linux.git/drivers/pci/hotplug, branch v2.6.13

[PATCH] PCI Hotplug: new contact info

2005-08-17T04:06:24+00:00

Signed-off-by: Kristen Carlson Accardi 
Signed-off-by: Greg Kroah-Hartman 
Signed-off-by: Linus Torvalds

[IA64] hotplug/ia64: SN Hotplug Driver - SN Hotplug Driver code

2005-07-06T22:29:53+00:00

This patch is the SGI hotplug driver and additional changes required for
the driver.  These modifications include changes to the SN io_init.c code
for memory management, the inclusion of new SAL calls to enable and disable
PCI slots, and a hotplug-style driver.

Signed-off-by: Prarit Bhargava 
Signed-off-by: Tony Luck

[PATCH] cpqphp: fix oops during unload without probe

2005-06-28T04:52:46+00:00

drivers/pci/hotplug/cpqphp_core.c calls cpqphp_event_start_thread()
in one_time_init(), which is called whenever the hardware is probed.
Unfortunately, cpqphp_event_stop_thread() is *always* called when
the module is unloaded. If the hardware is never probed, then
cpqphp_event_stop_thread() tries to manipulate a couple of
uninitialized mutexes.

Signed-off-by: Keith Moore 
Signed-off-by: Greg Kroah-Hartman

[PATCH] ACPI based I/O APIC hot-plug: acpiphp support

2005-06-28T04:52:45+00:00

This patch adds PCI based I/O xAPIC hot-add support to ACPIPHP
driver. When PCI root bridge is hot-added, all PCI based I/O xAPICs
under the root bridge are hot-added by this patch. Hot-remove support
is TBD.

Signed-off-by: Kenji Kaneshige 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] acpi hotplug: decouple slot power state changes from physical hotplug

2005-06-28T04:52:43+00:00

Current acpiphp code does not distinguish between the physical presence and
power state of a device/slot.  That is, if a device has to be disabled, it
also tries to physically ejects the device.  This patch decouples power state
from physical presence.  You can now echo to the corresponding sysfs power
control file to repeatedly enable and disable a device without having to
physically re-insert it.

Signed-off-by: Rajesh Shah 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] acpi hotplug: aCPI based root bridge hot-add

2005-06-28T04:52:43+00:00

acpiphp changes to support acpi based root bridge hot-add.

Signed-off-by: Rajesh Shah 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] acpi hotplug: fix slot power-down problem with acpiphp

2005-06-28T04:52:43+00:00

Earlier I reported that Matthew's acpiphp rewrite had problem in powering down
slot on my i386 system.  The following patch is needed to get the acpiphp
rewrite properly powering down the slot.

Signed-off-by: Dely Sy 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] acpi hotplug: clean up notify handlers on acpiphp unload

2005-06-28T04:52:42+00:00

A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it.  In this case, we need
to clean up the p2p bridges and slots properly too.  Patch below applies on
top of the original patch, and fixes this problem.  Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too.  Patch was tested on an ia64 Tiger4 box.

Signed-off-by: Rajesh Shah 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] acpi hotplug: convert acpiphp to use generic resource code

2005-06-28T04:52:42+00:00

This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files.  It's tested on an hp Integrity rx8620 (which won't work without this
patch).  Testers with other hardware welcomed.

Signed-off-by: Matthew Wilcox 
Signed-off-by: Andrew Morton 
Signed-off-by: Greg Kroah-Hartman

[PATCH] Driver Core: drivers/i2c/chips/w83781d.c - drivers/s390/block/dcssblk.c: update device attribute callbacks

2005-06-20T22:15:34+00:00

Signed-off-by: Yani Ioannou 
Signed-off-by: Greg Kroah-Hartman