Pull PCI fix from Bjorn Helgaas:
 "If an IOMMU is present, ignore the P2PDMA whitelist we added for v5.2
  because we don't yet know how to support P2PDMA in that case (Logan
  Gunthorpe)"

* tag 'pci-v5.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/P2PDMA: Ignore root complex whitelist when an IOMMU is present

Presently, there is no path to DMA map P2PDMA memory, so if a TLP targeting
this memory hits the root complex and an IOMMU is present, the IOMMU will
reject the transaction, even if the RC would support P2PDMA.

So until the kernel knows to map these DMA addresses in the IOMMU, we
should not enable the whitelist when an IOMMU is present.

Link: https://lore.kernel.org/linux-pci/20190522201252.2997-1-logang@deltatee.com/
Fixes: 0f97da831026 ("PCI/P2PDMA: Allow P2P DMA between any devices under AMD ZEN Root Complex")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>

Pull power management fix from Rafael Wysocki:
 "Prevent PCI bridges in general (and PCIe ports in particular) from
  being put into low-power states during system-wide suspend transitions
  if there are any devices in D0 below them and refine the handling of
  PCI devices in D0 during suspend-to-idle cycles"

* tag 'pm-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PCI: PM: Skip devices in D0 for suspend-to-idle

Logan noticed that devm_memremap_pages_release() kills the percpu_ref
drops all the page references that were acquired at init and then
immediately proceeds to unplug, arch_remove_memory(), the backing pages
for the pagemap.  If for some reason device shutdown actually collides
with a busy / elevated-ref-count page then arch_remove_memory() should
be deferred until after that reference is dropped.

As it stands the "wait for last page ref drop" happens *after*
devm_memremap_pages_release() returns, which is obviously too late and
can lead to crashes.

Fix this situation by assigning the responsibility to wait for the
percpu_ref to go idle to devm_memremap_pages() with a new ->cleanup()
callback.  Implement the new cleanup callback for all
devm_memremap_pages() users: pmem, devdax, hmm, and p2pdma.

Link: http://lkml.kernel.org/r/155727339156.292046.5432007428235387859.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: 41e94a851304 ("add devm_memremap_pages")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In preparation for fixing a race between devm_memremap_pages_release()
and the final put of a page from the device-page-map, allocate a
percpu-ref per p2pdma resource mapping.

Link: http://lkml.kernel.org/r/155727338646.292046.9922678317501435597.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The pci_p2pdma_add_resource() implementation immediately frees the pgmap
if gen_pool_add_virt() fails.  However, that means that when @dev
triggers a devres release devm_memremap_pages_release() will crash
trying to access the freed @pgmap.

Use the new devm_memunmap_pages() to manually free the mapping in the
error path.

Link: http://lkml.kernel.org/r/155727337603.292046.13101332703665246702.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixes: 52916982af48 ("PCI/P2PDMA: Support peer-to-peer memory")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Jérôme Glisse" <jglisse@redhat.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
attempted to avoid a problem with devices whose drivers want them to
stay in D0 over suspend-to-idle and resume, but it did not go as far
as it should with that.

Namely, first of all, the power state of a PCI bridge with a
downstream device in D0 must be D0 (based on the PCI PM spec r1.2,
sec 6, table 6-1, if the bridge is not in D0, there can be no PCI
transactions on its secondary bus), but that is not actively enforced
during system-wide PM transitions, so use the skip_bus_pm flag
introduced by commit d491f2b75237 for that.

Second, the configuration of devices left in D0 (whatever the reason)
during suspend-to-idle need not be changed and attempting to put them
into D0 again by force is pointless, so explicitly avoid doing that.

Fixes: d491f2b75237 ("PCI: PM: Avoid possible suspend-to-idle issue")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>

If a PCI driver leaves the device handled by it in D0 and calls
pci_save_state() on the device in its ->suspend() or ->suspend_late()
callback, it can expect the device to stay in D0 over the whole
s2idle cycle.  However, that may not be the case if there is a
spurious wakeup while the system is suspended, because in that case
pci_pm_suspend_noirq() will run again after pci_pm_resume_noirq()
which calls pci_restore_state(), via pci_pm_default_resume_early(),
so state_saved is cleared and the second iteration of
pci_pm_suspend_noirq() will invoke pci_prepare_to_sleep() which
may change the power state of the device.

