes (OPP tables, USB
hub, etc.) as well as PCI device child nodes.

Ensure that pwrctrl devices are only created for PCI device nodes by
checking for the 'pci' prefix in the compatible property.

Fixes: 4c4132489201 ("PCI/pwrctrl: Add APIs to create, destroy pwrctrl devices")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/all/20260212-rb3gen2-upd-gl3590-v1-1-18fb04bb32b0@oss.qualcomm.com
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260223-pwrctrl-fixes-7-0-v2-2-97566dfb1809@oss.qualcomm.com

If OF graph is used in the PCI device node, the pwrctrl core creates a
pwrctrl device even if the remote endpoint doesn't have power supply
requirements. Since the device doesn't have any power supply requirements,
there was no pwrctrl driver to probe, leading to PCI controller driver
probe deferral as it waits for all pwrctrl drivers to probe before starting
bus scan.

This issue happens with Qcom ath12k devices with WSI interface attached to
the Qcom IPQ platforms.

Fix this issue by checking for the existence of at least one power supply
property in the remote endpoint parent node. To consolidate all the checks,
create a new helper pci_pwrctrl_is_required() and move all the checks
there.

Fixes: 9db826206f9b ("PCI/pwrctrl: Create pwrctrl device if graph port is found")
Reported-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Raj Kumar Bhagat <raj.bhagat@oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260223-pwrctrl-fixes-7-0-v2-1-97566dfb1809@oss.qualcomm.com

Pull xen fixes from Juergen Gross:

 - a cleanup of arch/x86/kernel/head_64.S removing the pre-built page
   tables for Xen guests

 - a small comment update

 - another cleanup for Xen PVH guests mode

 - fix an issue with Xen PV-devices backed by driver domains

* tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/xenbus: better handle backend crash
  xenbus: add xenbus_device parameter to xenbus_read_driver_state()
  x86/PVH: Use boot params to pass RSDP address in start_info page
  x86/xen: update outdated comment
  xen/acpi-processor: fix _CST detection using undersized evaluation buffer
  x86/xen: Build identity mapping page tables dynamically for XENPV