linux.git/drivers/net, branch v4.13-rc5

geneve: maximum value of VNI cannot be used

2017-08-10T05:41:04+00:00

Geneve's Virtual Network Identifier (VNI) is 24 bit long, so the range
of values for it would be from 0 to 16777215 (2^24 -1).  However, one
cannot create a geneve device with VNI set to 16777215. This patch fixes
this issue.

Signed-off-by: Girish Moodalbail 
Signed-off-by: David S. Miller

net: systemport: Fix software statistics for SYSTEMPORT Lite

2017-08-10T05:39:17+00:00

With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.

Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

qmi_wwan: fix NULL deref on disconnect

2017-08-09T04:14:16+00:00

qmi_wwan_disconnect is called twice when disconnecting devices with
separate control and data interfaces.  The first invocation will set
the interface data to NULL for both interfaces to flag that the
disconnect has been handled.  But the matching NULL check was left
out when qmi_wwan_disconnect was added, resulting in this oops:

  usb 2-1.4: USB disconnect, device number 4
  qmi_wwan 2-1.4:1.6 wwp0s29u1u4i6: unregister 'qmi_wwan' usb-0000:00:1d.0-1.4, WWAN/QMI device
  BUG: unable to handle kernel NULL pointer dereference at 00000000000000e0
  IP: qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  PGD 0
  P4D 0
  Oops: 0000 [#1] SMP
  Modules linked in: 
  CPU: 2 PID: 33 Comm: kworker/2:1 Tainted: G            E   4.12.3-nr44-normandy-r1500619820+ #1
  Hardware name: LENOVO 4291LR7/4291LR7, BIOS CBET4000 4.6-810-g50522254fb 07/21/2017
  Workqueue: usb_hub_wq hub_event [usbcore]
  task: ffff8c882b716040 task.stack: ffffb8e800d84000
  RIP: 0010:qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  RSP: 0018:ffffb8e800d87b38 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000001 RSI: ffff8c8824f3f1d0 RDI: ffff8c8824ef6400
  RBP: ffff8c8824ef6400 R08: 0000000000000000 R09: 0000000000000000
  R10: ffffb8e800d87780 R11: 0000000000000011 R12: ffffffffc07ea0e8
  R13: ffff8c8824e2e000 R14: ffff8c8824e2e098 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8c8835300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000000000e0 CR3: 0000000229ca5000 CR4: 00000000000406e0
  Call Trace:
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210
   ? qmi_wwan_unbind+0x6d/0xc0 [qmi_wwan]
   ? usbnet_disconnect+0x6c/0xf0 [usbnet]
   ? qmi_wwan_disconnect+0x87/0xc0 [qmi_wwan]
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210

Reported-and-tested-by: Nathaniel Roach 
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas 
Signed-off-by: Bjørn Mork 
Signed-off-by: David S. Miller

ppp: fix xmit recursion detection on ppp channels

2017-08-09T04:06:11+00:00

Commit e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.

This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.

Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.

Fixes: e5dadc65f9e0 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: Guillaume Nault 
Signed-off-by: David S. Miller

net: dsa: mediatek: add adjust link support for user ports

2017-08-09T01:01:25+00:00

Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.

Signed-off-by: Shashidhar Lakkavalli 
Signed-off-by: Muciri Gatimu 
Signed-off-by: John Crispin 
Signed-off-by: David S. Miller

net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets

2017-08-09T00:59:57+00:00

if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.

V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set

Reported-by: Shuang Li 
Fixes: f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti 
Acked-by: Saeed Mahameed 
Signed-off-by: David S. Miller

qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'

2017-08-07T21:56:15+00:00

We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.

'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.

Update the test and check the result of the 2 'kzalloc()' instead.

Signed-off-by: Christophe JAILLET 
Acked-by: Tomer Tayar 
Signed-off-by: David S. Miller

asix: Fix small memory leak in ax88772_unbind()

2017-08-07T17:10:19+00:00

When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().

This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.

Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().

Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.

Signed-off-by: Dean Jenkins 
Signed-off-by: David S. Miller

asix: Ensure asix_rx_fixup_info members are all reset

2017-08-07T17:10:19+00:00

There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.

For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.

Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.

Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.

In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.

Signed-off-by: Dean Jenkins 
Signed-off-by: David S. Miller

asix: Add rx->ax_skb = NULL after usbnet_skb_return()

2017-08-07T17:10:19+00:00

In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().

The risks include:

a) asynchronously freeing rx->ax_skb after passing the netdev buffer
   to the NAPI layer which might corrupt the backlog queue.

b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
   times which causes writing off the end of the netdev buffer.

Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.

Signed-off-by: Dean Jenkins 
Signed-off-by: David S. Miller