linux.git/drivers/net, branch v4.18-rc7

net: axienet: Fix double deregister of mdio

2018-07-24T23:38:01+00:00

If the registration fails then mdio_unregister is called.
However at unbind the unregister ia attempted again resulting
in the below crash

[   73.544038] kernel BUG at drivers/net/phy/mdio_bus.c:415!
[   73.549362] Internal error: Oops - BUG: 0 [#1] SMP
[   73.554127] Modules linked in:
[   73.557168] CPU: 0 PID: 2249 Comm: sh Not tainted 4.14.0 #183
[   73.562895] Hardware name: xlnx,zynqmp (DT)
[   73.567062] task: ffffffc879e41180 task.stack: ffffff800cbe0000
[   73.572973] PC is at mdiobus_unregister+0x84/0x88
[   73.577656] LR is at axienet_mdio_teardown+0x18/0x30
[   73.582601] pc : [] lr : []
pstate: 20000145
[   73.589981] sp : ffffff800cbe3c30
[   73.593277] x29: ffffff800cbe3c30 x28: ffffffc879e41180
[   73.598573] x27: ffffff8008a21000 x26: 0000000000000040
[   73.603868] x25: 0000000000000124 x24: ffffffc879efe920
[   73.609164] x23: 0000000000000060 x22: ffffffc879e02000
[   73.614459] x21: ffffffc879e02800 x20: ffffffc87b0b8870
[   73.619754] x19: ffffffc879e02800 x18: 000000000000025d
[   73.625050] x17: 0000007f9a719ad0 x16: ffffff8008195bd8
[   73.630345] x15: 0000007f9a6b3d00 x14: 0000000000000010
[   73.635640] x13: 74656e7265687465 x12: 0000000000000030
[   73.640935] x11: 0000000000000030 x10: 0101010101010101
[   73.646231] x9 : 241f394f42533300 x8 : ffffffc8799f6e98
[   73.651526] x7 : ffffffc8799f6f18 x6 : ffffffc87b0ba318
[   73.656822] x5 : ffffffc87b0ba498 x4 : 0000000000000000
[   73.662117] x3 : 0000000000000000 x2 : 0000000000000008
[   73.667412] x1 : 0000000000000004 x0 : ffffffc8799f4000
[   73.672708] Process sh (pid: 2249, stack limit = 0xffffff800cbe0000)

Fix the same by making the bus NULL on unregister.

Signed-off-by: Shubhrajyoti Datta 
Signed-off-by: David S. Miller

qmi_wwan: fix interface number for DW5821e production firmware

2018-07-24T23:37:13+00:00

The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Fixes: e7e197edd09c25 ("qmi_wwan: add support for the Dell Wireless 5821e module")
Signed-off-by: Aleksander Morgado 
Acked-by: Bjørn Mork 
Signed-off-by: David S. Miller

bnx2x: Fix invalid memory access in rss hash config path.

2018-07-24T23:33:02+00:00

Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.

Please consider applying it to 'net' branch.

Signed-off-by: Sudarsana Reddy Kalluru 
Signed-off-by: David S. Miller

net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper

2018-07-24T23:30:48+00:00

Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.

However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.

Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).

Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein 
Signed-off-by: Tariq Toukan 
Signed-off-by: David S. Miller

r8169: restore previous behavior to accept BIOS WoL settings

2018-07-24T21:06:39+00:00

Commit 7edf6d314cd0 tried to resolve an inconsistency (BIOS WoL
settings are accepted, but device isn't wakeup-enabled) resulting
from a previous broken-BIOS workaround by making disabled WoL the
default.
This however had some side effects, most likely due to a broken BIOS
some systems don't properly resume from suspend when the MagicPacket
WoL bit isn't set in the chip, see
https://bugzilla.kernel.org/show_bug.cgi?id=200195
Therefore restore the WoL behavior from 4.16.

Reported-by: Albert Astals Cid 
Fixes: 7edf6d314cd0 ("r8169: disable WOL per default")
Signed-off-by: Heiner Kallweit 
Signed-off-by: David S. Miller

can: xilinx_can: fix power management handling

2018-07-23T12:34:46+00:00

There are several issues with the suspend/resume handling code of the
driver:

- The device is attached and detached in the runtime_suspend() and
  runtime_resume() callbacks if the interface is running. However,
  during xcan_chip_start() the interface is considered running,
  causing the resume handler to incorrectly call netif_start_queue()
  at the beginning of xcan_chip_start(), and on xcan_chip_start() error
  return the suspend handler detaches the device leaving the user
  unable to bring-up the device anymore.

- The device is not brought properly up on system resume. A reset is
  done and the code tries to determine the bus state after that.
  However, after reset the device is always in Configuration mode
  (down), so the state checking code does not make sense and
  communication will also not work.

- The suspend callback tries to set the device to sleep mode (low-power
  mode which monitors the bus and brings the device back to normal mode
  on activity), but then immediately disables the clocks (possibly
  before the device reaches the sleep mode), which does not make sense
  to me. If a clean shutdown is wanted before disabling clocks, we can
  just bring it down completely instead of only sleep mode.

Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.

The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.

xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.

Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.

Tested on Zynq-7000 integrated CAN.

Signed-off-by: Anssi Hannula 
Cc: Michal Simek 
Cc: 
Signed-off-by: Marc Kleine-Budde

can: xilinx_can: fix incorrect clear of non-processed interrupts

2018-07-23T12:34:46+00:00

xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.

Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula 
Cc: Michal Simek 
Cc: 
Signed-off-by: Marc Kleine-Budde

can: xilinx_can: fix RX overflow interrupt not being enabled

2018-07-23T12:34:46+00:00

RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).

Fix that by enabling the RXOFLW interrupt.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula 
Cc: Michal Simek 
Cc: 
Signed-off-by: Marc Kleine-Budde

can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting

2018-07-23T12:34:46+00:00

The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.

However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.

Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.

The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
  BUG!, TX FIFO full when queue awake!
messages to be output.

There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.

The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.

Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.

Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.

An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.

v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.

v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula 
Cc: 
Signed-off-by: Marc Kleine-Budde

can: xilinx_can: fix recovery from error states not being propagated

2018-07-23T12:34:45+00:00

The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.

Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44f50b ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula 
Cc: 
Signed-off-by: Marc Kleine-Budde