linux.git/drivers/pci/controller/dwc, branch v6.4-rc2 Linux kernel source tree Merge tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci 2023-04-27T17:45:30+00:00 Linus Torvalds torvalds@linux-foundation.org 2023-04-27T17:45:30+00:00 34b62f186db9614e55d021f8c58d22fc44c57911 Pull pci updates from Bjorn Helgaas: "Resource management: - Add pci_dev_for_each_resource() and pci_bus_for_each_resource() iterators PCIe native device hotplug: - Fix AB-BA deadlock between reset_lock and device_lock Power management: - Wait longer for devices to become ready after resume (as we do for reset) to accommodate Intel Titan Ridge xHCI devices - Extend D3hot delay for NVIDIA HDA controllers to avoid unrecoverable devices after a bus reset Error handling: - Clear PCIe Device Status after EDR since generic error recovery now only clears it when AER is native ASPM: - Work around Chromebook firmware defect that clobbers Capability list (including ASPM L1 PM Substates Cap) when returning from D3cold to D0 Freescale i.MX6 PCIe controller driver: - Install imprecise external abort handler only when DT indicates PCIe support Freescale Layerscape PCIe controller driver: - Add ls1028a endpoint mode support Qualcomm PCIe controller driver: - Add SM8550 DT binding and driver support - Add SDX55 DT binding and driver support - Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 - Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 - Add DT "mhi" register region for supported SoCs - Expose link transition counts via debugfs to help debug low power issues - Support system suspend and resume; reduce interconnect bandwidth and turn off clock and PHY if there are no active devices - Enable async probe by default to reduce boot time Miscellaneous: - Sort controller Kconfig entries by vendor" * tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (56 commits) PCI: xilinx: Drop obsolete dependency on COMPILE_TEST PCI: mobiveil: Sort Kconfig entries by vendor PCI: dwc: Sort Kconfig entries by vendor PCI: Sort controller Kconfig entries by vendor PCI: Use consistent controller Kconfig menu entry language PCI: xilinx-nwl: Add 'Xilinx' to Kconfig prompt PCI: hv: Add 'Microsoft' to Kconfig prompt PCI: meson: Add 'Amlogic' to Kconfig prompt PCI: Use of_property_present() for testing DT property presence PCI/PM: Extend D3hot delay for NVIDIA HDA controllers dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties PCI: qcom: Add SM8550 PCIe support dt-bindings: PCI: qcom: Add SM8550 compatible PCI: qcom: Add support for SDX55 SoC dt-bindings: PCI: qcom-ep: Fix the unit address used in example dt-bindings: PCI: qcom: Add SDX55 SoC dt-bindings: PCI: qcom: Update maintainers entry PCI: qcom: Enable async probe by default PCI: qcom: Add support for system suspend and resume PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter ... 
Pull pci updates from Bjorn Helgaas:
 "Resource management:

   - Add pci_dev_for_each_resource() and pci_bus_for_each_resource()
     iterators

  PCIe native device hotplug:

   - Fix AB-BA deadlock between reset_lock and device_lock

  Power management:

   - Wait longer for devices to become ready after resume (as we do for
     reset) to accommodate Intel Titan Ridge xHCI devices

   - Extend D3hot delay for NVIDIA HDA controllers to avoid
     unrecoverable devices after a bus reset

  Error handling:

   - Clear PCIe Device Status after EDR since generic error recovery now
     only clears it when AER is native

  ASPM:

   - Work around Chromebook firmware defect that clobbers Capability
     list (including ASPM L1 PM Substates Cap) when returning from
     D3cold to D0

  Freescale i.MX6 PCIe controller driver:

   - Install imprecise external abort handler only when DT indicates
     PCIe support

  Freescale Layerscape PCIe controller driver:

   - Add ls1028a endpoint mode support

  Qualcomm PCIe controller driver:

   - Add SM8550 DT binding and driver support

   - Add SDX55 DT binding and driver support

   - Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3

   - Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0

   - Add DT "mhi" register region for supported SoCs

   - Expose link transition counts via debugfs to help debug low power
     issues

   - Support system suspend and resume; reduce interconnect bandwidth
     and turn off clock and PHY if there are no active devices

