The old dmascc driver depends on the legacy ISA_DMA_API, and blindly
just casts the kernel virtual address to 'int' for set_dma_addr().

That works only incidentally, and because the high bits of the address
will be ignored anyway. And on 64-bit architectures it causes warnings.

Admittedly, 64-bit architectures with ISA are basically dead - I think
the only example of this is alpha, and nobody would ever use the dmascc
driver there.  But hey, the fix is easy enough, the end result is
cleaner, and it's yet another configuration that now builds without
warnings.

If somebody actually uses this driver on an alpha and this fixes it for
you, please email me.  Because that is just incredibly bizarre.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf.

  Current release - regressions:

   - vhost_net: fix OoB on sendmsg() failure

   - mlx5: bridge, fix uninitialized variable usage

   - bnxt_en: fix error recovery regression

  Current release - new code bugs:

   - bpf, mm: fix lockdep warning triggered by stack_map_get_build_id_offset()

  Previous releases - regressions:

   - r6040: restore MDIO clock frequency after MAC reset

   - tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()

   - dsa: flush switchdev workqueue before tearing down CPU/DSA ports

  Previous releases - always broken:

   - ptp: dp83640: don't define PAGE0, avoid compiler warning

   - igc: fix tunnel segmentation offloads

   - phylink: update SFP selected interface on advertising changes

   - stmmac: fix system hang caused by eee_ctrl_timer during suspend/resume

   - mlx5e: fix mutual exclusion between CQE compression and HW TS

  Misc:

   - bpf, cgroups: fix cgroup v2 fallback on v1/v2 mixed mode

   - sfc: fallback for lack of xdp tx queues

   - hns3: add option to turn off page pool feature"

* tag 'net-5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (67 commits)
  mlxbf_gige: clear valid_polarity upon open
  igc: fix tunnel offloading
  net/{mlx5|nfp|bnxt}: Remove unnecessary RTNL lock assert
  net: wan: wanxl: define CROSS_COMPILE_M68K
  selftests: nci: replace unsigned int with int
  net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports
  Revert "net: phy: Uniform PHY driver access"
  net: dsa: destroy the phylink instance on any error in dsa_slave_phy_setup
  ptp: dp83640: don't define PAGE0
  bnx2x: Fix enabling network interfaces without VFs
  Revert "Revert "ipv4: fix memory leaks in ip_cmsg_send() callers""
  tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()
  net-caif: avoid user-triggerable WARN_ON(1)
  bpf, selftests: Add test case for mixed cgroup v1/v2
  bpf, selftests: Add cgroup v1 net_cls classid helpers
  bpf, cgroups: Fix cgroup v2 fallback on v1/v2 mixed mode
  bpf: Add oversize check before call kvcalloc()
  net: hns3: fix the timing issue of VF clearing interrupt sources
  net: hns3: fix the exception when query imp info
  net: hns3: disable mac in flr process
  ...

tx timeout and slot time are currently specified in units of HZ.  On
Alpha, HZ is defined as 1024.  When building alpha:allmodconfig, this
results in the following error message.

  drivers/net/hamradio/6pack.c: In function 'sixpack_open':
  drivers/net/hamradio/6pack.c:71:41: error:
  	unsigned conversion from 'int' to 'unsigned char'
  	changes value from '256' to '0'

In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:

    https://www.linux-ax25.org/wiki/6PACK

Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.

Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:

        mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);

and the SIXP_TXDELAY walue is sent as a byte over the wire.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it.  And I think the 'Jensen' actually
did have an ISA slot.

However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':

        outl((int) (skb->data), ioaddr + Wn7_MasterAddr);

which is all kinds of broken.  Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits.  I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".

Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).

Who knows, this might even work.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets.  This problem state
will happen if three specific conditions occur:
    1) driver has received more than (N * RxRingSize) packets but
       less than (N+1 * RxRingSize) packets, where N is an odd number
       Note: the command "ethtool -g <interface>" will display the
       current receive ring size, which currently defaults to 128
    2) the driver's interface was disabled via "ifconfig oob_net0 down"
       during the window described in #1.
    3) the driver's interface is re-enabled via "ifconfig oob_net0 up"

This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware.  Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.

Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking tunnel offloading, it turns out that offloading doesn't work
as expected.  The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'

=== SNIP ===
if [ $# -ne 4 ]
then
  echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
  exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
		   remote "${REMOTE_ADDRESS}" \
		   local "${LOCAL_ADDRESS}" \
		   dstport 0 \
		   dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===

The expected outcome is

  Max. Paket Size: 64904

This is what you see on igb, the code igc has been taken from.
However, on igc the output is

  Max. Paket Size: 1516

so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame.  Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.

It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe.  In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.

Setting the same flags as igb fixes the issue on igc.

Fixes: 34428dff3679 ("igc: Add GSO partial support")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.

This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.

The warnings started after the following patch was merged:
commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")

Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was used but never set.  The hardcoded value from before the dawn of
time was non-standard; the usual name for cross-tools is $TRIPLET-$TOOL

Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.

That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.

The stack trace is:

Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
 mdio_bus_phy_suspend+0xd8/0xec
 dpm_run_callback+0x38/0x90
 __device_suspend+0x108/0x3cc
 dpm_suspend+0x140/0x210
 dpm_suspend_start+0x7c/0xa0
 suspend_devices_and_enter+0x13c/0x540
 pm_suspend+0x2a4/0x330

Examples why that assumption is not fine:

- There is an MDIO bus with a PHY device that doesn't have a specific
  PHY driver loaded, because mdiobus_register() automatically creates a
  PHY device for it but there is no specific PHY driver in the system.
  Normally under those circumstances, the generic PHY driver will be
  bound lazily to it (at phy_attach_direct time). But some Ethernet
  drivers attach to their PHY at .ndo_open time. Until then it, the
  to-be-driven-by-genphy PHY device will not have a driver. The blamed
  patch amounts to saying "you need to open all net devices before the
  system can suspend, to avoid the NULL pointer dereference".

- There is any raw MDIO device which has 'plausible' values in the PHY
  ID registers 2 and 3, which is located on an MDIO bus whose driver
  does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
  devices). An example could be a MAC's internal MDIO bus with PCS
  devices on it, for serial links such as SGMII. PHY devices will get
  created for those PCSes too, due to that MDIO bus auto-scanning, and
  although those PHY devices are not used, they do not bother anybody
  either. PCS devices are usually managed in Linux as raw MDIO devices.
  Nonetheless, they do not have a PHY driver, nor does anybody attempt
  to connect to them (because they are not a PHY), and therefore this
  patch breaks that.

The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.

For instance:

phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.

If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.

That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.

In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.

Fixes: 3ac8eed62596 ("net: phy: Uniform PHY driver access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914140515.2311548-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

gcc 11.x reports the following compiler warning/error.

  drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
  arch/m68k/include/asm/string.h:72:25: error:
	'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]

Use absolute_pointer() to work around the problem.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>