linux.git/drivers/net, branch v5.4-rc2 Linux kernel source tree net: qlogic: Fix memory leak in ql_alloc_large_buffers 2019-10-05T01:33:13+00:00 Navid Emamdoost navid.emamdoost@gmail.com 2019-10-04T20:24:39+00:00 1acb8f2a7a9f10543868ddd737e37424d5c36cf4 In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb. This skb should be released if pci_dma_mapping_error fails. Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.

Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: at803x: use operating parameters from PHY-specific status 2019-10-05T01:11:08+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-10-04T16:06:14+00:00 06d5f3441b2e80eeb6deb0885aefa00589e463c1 Read the PHY-specific status register for the current operating mode (speed and duplex) of the PHY. This register reflects the actual mode that the PHY has resolved depending on either the advertisements of autoneg is enabled, or the forced mode if autoneg is disabled. This ensures that phylib's software state always tracks the hardware state. It seems both AR8033 (which uses the AR8031 ID) and AR8035 support this status register. AR8030 is not known at the present time. This patch depends on "net: phy: extract pause mode" and "net: phy: extract link partner advertisement reading". Reported-by: tinywrkb <tinywrkb@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: tinywrkb <tinywrkb@gmail.com> Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> 
Read the PHY-specific status register for the current operating mode
(speed and duplex) of the PHY.  This register reflects the actual
mode that the PHY has resolved depending on either the advertisements
of autoneg is enabled, or the forced mode if autoneg is disabled.

This ensures that phylib's software state always tracks the hardware
state.

It seems both AR8033 (which uses the AR8031 ID) and AR8035 support
this status register.  AR8030 is not known at the present time.

This patch depends on "net: phy: extract pause mode" and "net: phy:
extract link partner advertisement reading".

Reported-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: tinywrkb <tinywrkb@gmail.com>
Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: extract pause mode 2019-10-05T01:11:08+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-10-04T16:06:09+00:00 2d880b8709c013d47472f85a9d42ea1aca3bce47 Extract the update of phylib's software pause mode state from genphy_read_status(), so that we can re-use this functionality with PHYs that have alternative ways to read the negotiation results. Tested-by: tinywrkb <tinywrkb@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> 
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.

Tested-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: extract link partner advertisement reading 2019-10-05T01:11:08+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-10-04T16:06:04+00:00 8d3dc3ac9dd6801c732a72ca6979698c38451b4f Move reading the link partner advertisement out of genphy_read_status() into its own separate function. This will allow re-use of this code by PHY drivers that are able to read the resolved status from the PHY. Tested-by: tinywrkb <tinywrkb@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> 
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function.  This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.

Tested-by: tinywrkb <tinywrkb@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: fix write to mii-ctrl1000 register 2019-10-05T01:11:08+00:00 Russell King rmk+kernel@armlinux.org.uk 2019-10-04T16:05:58+00:00 4cf6c57e61fee954f7b7685de31b80ec26843d27 When userspace writes to the MII_ADVERTISE register, we update phylib's advertising mask and trigger a renegotiation. However, writing to the MII_CTRL1000 register, which contains the gigabit advertisement, does neither. This can lead to phylib's copy of the advertisement becoming de-synced with the values in the PHY register set, which can result in incorrect negotiation resolution. Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> 
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation.  However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither.  This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.

Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: allow for reset line to be tied to a sleepy GPIO controller 2019-10-05T01:07:45+00:00 Andrea Merello andrea.merello@gmail.com 2019-10-04T13:53:32+00:00 ea977d19d918324ad5b66953f051a6ed07d0a3c5 mdio_device_reset() makes use of the atomic-pretending API flavor for handling the PHY reset GPIO line. I found no hint that mdio_device_reset() is called from atomic context and indeed it uses usleep_range() since long time, so I would assume that it is OK to sleep there. This patch switch to gpiod_set_value_cansleep() in mdio_device_reset(). This is relevant if e.g. the PHY reset line is tied to a I2C GPIO controller. This has been tested on a ZynqMP board running an upstream 4.19 kernel and then hand-ported on current kernel tree. Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> 
mdio_device_reset() makes use of the atomic-pretending API flavor for
handling the PHY reset GPIO line.