   - Enable async probe by default to reduce boot time

  Miscellaneous:

   - Sort controller Kconfig entries by vendor"

* tag 'pci-v6.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (56 commits)
  PCI: xilinx: Drop obsolete dependency on COMPILE_TEST
  PCI: mobiveil: Sort Kconfig entries by vendor
  PCI: dwc: Sort Kconfig entries by vendor
  PCI: Sort controller Kconfig entries by vendor
  PCI: Use consistent controller Kconfig menu entry language
  PCI: xilinx-nwl: Add 'Xilinx' to Kconfig prompt
  PCI: hv: Add 'Microsoft' to Kconfig prompt
  PCI: meson: Add 'Amlogic' to Kconfig prompt
  PCI: Use of_property_present() for testing DT property presence
  PCI/PM: Extend D3hot delay for NVIDIA HDA controllers
  dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
  PCI: qcom: Add SM8550 PCIe support
  dt-bindings: PCI: qcom: Add SM8550 compatible
  PCI: qcom: Add support for SDX55 SoC
  dt-bindings: PCI: qcom-ep: Fix the unit address used in example
  dt-bindings: PCI: qcom: Add SDX55 SoC
  dt-bindings: PCI: qcom: Update maintainers entry
  PCI: qcom: Enable async probe by default
  PCI: qcom: Add support for system suspend and resume
  PCI/PM: Drop pci_bridge_wait_for_secondary_bus() timeout parameter
  ...
PCI: dwc: Sort Kconfig entries by vendor 2023-04-20T21:18:05+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-18T17:43:35+00:00 c39819c044be495abe6a6041f4a49cc58340e2a7 Sort Kconfig entries by vendor so they appear in alphabetical order in menuconfig. Link: https://lore.kernel.org/r/20230418174336.145585-7-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> 
Sort Kconfig entries by vendor so they appear in alphabetical order in
menuconfig.

Link: https://lore.kernel.org/r/20230418174336.145585-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI: Use consistent controller Kconfig menu entry language 2023-04-20T21:18:04+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-18T17:43:33+00:00 80c170d7b13d0a46a46f869774baf3c02d775654 Use "PCIe controller" consistently instead of "host bridge", "bus driver", etc. Annotate with "(host mode)" or "(endpoint mode)" as needed. Link: https://lore.kernel.org/r/20230418174336.145585-5-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> 
Use "PCIe controller" consistently instead of "host bridge", "bus driver",
etc.  Annotate with "(host mode)" or "(endpoint mode)" as needed.

Link: https://lore.kernel.org/r/20230418174336.145585-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI: meson: Add 'Amlogic' to Kconfig prompt 2023-04-20T21:18:04+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-18T17:43:30+00:00 6ba4ce6b2ef6fe4be102cefeb89b3979af130983 Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to match other PCIe drivers. Capitalize "Meson" to match other Meson Kconfig prompts. Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Yue Wang <yue.wang@Amlogic.com> 
Add the "Amlogic" vendor name to the CONFIG_PCI_MESON Kconfig prompt to
match other PCIe drivers.  Capitalize "Meson" to match other Meson Kconfig
prompts.