To avoid that, add a new internal flag, skip_bus_pm, that will be set
by pci_pm_suspend_noirq() when it runs for the first time during the
given system suspend-resume cycle if the state of the device has
been saved already and the device is still in D0.  Setting that flag
will cause the next iterations of pci_pm_suspend_noirq() to set
state_saved for pci_pm_resume_noirq(), so that it always restores the
device state from the originally saved data, and avoid calling
pci_prepare_to_sleep() for the device.

Fixes: 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Both acpi_pci_need_resume() and acpi_dev_needs_resume() check if the
current ACPI wakeup configuration of the device matches what is
expected as far as system wakeup from sleep states is concerned, as
reflected by the device_may_wakeup() return value for the device.

However, they only should do that if wakeup.flags.valid is set for
the device's ACPI companion, because otherwise the wakeup.prepare_count
value for it is meaningless.

Add the missing wakeup.flags.valid checks to these functions.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Pull PCI updates from Bjorn Helgaas:
 "Enumeration changes:

   - Add _HPX Type 3 settings support, which gives firmware more
     influence over device configuration (Alexandru Gagniuc)

   - Support fixed bus numbers from bridge Enhanced Allocation
     capabilities (Subbaraya Sundeep)

   - Add "external-facing" DT property to identify cases where we
     require IOMMU protection against untrusted devices (Jean-Philippe
     Brucker)

   - Enable PCIe services for host controller drivers that use managed
     host bridge alloc (Jean-Philippe Brucker)

   - Log PCIe port service messages with pci_dev, not the pcie_device
     (Frederick Lawler)

   - Convert pciehp from pciehp_debug module parameter to generic
     dynamic debug (Frederick Lawler)

  Peer-to-peer DMA:

   - Add whitelist of Root Complexes that support peer-to-peer DMA
     between Root Ports (Christian König)

  Native controller drivers:

   - Add PCI host bridge DMA ranges for bridges that can't DMA
     everywhere, e.g., iProc (Srinath Mannam)

   - Add Amazon Annapurna Labs PCIe host controller driver (Jonathan
     Chocron)

   - Fix Tegra MSI target allocation so DMA doesn't generate unwanted
     MSIs (Vidya Sagar)

   - Fix of_node reference leaks (Wen Yang)

   - Fix Hyper-V module unload & device removal issues (Dexuan Cui)

   - Cleanup R-Car driver (Marek Vasut)

   - Cleanup Keystone driver (Kishon Vijay Abraham I)

   - Cleanup i.MX6 driver (Andrey Smirnov)

  Significant bug fixes:

   - Reset Lenovo ThinkPad P50 GPU so nouveau works after reboot (Lyude
     Paul)

   - Fix Switchtec firmware update performance issue (Wesley Sheng)

   - Work around Pericom switch link retraining erratum (Stefan Mätje)"

* tag 'pci-v5.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (141 commits)
  MAINTAINERS: Add Karthikeyan Mitran and Hou Zhiqiang for Mobiveil PCI
  PCI: pciehp: Remove pointless MY_NAME definition
  PCI: pciehp: Remove pointless PCIE_MODULE_NAME definition
  PCI: pciehp: Remove unused dbg/err/info/warn() wrappers
  PCI: pciehp: Log messages with pci_dev, not pcie_device
  PCI: pciehp: Replace pciehp_debug module param with dyndbg
  PCI: pciehp: Remove pciehp_debug uses
  PCI/AER: Log messages with pci_dev, not pcie_device
  PCI/DPC: Log messages with pci_dev, not pcie_device
  PCI/PME: Replace dev_printk(KERN_DEBUG) with dev_info()
  PCI/AER: Replace dev_printk(KERN_DEBUG) with dev_info()
  PCI: Replace dev_printk(KERN_DEBUG) with dev_info(), etc
  PCI: Replace printk(KERN_INFO) with pr_info(), etc
  PCI: Use dev_printk() when possible
  PCI: Cleanup setup-bus.c comments and whitespace
  PCI: imx6: Allow asynchronous probing
  PCI: dwc: Save root bus for driver remove hooks
  PCI: dwc: Use devm_pci_alloc_host_bridge() to simplify code
  PCI: dwc: Free MSI in dw_pcie_host_init() error path
  PCI: dwc: Free MSI IRQ page in dw_pcie_free_msi()
  ...