I found no hint that mdio_device_reset() is called from atomic context
and indeed it uses usleep_range() since long time, so I would assume that
it is OK to sleep there.

This patch switch to gpiod_set_value_cansleep() in mdio_device_reset().
This is relevant if e.g. the PHY reset line is tied to a I2C GPIO
controller.

This has been tested on a ZynqMP board running an upstream 4.19 kernel and
then hand-ported on current kernel tree.

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152: Set macpassthru in reset_resume callback 2019-10-05T00:26:03+00:00 Kai-Heng Feng kai.heng.feng@canonical.com 2019-10-04T12:51:04+00:00 a54cdeeb04fc719e4c7f19d6e28dba7ea86cee5b r8152 may fail to establish network connection after resume from system suspend. If the USB port connects to r8152 lost its power during system suspend, the MAC address was written before is lost. The reason is that The MAC address doesn't get written again in its reset_resume callback. So let's set MAC address again in reset_resume callback. Also remove unnecessary lock as no other locking attempt will happen during reset_resume. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
r8152 may fail to establish network connection after resume from system
suspend.

If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.

So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4:Fix out-of-bounds MSI-X info array access 2019-10-04T21:42:13+00:00 Vishal Kulkarni vishal@chelsio.com 2019-10-03T22:36:15+00:00 6b517374f4ea5a3c6e307e1219ec5f35d42e6d00 When fetching free MSI-X vectors for ULDs, check for the error code before accessing MSI-X info array. Otherwise, an out-of-bounds access is attempted, which results in kernel panic. Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD") Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.

Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qmi_wwan: add support for Cinterion CLS8 devices 2019-10-04T20:55:47+00:00 Reinhard Speyerer rspmn@arcor.de 2019-10-03T16:34:39+00:00 cf74ac6db25d4002089e85cc623ad149ecc25614 Add support for Cinterion CLS8 devices. Use QMI_QUIRK_SET_DTR as required for Qualcomm MDM9x07 chipsets. T: Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e2d ProdID=00b0 Rev= 3.18 S: Manufacturer=GEMALTO S: Product=USB Modem C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> 
Add support for Cinterion CLS8 devices.
Use QMI_QUIRK_SET_DTR as required for Qualcomm MDM9x07 chipsets.

T:  Bus=01 Lev=03 Prnt=05 Port=01 Cnt=02 Dev#= 25 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e2d ProdID=00b0 Rev= 3.18
S:  Manufacturer=GEMALTO
S:  Product=USB Modem
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: Avoid deadlock on suspend/resume 2019-10-03T00:21:26+00:00 Thierry Reding treding@nvidia.com 2019-10-02T14:49:46+00:00 134cc4cefad34d8d24670d8a911b59c3b89c6731 The stmmac driver will try to acquire its private mutex during suspend via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init(). However, the phylink configuration is updated with the private mutex held already, which causes a deadlock during suspend. Fix this by moving the phylink configuration updates out of the region of code protected by the private mutex. Fixes: 19e13cb27b99 ("net: stmmac: Hold rtnl lock in suspend/resume callbacks") Suggested-by: Bitan Biswas <bbiswas@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> 
The stmmac driver will try to acquire its private mutex during suspend
via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init().
However, the phylink configuration is updated with the private mutex
held already, which causes a deadlock during suspend.

Fix this by moving the phylink configuration updates out of the region
of code protected by the private mutex.

Fixes: 19e13cb27b99 ("net: stmmac: Hold rtnl lock in suspend/resume callbacks")
Suggested-by: Bitan Biswas <bbiswas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>