Link: https://lore.kernel.org/r/20230418174336.145585-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Merge branch 'pci/controller/qcom' 2023-04-20T21:16:38+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-20T21:16:38+00:00 5c5dd8839fc02fa9b9558005a32ce4d7d86fd774 - Use correct PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register for v2.7.0 (Manivannan Sadhasivam) - Remove "PCIE20_" prefix from register definitions (Manivannan Sadhasivam) - Sort registers and bitfield declarations (Manivannan Sadhasivam) - Convert to GENMASK and FIELD_PREP (Manivannan Sadhasivam) - Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 (Manivannan Sadhasivam) - Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 (Manivannan Sadhasivam) - Rename qcom_pcie_config_sid_sm8250() to be non SM8250-specific (Manivannan Sadhasivam) - Add DT "mhi" register region for supported SoCs (Manivannan Sadhasivam) - Expose link transition counts via debugfs to help debug low power issues (Manivannan Sadhasivam) - Support system suspend and resume; reduce interconnect bandwidth and turn off clock and PHY if there are no active devices (Manivannan Sadhasivam) - Enable async probe by default to reduce boot time (Manivannan Sadhasivam) - Add Manivannan Sadhasivam as qcom DT binding maintainer, replacing Stanimir Varbanov (Manivannan Sadhasivam) - Add DT binding and driver support for Qcom SDX55 SoC (Manivannan Sadhasivam) - Add DT binding and driver support for SM8550 SoC (Abel Vesa) - Document msi-map and msi-map-mask DT properties (Manivannan Sadhasivam) * pci/controller/qcom: dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties PCI: qcom: Add SM8550 PCIe support dt-bindings: PCI: qcom: Add SM8550 compatible PCI: qcom: Add support for SDX55 SoC dt-bindings: PCI: qcom-ep: Fix the unit address used in example dt-bindings: PCI: qcom: Add SDX55 SoC dt-bindings: PCI: qcom: Update maintainers entry PCI: qcom: Enable async probe by default PCI: qcom: Add support for system suspend and resume PCI: qcom: Expose link transition counts via debugfs dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version PCI: qcom: Use macros for defining total no. of clocks & supplies PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0 PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3 PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3 PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2 PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0 PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0 PCI: qcom: Use lower case for hex PCI: qcom: Add missing macros for register fields PCI: qcom: Use bitfield definitions for register fields PCI: qcom: Sort and group registers and bitfield definitions PCI: qcom: Remove PCIE20_ prefix from register definitions PCI: qcom: Fix the incorrect register usage in v2.7.0 config 
- Use correct PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register for v2.7.0
  (Manivannan Sadhasivam)

- Remove "PCIE20_" prefix from register definitions (Manivannan Sadhasivam)

- Sort registers and bitfield declarations (Manivannan Sadhasivam)

- Convert to GENMASK and FIELD_PREP (Manivannan Sadhasivam)

- Use bulk APIs for clocks of IP 1.0.0, 2.3.2, 2.3.3 (Manivannan
  Sadhasivam)

- Use bulk APIs for reset of IP 2.1.0, 2.3.3, 2.4.0 (Manivannan Sadhasivam)

- Rename qcom_pcie_config_sid_sm8250() to be non SM8250-specific
  (Manivannan Sadhasivam)

- Add DT "mhi" register region for supported SoCs (Manivannan Sadhasivam)

- Expose link transition counts via debugfs to help debug low power issues
  (Manivannan Sadhasivam)

- Support system suspend and resume; reduce interconnect bandwidth and turn
  off clock and PHY if there are no active devices (Manivannan Sadhasivam)

- Enable async probe by default to reduce boot time (Manivannan Sadhasivam)

- Add Manivannan Sadhasivam as qcom DT binding maintainer, replacing
  Stanimir Varbanov (Manivannan Sadhasivam)

- Add DT binding and driver support for Qcom SDX55 SoC (Manivannan
  Sadhasivam)

- Add DT binding and driver support for SM8550 SoC (Abel Vesa)

- Document msi-map and msi-map-mask DT properties (Manivannan Sadhasivam)

* pci/controller/qcom:
  dt-bindings: PCI: qcom: Document msi-map and msi-map-mask properties
  PCI: qcom: Add SM8550 PCIe support
  dt-bindings: PCI: qcom: Add SM8550 compatible
  PCI: qcom: Add support for SDX55 SoC
  dt-bindings: PCI: qcom-ep: Fix the unit address used in example
  dt-bindings: PCI: qcom: Add SDX55 SoC
  dt-bindings: PCI: qcom: Update maintainers entry
  PCI: qcom: Enable async probe by default
  PCI: qcom: Add support for system suspend and resume
  PCI: qcom: Expose link transition counts via debugfs
  dt-bindings: PCI: qcom: Add "mhi" register region to supported SoCs
  PCI: qcom: Rename qcom_pcie_config_sid_sm8250() to reflect IP version
  PCI: qcom: Use macros for defining total no. of clocks & supplies
  PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
  PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.3.3
  PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.3
  PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 2.3.2
  PCI: qcom: Use bulk clock APIs for handling clocks for IP rev 1.0.0
  PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.1.0
  PCI: qcom: Use lower case for hex
  PCI: qcom: Add missing macros for register fields
  PCI: qcom: Use bitfield definitions for register fields
  PCI: qcom: Sort and group registers and bitfield definitions
  PCI: qcom: Remove PCIE20_ prefix from register definitions
  PCI: qcom: Fix the incorrect register usage in v2.7.0 config
Merge branch 'pci/controller/layerscape' 2023-04-20T21:16:37+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-20T21:16:37+00:00 d7493f273b4ab70a3fb72161bf6762b8df63c33d - Add ls1028a endpoint mode support (Xiaowei Bao) * pci/controller/layerscape: PCI: layerscape: Add EP mode support for ls1028a 
- Add ls1028a endpoint mode support (Xiaowei Bao)

