Pull networking fixes from Jakub Kicinski:
 "Networking fixes for 5.13-rc7, including fixes from wireless, bpf,
  bluetooth, netfilter and can.

  Current release - regressions:

   - mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
     to fix modifying offloaded qdiscs

   - lantiq: net: fix duplicated skb in rx descriptor ring

   - rtnetlink: fix regression in bridge VLAN configuration, empty info
     is not an error, bot-generated "fix" was not needed

   - libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix umem
     creation

  Current release - new code bugs:

   - ethtool: fix NULL pointer dereference during module EEPROM dump via
     the new netlink API

   - mlx5e: don't update netdev RQs with PTP-RQ, the special purpose
     queue should not be visible to the stack

   - mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs

   - mlx5e: verify dev is present in get devlink port ndo, avoid a panic

  Previous releases - regressions:

   - neighbour: allow NUD_NOARP entries to be force GCed

   - further fixes for fallout from reorg of WiFi locking (staging:
     rtl8723bs, mac80211, cfg80211)

   - skbuff: fix incorrect msg_zerocopy copy notifications

   - mac80211: fix NULL ptr deref for injected rate info

   - Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs

  Previous releases - always broken:

   - bpf: more speculative execution fixes

   - netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local

   - udp: fix race between close() and udp_abort() resulting in a panic

   - fix out of bounds when parsing TCP options before packets are
     validated (in netfilter: synproxy, tc: sch_cake and mptcp)

   - mptcp: improve operation under memory pressure, add missing
     wake-ups

   - mptcp: fix double-lock/soft lookup in subflow_error_report()

   - bridge: fix races (null pointer deref and UAF) in vlan tunnel
     egress

   - ena: fix DMA mapping function issues in XDP

   - rds: fix memory leak in rds_recvmsg

  Misc:

   - vrf: allow larger MTUs

   - icmp: don't send out ICMP messages with a source address of 0.0.0.0

   - cdc_ncm: switch to eth%d interface naming"

* tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (139 commits)
  net: ethernet: fix potential use-after-free in ec_bhf_remove
  selftests/net: Add icmp.sh for testing ICMP dummy address responses
  icmp: don't send out ICMP messages with a source address of 0.0.0.0
  net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
  net: ll_temac: Fix TX BD buffer overwrite
  net: ll_temac: Add memory-barriers for TX BD access
  net: ll_temac: Make sure to free skb when it is completely used
  MAINTAINERS: add Guvenc as SMC maintainer
  bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
  bnxt_en: Fix TQM fastpath ring backing store computation
  bnxt_en: Rediscover PHY capabilities after firmware reset
  cxgb4: fix wrong shift.
  mac80211: handle various extensible elements correctly
  mac80211: reset profile_periodicity/ema_ap
  cfg80211: avoid double free of PMSR request
  cfg80211: make certificate generation more robust
  mac80211: minstrel_ht: fix sample time check
  net: qed: Fix memcpy() overflow of qed_dcbx_params()
  net: cdc_eem: fix tx fixup skb leak
  net: hamradio: fix memory leak in mkiss_close
  ...

static void ec_bhf_remove(struct pci_dev *dev)
{
...
	struct ec_bhf_priv *priv = netdev_priv(net_dev);

	unregister_netdev(net_dev);
	free_netdev(net_dev);

	pci_iounmap(dev, priv->dma_io);
	pci_iounmap(dev, priv->io);
...
}

priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.

Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.

This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.

Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.

In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.

When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.

Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.

Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.

Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.

Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests.  Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring.  This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.

Fixes: c7dd7ab4b204 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset.  This can cause
some PHY related functionalities to fail after a firmware reset.  For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.

Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While fixing coverity warning, commit dd2c79677375 introduced typo in
shift value. Fix that.

Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Fixes: dd2c79677375 ("cxgb4: Fix unintentional sign extension issues")
Signed-off-by: David S. Miller <davem@davemloft.net>