* pci/controller/layerscape:
  PCI: layerscape: Add EP mode support for ls1028a
Merge branch 'pci/controller/kirin' 2023-04-20T21:16:36+00:00 Bjorn Helgaas bhelgaas@google.com 2023-04-20T21:16:36+00:00 2ad2e01914fdee7f4ccda0a837e3ab62bddd0d4d - Select CONFIG_REGMAP_MMIO so kirin driver links correctly (Josh Triplett) * pci/controller/kirin: PCI: kirin: Select REGMAP_MMIO 
- Select CONFIG_REGMAP_MMIO so kirin driver links correctly (Josh Triplett)

* pci/controller/kirin:
  PCI: kirin: Select REGMAP_MMIO
PCI: qcom: Add SM8550 PCIe support 2023-04-12T13:22:31+00:00 Abel Vesa abel.vesa@linaro.org 2023-03-20T14:46:58+00:00 6276a403c0ff2908a05d1ff4f80f961478baebbd SM8550 requires two additional clocks for proper working. Add these two clocks as optional clocks (as only required by this platform) and compatible for this platform. While at it, let's also rename the reset variable to "rst" from "pci_reset" to match the existing naming preference. Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org Signed-off-by: Abel Vesa <abel.vesa@linaro.org> [lpieralisi@kernel.org: commit log rewording] Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> 
SM8550 requires two additional clocks for proper working.

Add these two clocks as optional clocks (as only required by this
platform) and compatible for this platform.

While at it, let's also rename the reset variable to "rst" from
"pci_reset" to match the existing naming preference.

Link: https://lore.kernel.org/r/20230320144658.1794991-2-abel.vesa@linaro.org
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
[lpieralisi@kernel.org: commit log rewording]
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
PCI: qcom: Add support for SDX55 SoC 2023-04-12T08:11:03+00:00 Manivannan Sadhasivam manivannan.sadhasivam@linaro.org 2023-03-08T08:24:24+00:00 7394d0a85d6f847946dfe3f114f4d3f6a3988a36 Add support for SDX55 SoC reusing the 1.9.0 config. The PCIe controller is of version 1.10.0 but it is compatible with the 1.9.0 config. This SoC also requires "sleep" clock which is added as an optional clock in the driver, since it is not required on other SoCs. Link: https://lore.kernel.org/r/20230308082424.140224-14-manivannan.sadhasivam@linaro.org Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> 
Add support for SDX55 SoC reusing the 1.9.0 config. The PCIe controller is
of version 1.10.0 but it is compatible with the 1.9.0 config. This SoC also
requires "sleep" clock which is added as an optional clock in the driver,
since it is not required on other SoCs.

Link: https://lore.kernel.org/r/20230308082424.140224-14-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
PCI: qcom: Enable async probe by default 2023-04-12T06:49:04+00:00 Manivannan Sadhasivam manivannan.sadhasivam@linaro.org 2023-03-20T06:46:44+00:00 c0e1eb441b1de42500cbc081b8d754caae6b27b1 Qcom PCIe RC driver waits for the PHY link to be up during the probe; this consumes several milliseconds during boot. Enable async probe by default so that other drivers can load in parallel while this driver waits for the link to be up. Suggested-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20230320064644.5217-1-manivannan.sadhasivam@linaro.org Tested-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> 
Qcom PCIe RC driver waits for the PHY link to be up during the probe;
this consumes several milliseconds during boot.

Enable async probe by default so that other drivers can load in parallel
while this driver waits for the link to be up.

Suggested-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230320064644.5217-1-manivannan.sadhasivam@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>